• Textile Coloration and Finishing
• /
• v.8 no.2
• /
• pp.56-63
• /
• 1996

Low-temperature plasma treatment or sputter etching is of interest as one of the techniques to modify polymer surface. In this study, poly(ethylene terephthalate)(PET), nylon 6 and cotton fabrics dyed three black dyes were subjected to low-temperature argon plasma and also sputter etching. In relation to bathochromic effect, the surface characteristics of the treated fabrics and films were investigated by means of critical surface tension, SEM and ESCA measurement. The depth of shade of fabrics more increased by the sputter etching technique than argon plasma treatment. Many microcraters on the fiber surface formed by the sputter etching resulted in increase of surface area of the fiber and wettability, but the hydrophobic group was increased by the results of ESCA analysis. In particular the change in reflective index of the fibers was much more effective than the chemical composition of the fiber surface on increasing of the depth of shade.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.2
• /
• pp.133-139
• /
• 2017

The timing chain system, which is a typical power transmission technology applied to a vehicle, has been widely used by the automotive industry because it is normally designed to last a car's lifetime. However, the timing chain system may cause some problems due to the shape of the chains and the polygonal behavior on contact between the chain and the sprocket. In addition, noise and vibration caused by transmission error are the most typical problems encountered by major automotive manufacturers and they are considered as the main source of customer complaint. The initial tension of the chain-sprocket system is thought to be the main cause of transmission error, and it is regarded as the source of engine vibration and noise. The initial tension of the chain system should be controlled carefully since a low initial tension can cause twisting, which may lead to a system malfunction, while a high initial tension can reduce the service life due to a worn down contact surface. In this paper, the kinematic analysis model is generated with various initial tensions, which are controlled by changing the shape of the fixed guide with the largest contact surface with chain. The results showed that the transmission error was minimized on a particular range of initial tension, and the tendency showed that the error changed with a higher sensitivity at a lower initial tension.

• Journal of the Korean Ceramic Society
• /
• v.18 no.3
• /
• pp.192-200
• /
• 1981

This study deals with the low temperature ($25^{\circ}C$-$600^{\circ}C$) properties of Kaolin-Phosphate-water systems. Phosphoric acid, mono aluminum phosphate, mono ammonium phosphate, the mixture of phosphoric acid and mono aluminum phosphate, and the mixture of phosphoric acid and mono ammonium phosphate were used to characterize the M.O.R. of the systems with to quantity of phosphates, curing time, and firing temperature. Firing shrinkage, viscosity, surface tension, DTA, TGA, and X-ray diffraction patterns were also measured in order to investigated the factors of strengthening. The results of this study were summarized as follows: 1. The M.O.R. of kaolin-phosphate systems were stronger than that of Kaolin-water system at room temperature or low temperature($25^{\circ}C$-$600^{\circ}C$). Though it was increased according to the longer curing time, the higher temperature, and the more addition of phosphate, the M.O.R. were decreased in the case of 10 wt% phosphate addition in the system of phosphoric acid, mono aluminum phosphate and phosphoric acid-mono aluminum phosphate. 2. When the concentration of Phosphate was at 4 wt%, the M.O.R. of specimen cured at $25^{\circ}C$ and added to the phosphoric acid was strongest among the specimens in added to the others phosphates. Whereas, when the concentration of phosphate was above 6wt%, the M.O.R. of specimen cured at $25^{\circ}C$ and added to the phosphoric acid mono ammonium phosphate system cured at $25^{\circ}C$ was the strongest. 3. The M.O.R. of the specimen heated, in the temperature range of 15$0^{\circ}C$-1$600^{\circ}C$, and added to the mixture of phosphoric acid-mono aluminum phosphate system or phosphoric acid-mono ammonium phosphate system was stronger than that of specimen added to Phosphoric acid, mono-aluminum Phosphate or mono-ammonium phosphate alone. 4. The bonding force of phosphate binders was more closely related to surface tension than viscosity and it tended to be inversely proportional to surface tension. The bonding force after heating treatment seemed to be caused by the change of structure of phosphate according to heating.

• Fashion & Textile Research Journal
• /
• v.9 no.1
• /
• pp.113-118
• /
• 2007

It is well recognized that the wicking of liquids in a textile fabric takes place mainly through a capillary system composed of the individual fibers. Considering typical dyeing stages, it is thought that a high dye uptake on the fabric probably depends on the wickability. Three kinds of barely water soluble ketones, acetophenone(A), 2-pentanone(2P) and 3-pentanone(3P) were separately dissolved in methanol(M) and then each was mixed with aqueous solution of C. I. Red Acid 114. Wicking heights of dyeing solutions were measured under such conditions that the effect of gravity was negligible. The result could be graphed as a series of straight lines having the form s = $kt^{1/2}$, where s was distance traveled by the solutions, t was time, and k was slope of the line. The surface tension(${\gamma}$) of the ketones had more signifcant effect on the wickability compared to the viscosity(${\eta}$) of them. The greater wickability resulted in the higher dye uptake on the fabric and the order of wickabilty was equal to that of the surface tension(${\gamma}$) and dye uptake on the fabric, A>3P>2P>M.

• Journal of the Korean Applied Science and Technology
• /
• v.9 no.2
• /
• pp.107-117
• /
• 1992

The synthesis and solution properties of polyglycerol alkyl ether($R_{12}Gn$) are described. The phase behavior, surface tension, cloud point and HLB value of polyglycerol dodecyl ether in aqueous solution and in mixed solution of surfactant /water /oil have been investigated and compared with values of polyoxyethylene dodecyl ether. The surface tension showed that $R_{12}Gn$ have sufficiently low values of surface tension and cmc to serve as useful polyoxyethylene alkyl ether. The mesophases appearing in the $R_{12}Gn$ systems were more stable in a high temperature range than the mesophases of polyoxyethylene alkyl ether systems. The cloud point and HLB data indicated that addition of one glycerol group was equivalent to the addition of three oxyethylene group units, as far as the hydrophilic property was concerned. The phase diagrams of the polyglycerol alkyl ether /dodecane /water systems showed that the solubilizing and emulsifying powers of $R_{12}Gn$ were greater than those of polyoxyethylene alkyl ether. It is concluded that the polyglycerol chain can be even more useful as hydrophilic group of nonionic surfactants than the polyoxyethylene chain.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.6
• /
• pp.701-706
• /
• 2005

Pipes, tubes. and tubular sections with external transverse high fins have been used extensively for heating cooling, and degumidifying air and other gases. This work was performed to investigate an air side heat transfer charactieristics of minichannel with tension wound transverse fin. This estimate was confirmed conversion heat capacity the air side surface area enlargement and heat transfer charactieristics performed available inlet tube side hot water mass flux or outlet tube side air frontal air velocity. The most suitable tension wound transverse finned minichannel was measured extremely low in air side pressure drop and fin effectiveness $3.3\~4.4$. The pressure drop $0.9\~2.8Pa$ was ranged frontal air velocity $0.5\~1.2m/s$. It is also appeared that heat transfer in air side could be better conversion heat area which has been increased $330\%$ of heat capacity compared with the bare tube.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.10 s.241
• /
• pp.1111-1118
• /
• 2005

In this study, a unified numerical investigation has been performed on the evolution of weld pool and key-hole geometry during low-power and high-power density laser welding. Unsteady phase-change heat transfer and fluid flow with the surface tension are examined. The one-dimensional vaporization model is introduced to model the overheated surface temperature and recoil pressure during high-power density laser welding. It is shown that Marangoni convection in the weld pool is dominant at low-power density laser welding, and the keyhole with thin liquid layer and the hump are visible at high-power density laser welding. It is also shown that the transition from conduction welding to penetration welding fur iron plate exists when the laser power density is about $10^6W/Cm^2$.

• Journal of Korean Ophthalmic Optics Society
• /
• v.19 no.1
• /
• pp.23-30
• /
• 2014

Purpose: The present study was aimed to figure out the correlation amongst the evaluation methods for critical micelle concentration, surface tension and protein cleaning efficacy to evaluate cleaning efficacy of contact lens care products. Methods: The critical micelle concentration of surfactants and the actual concentration of surfactants in contact lens care solutions were investigated by employing references published and related information. Surface tension of contact lens care solutions was measured by surface tension device at $25{\pm}1^{\circ}C$, and contact lenses made of lotrafilcon A, comfilcon A and balafilcon A were washed with contact lens care solutions after the incubation in artificial tears for 14 days and their cleaning efficacy was compared. Results: Among the 22 contact lens care products, 9 products provided the label of the concentration of surfactant, and 7 products showed higher concentration of surfactant than the critical micelle concentration reported in references. As a result of measuring surface tension, the surface tension of lens care products for soft contact lens was generally lower than other care products. When examined the removal effect of protein deposited on lens surface, it was known that the care products having lower surface tension showed higher protein removal efficiency. Conclusions: The surface tension is low when surfactant concentration in contact lens care solutions is high, and the removal effect of protein deposited is accordingly increased with the decrease of surface tension. Thus, these indicate the correlation amongst the evaluation methods for cleaning efficacy.

• Journal of the Korean Ceramic Society
• /
• v.33 no.12
• /
• pp.1325-1330
• /
• 1996

A new numerical method for determining the surface tension of a liquid drop by experimental measurement of the contour of the sessile drop is explained. in the present method a very simple and short computer program enables the calculation of surface tension in a few seconds even by a low speed personal computer. It need not the use of any other numerical tables or complex techniques. X and Z-corrdinates at one point on the contour of a sessile drop and the tangential angle at that point are all the data needed when the density of the drop is known. The results were compared with the values derived by a conventional method. This method can be used for the confirmation of measuring accuracy. Also the same concepts can be applied for the pendant drop method by changing only the sign of Z-coordinate from "+" to "-"ot; to "-"ot;-"quot.

• Journal of the Korea Institute of Building Construction
• /
• v.12 no.1
• /
• pp.64-72
• /
• 2012

Recently, prepackaged-type surface preparation materials using redispersible polymer powders are widely used for interior and exterior finishing in the construction work. The purpose of this study is to evaluate the performance and the quality of prepackaged-type surface preparation materials using a VA/E/MMA terpolymer powder. Surface preparation materials using a VA/E/MMA terpolymer powder were prepared with shrinkage reducing agent contents of 0, 4 % and cellulose fiber contents of 0, 0.5, 1.0 %, and tested for drying shrinkage, strengths, adhesion in tension, crack and impact resistance, water absorption, permeability. As a result, prepackaged-type surface preparation materials show outstanding performance depending on the shrinkage reducing agent and cellulose fiber contents.