• 대한의용생체공학회:의공학회지
• /
• 제24권2호
• /
• pp.127-132
• /
• 2003

본 논문에서는 관절 경직 환자의 재활 치료를 위한 공압 실린더를 이용한 하이브리드형 로봇을 연구 개발하였다. 공압 실린더는 우수한 컴플라이언스를 가지고 있고 부피나 중량에 비해 높은 구동력을 가지고 있다 낮은 강성을 지닌 공압 구동기는 안정이 보장되어야 하는 물리 치료용 로봇의 구현에 적용하기 적당하다. 본 연구에서 제안한 로봇 시스템은 직렬형과 병렬형을 결합한 하이브리드 형으로 위치 결정부와 자세 결정부로 구분되며 하이브리드 구조를 통해 넓은 작업영역과 구동력을 얻을 수 있었다. 슬라이딩 모드 제어기를 이용하여 로봇 시스템의 공압 서보시스템의 추종성과 안정성을 얻을 수 있었으며 실험을 통하여서 개발된 시스템에 대한 검증을 하였다.

• 한국고분자학회:학술대회논문집
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.339-339
• /
• 2006

In this study, the microvoids in glassy polymers were investigated by Xe sorption and $^{129}Xe$ NMR measurements. Xe sorption isotherms of glassy polymers have been successfully interpreted by the dual-mode sorption model. $^{129}Xe$ NMR chemical shift of the $^{129}Xe$ in the samples show nonlinear low-field shift with increasing sorption amount of Xe because of a fast exchange of Xe atoms between Henry and Langmuir sites, whereas it has showed linear shift against sorption amount of Xe into the Langmuir site. From this Xe-density dependence of the $^{129}Xe$ NMR chemical shift, it has been able to estimate mean size of the microvoids in glassy polymer. It is confirmed that there is correlation between ${C_H}'$ and volume or number of microvoids. From these findings, it is demonstrated that $^{129}Xe$ NMR spectroscopy is a powerful technique to determine the mean size and number of microvoids in glassy polymers.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.149-152
• /
• 2009

직접분사방식 추력기 노즐오리피스로부터 분사되는 분무입자의 발달특성을 연구하기 위해 분무의 다양한 위치에서 평균속도, 직경, 그리고 부피유속과 같은 분무특성인자들을 측정한다. 실험 결과로부터, 고속의 큰 직경을 갖는 분무 입자들이 주변 공기로의 운동량 손실로 인해 하류로 이동함에 따라 저속의 작은 입자로 분열한다. 또, 분무 확산 및 분산에 의해 높은 부피유속의 영역이 반경방향으로 넓게 확장된다.

• E2M - 전기 전자와 첨단 소재
• /
• 제7권1호
• /
• pp.32-41
• /
• 1994

In this study, the TSC spectroscopy has been applied to investigate the influence of structural change due to a process of curing reaction on the electrical properties of epoxy composites cured with acid-anhydride. Five TSC peaks appeared in -160-250[.deg.C]: in the low temperature region below glass transition temperature(T$\_$g/), three relaxation mode peaks due to action of side chains, substitution group or terminal groups have been observed, a peak associated with T$\_$g/, appeared in 110[.deg. C] and p peak due to ionic space charges located in 150[.deg.C]. Each peak was separated into elementary peaks by the partial polarization procedure, and the distribution of activation energy and relaxation time were analized to clearify the origin of each peak. Also, overaboundantly added hardener separated a .betha. peak near 10[.deg. C] into two peaks of .betha.$\_$1/(10.deg. C) and .betha.$\_$2/(20.deg. C) according to increasement of forming field, and the separated hardener was oxidated thermally with increasing surrounding temperatures. The expansion of the free volume need in molecular motion and the reduction of the structural packing density through thermal oxidation process increased TSC between .alpha. peak and .betha. peak and decreased T$\_$g/.

• 한국소음진동공학회논문집
• /
• 제14권10호
• /
• pp.1007-1014
• /
• 2004

This paper presents a study of low frequencies volume velocity vibration control of a smart panel in order to reduce sound transmission. A distributed piezoelectric quadratically shaped polyvinylidene fluoride (PVDF) polymer film is used as a uniform force actuator and an array of $4\;{\times}\;4$ accelerometer is used as a volume velocity sensor for the implementation of a single-input single-output control system. The theoretical and experimental study of sensor-.actuator frequency response function shows that this sensor-actuator arrangement provides a required strictly positive real frequency response function below about 900 Hz. Direct velocity feedback could therefore be implemented with a limited gain which gives reductions of about 15 dB in vibration level and about 8 dB in acoustic power level at the (1,1) mode of the smart panel. It has been also shown that the shaping error of PVDF actuator could limit the stability and performance of the control system.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2003년도 춘계학술대회논문집
• /
• pp.368-373
• /
• 2003

This paper presents a study of low frequencies volume velocity vibration control of a smart panel in order to reduce sound transmission. A distributed piezoelectric quadratically shaped polyvinylidene fluoride (PVDF) polymer film is used as a uniform force actuator and an array of 4$\times$4 accelerometer is used as a volume velocity sensor for the implementation of a single-input single-output con rot system. The theoretical and experimental study of sensor-actuator frequency response function sho vs that this sensor-actuator arrangement provides a required strictly positive real frequency response function below about 900Hz. Direct velocity feedback could therefore be implemented with a limited gain which gives reductions of about 15㏈ in vibration level and about 8 ㏈ in acoustic power level at the (1, 1) mode of the smart Panel. It has been also shown that the shaping error of PVDF actuator could limit he stability and performance of the control system.

• 한국연소학회지
• /
• 제22권2호
• /
• pp.42-49
• /
• 2017

A premixed combustion has many advantages including low NOx and CO emission, high thermal efficiency and a small volume of combustor. This study focused on combustion characteristics in a premixed combustion burner using the nickel based metal foam. The results show that the blue flame is found to be very stable at heating load 6,300-25,200 kcal/h by implementing the proper nickel based metal foam and baffle plate. The premixed flame mode is changed into green flame, red flame, blue flame and lift off flame with decreasing equivalence ratio. NOx emission was measured 80 ppm(0% oxygen base) from 0.710 to 0.810 of equivalence ratio and CO emission is 90 ppm(0% oxygen base) under the same equivalence ratio. It is also found that the stable blue flame region in flame stability curve becomes wider with increasing the heat load.

• Tribology and Lubricants
• /
• 제26권5호
• /
• pp.291-296
• /
• 2010

The purpose of this paper is to study the fuel economy improvement experimentally when the viscosity of engine oil is lowered. The emissions are measured for CVS-75 mode with SAE viscosity grades. The test results indicate that a close correlation has been found between the engine oil viscosity and the fuel economy. The lowering of engine oil viscosity causes the reduction of friction loss which has a very close relation with the fuel economy. These results as the lowering of engine oil viscosity will be a important factor for improvement of the fuel economy and reduction of the $CO_2$ emission.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1835-1841
• /
• 2017

An improved single-phase full-bridge zero-voltage-switching inverter using a subtractive coupled magnetics is proposed in this paper. The proposed topology overcomes several drawbacks of the conventional ARCPI zero-voltage-switching inverter including two bulky capacitors which can cause problems such as the need for a protection circuit and voltage fluctuation of split capacitors. Also the proposed topology can reduce the number of devices required for ZVS through a simplified auxiliary circuit, thus achieving low cost and small volume and is applicable a modified unipolar PWM scheme. Detail mode analysis and design considerations are provided for optimal efficiency. In the end, the effectiveness and feasibility of the proposed topology are verified experimentally under various conditions.

• Structural Engineering and Mechanics
• /
• 제51권6호
• /
• pp.1017-1036
• /
• 2014

Steel tubes have an efficient shape with large second moment of inertia relative to their light weight. One of the main problems of these members is their low buckling resistance caused from having thin walls. In this study, steel foams with high strength over weight ratio is used to fill the steel tube to beneficially modify the response of steel tubes. The linear eigenvalue and plastic collapse FE analysis is done on steel foam filled tube under pure compression and three point bending simulation. It is shown that steel foam improves the maximum strength and the ability of energy absorption of the steel tubes significantly. Different configurations with different volume of steel foam and composite behavior is investigated. It is demonstrated that there are some optimum configurations with more efficient behavior. If composite action between steel foam and steel increases, the strength of the element will improve, in a way that, the failure mode change from local buckling to yielding.