• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1885-1890
• /
• 2004

In this paper the numerical method with a zonal embedded grid system was applied to the spin-up flow within a semi-circular container. Flow visualization was also performed on a rotating table. The results show that at a low level of damping (i.e. low viscosity and high liquid depth) a cyclonic cell produced initially near the left-hand-side corner of the container moves along a wall and merged with the cell on the right-hand-side.

• 한국초전도ㆍ저온공학회논문지
• /
• 제15권2호
• /
• pp.20-23
• /
• 2013

For sensitive measurements of micro-Tesla nuclear magnetic resonance (${\mu}T$-NMR) signal, a low-noise superconducting quantum interference device (SQUID) system is needed. We have fabricated a liquid He dewar for an SQUID having a large diameter for the pickup coil. The initial test of the SQUID system showed much higher low-frequency magnetic noise caused by the thermal magnetic noise of the aluminum plates used for the vapor-cooled thermal shield material. The frequency dependence of the noise spectrum showed that the noise increases with the decrease of frequency. This behavior could be explained from a two-layer model; one generating the thermal noise and the other one shielding the thermal noise by eddy-current shielding. And the eddy-current shielding effect is strongly dependent on the frequency through the skin-depth. To minimize the loop size for the fluctuating thermal noise current, we changed the thermal shield material into insulated thin Cu mesh. The magnetic noise of the SQUID system became flat down to 0.1 Hz with a white noise of 0.3 $fT/{\surd}Hz$, including the other noise contributions such as SQUID electronics and magnetically shielded room, etc, which is acceptable for low-noise ${\mu}T$-NMR experiments.

• ETRI Journal
• /
• 제24권5호
• /
• pp.349-359
• /
• 2002

With Ni/Au and Pd/Au metal schemes and low temperature processing, we formed low resistance stable Ohmic contacts to p-type GaN. Our investigation was preceded by conventional cleaning, followed by treatment in boiling $HNO_3$:HCl (1:3). Metallization was by thermally evaporating 30 nm Ni/15 nm Au or 25 nm Pd/15 nm Au. After heat treatment in $O_2$ + $N_2$ at various temperatures, the contacts were subsequently cooled in liquid nitrogen. Cryogenic cooling following heat treatment at $600^{\circ}C$ decreased the specific contact resistance from $9.84{\times}10^{-4}$ ${\Omega}cm^2$ to $2.65{\times}10^{-4}$ ${\Omega}cm^2$ for the Ni/Au contacts, while this increased it from $1.80{\times}10^{-4}$ ${\Omega}cm^2$ to $3.34{\times}10^{-4}$ ${\Omega}cm^2$ for the Pd/Au contacts. The Ni/Au contacts showed slightly higher specific contact resistance than the Pd/Au contacts, although they were more stable than the Pd contacts. X-ray photoelectron spectroscopy depth profiling showed the Ni contacts to be NiO followed by Au at the interface for the Ni/Au contacts, whereas the Pd/Au contacts exhibited a Pd:Au solid solution. The contacts quenched in liquid nitrogen following sintering were much more uniform under atomic force microscopy examination and gave a 3 times lower contact resistance with the Ni/Au design. Current-voltage-temperature analysis revealed that conduction was predominantly by thermionic field emission.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.190.1-190.1
• /
• 2015

Graphite has excellent mechanical and physical properties. It is known to advanced materials and is used to materials for molds, thermal treatment of furnace, sinter of diamond and cemented carbide tool etc. SiC materials are coated on the surface and holes of graphite to protect particles emitted from porous graphite with 5%~20% porosity and make graphite hard surface. SiC materials have high durability and thermal stability. Thermal CVD method is widely used to manufacture SiC thin films but high cost of machine investment and production are required. SiC thin films manufactured by Si reaction liquid and vapore with carbon are effective because of low cost of machine and production. SiC thin films made by vapor silicon infiltration into porous graphite can be obtained for shorter time than liquid silicon. Si materials are evaporated to the graphite surface in about $10^{-2}$ torr and high temperature. Si materials are melted in $1410^{\circ}C$. Si vapor is infiltrated into the surface hole of porous graphite and $Si_xC_y$ compound is made. $Si_x$ component is proportional to the Si vapor concentration. Si diffusion coefficient is estimated from quadratic equation obtained by Fick's second law. The steady stae is assumed. Si concentration variation for the depth from graphite surface is fitted to quadratic equation. Diffusion coefficient of Si vapor is estimated at about $10^{-8}cm^2s^{-1}$.

• Smart Structures and Systems
• /
• 제21권1호
• /
• pp.37-51
• /
• 2018

Tuned Liquid Dampers (TLDs) have gained wide acceptance as a system for structural control and energy dissipation. However, they face limitation caused by low damping in deep water, which affects their efficiency. Another problem with deep water TLDs is that not all water depth participates in energy dissipation. This paper investigated the effect of upper mounted baffles on the effectiveness of TLDs. The Vertical Blockage Ratio (VBR) of baffles ranged from 10% - 90%. The TLD (with and without baffle), structure, and combined structure with TLD (with and without baffles) were subjected to free and harmonic forced vibrations. Results indicated that baffles could significantly enhance the energy dissipation of TLDs, thus reducing structural responses more than structures equipped with ordinary TLDs. It was found that, there was an optimum value of VBR in which the TLD's efficiency was maximized. When TLD had an appropriate VBR, the structural acceleration and displacement responses were suppressed significantly up to 51% and 56%, respectively.

• Structural Engineering and Mechanics
• /
• 제60권1호
• /
• pp.131-148
• /
• 2016

Tuned Liquid Dampers (TLDs) provide low damping when it comes to deep water condition, and that not all water depth is mobilized in energy dissipation. This research focussed on a method to improve the efficiency of TLDs with deep water condition. Several bottom-mounted baffles were installed inside a TLD and the dynamic characteristics of modified TLDs together with their effect on the vibration control of a SDOF structure were studied experimentally. A series of free vibration and harmonic forced vibration tests were carried out. The controlling parameter in the conducted tests was the Vertical Blocking Ratio (VBR) of baffles. Results indicated that increase in VBR decreases the natural frequency of TLD and increases its damping ratio. It was found that the VBR range of 10% to 30% reduced response of the structure significantly. The modified TLD with the VBR of 30% showed the best performance when reduction in structural responses under harmonic excitations were compared.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.39-44
• /
• 2008

In this paper, heat transfer coefficients were measured in a channel with one side dimpled surface. The sphere type dimples were fabricated and the diameter and depth of dimple was 16mm and 4mm, respectively. Two channel heights of about 0.6 and 1.2 time of the dimple diameter, two dimple configuration were tested. The Reynolds numbers based on the channel hydraulic diameter was varied from 30000 to 50000. The improved hue detection based transient liquid crystal technique was used in the heat transfer measurement. Heat transfer measurement results showed that high heat transfer was induced downstream of dimples due to flow reattachment. Due to the flow recirculation on the upstream side in the dimple, the heat transfer coefficient was very low. As the Reynolds increased, the overall heat transfer coefficients also increased. With same dimple arrangement, the heat transfer coefficients and the thermal performance factor were higher for the lower channel height. As the distance between dimples became smaller, the overall heat transfer coefficient and the thermal performance factor were increased.

• 대한기계학회논문집B
• /
• 제26권7호
• /
• pp.1005-1013
• /
• 2002

Spin-up is a transient flow phenomenon occurring in a container when it starts to rotate from rest or its rotational speed increases from a low to high value. However, most studies on this subject have been for two-dimensional approximation. In this study, spin-up flows in a shallow rectangular container are analysed by using three-dimensional computation. We compared our results with those obtained by others using basically two-dimensional computation. Effect of two parameters, Reynolds number and liquid depth on the flow evolution is studied. We found that 2-D result is not accurate enough, and the vertical velocity distribution should be assumed of a fourth-order polynomial function for a better comparison.

• 한국지반환경공학회 논문집
• /
• 제16권11호
• /
• pp.39-43
• /
• 2015

본 연구에서는 압밀 배수를 촉진하기 위한 공법에서 사용되는 조립토나 골재로의 세립토 관입 정도를 다양한 조건에서 실험을 통해 확인하여 세립토의 조립토나 골재로의 관입특성을 규명하였다. 지중응력에 대응하는 압력의 크기나 세립토 함수비의 변화에 상관없이 해성점토가 해사나 표준사로는 관입되지 않아 모래 배수/말뚝 체에서의 배수저항 현상은 전혀 발생하지 않은 것으로 확인되었고, 오히려 물다짐에 의한 모래 배수/말뚝 체의 전단강도가 크게 증대한 것으로 보인다. 골재의 경우에는 골재의 입경이 클수록 해성점토의 관입깊이는 증대하고, 같은 골재라도 압력이나 함수비가 클수록 해성점토의 관입깊이는 증대함을 알 수 있었으며, 액성한계보다 작은 함수비를 갖는 해성점토는 입자가 작은 편인 13mm 골재로의 관입깊이가 현저하게 줄어들어 그 관입깊이가 상당히 적다 하더라도 일단 관입된 세립토에 의해 배수/말뚝 체에서의 배수저항 현상이 발생할 것으로 사료된다. 따라서 자연함수비가 액성한계보다 큰 매우 연약한 세립토층에서는 모래보다 큰 입경을 갖는 쇄석이나 자갈 등 골재를 사용하는 gravel drain 공법 및 gravel compaction pile 공법 등의 적용을 지양해야 하고, 자연함수비가 액성한계보다 작은 연약한 세립토 지반에서도 gravel drain 공법 및 gravel compaction pile 공법 등과 같은 연직배수공법을 적용할 경우 그 효용성은 크게 저하할 것으로 사료된다.

• 한국방사선학회논문지
• /
• 제17권6호
• /
• pp.957-964
• /
• 2023

본 연구는 시중에 판매되고 있는 다양한 성분과 제형의 손 소독제들을 전파 매질로 활용하여 초음파 검사를 진행한 후 획득한 영상을 평가·비교하여 기존의 초음파 젤의 대체 가능성을 확인하고자 하였다. 연구 방법으로는 점도가 낮은 liquid type을 제외한 gel type, cream type, foam type의 제형의 제품들을 선정해 에탄올 62% gel type 1개와 cream type 1개, 벤잘코늄 염화물 0.066% cream type 1개와 foam type 1개를 각각 초음파 매질로 사용하여, 축방향 & 측방향 분해능, 투과심도, probe와 phantom 사이의 공기층 형성유무에 관한 영상 평가를 진행하였다. 그 결과, 축방향 & 측방향 분해능 평가와 투과심도 평가에서 4개 실험군 모두 평가 기준에 적합한 결과가 나왔다. 그러나 foam type의 경우 분해능과 투과심도의 평가 기준에는 적합하지만 영상 평가 시 관찰 중심부를 제외한 양 측면부에서 어두운 음영으로 나타났다. 해당 실험을 통해 foam type을 제외한 나머지 3종의 손 소독제는 초음파 젤을 대체할 수 있을 것으로 사료된다.