• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2201-2203
• /
• 1999

In this study, we have designed and manufactured not a present elliptic cavity but a circular cavity and we have experimented the operational characteristics. As a result, we obtained the maximum efficiency of 2.1 %. It didn't have any difference compared with elliptic cavity. A circular cavity is much more compact, so far easier to be manufactured than a elliptic cavity. And it can be made at a low cost. At the input energy, parameter $\alpha$, input voltage, and pulse width were in the same condition, we have decided to the optimization of the mesh number of a parallel-mesh circuit which was connected with main power supply.

• Journal of Oral Medicine and Pain
• /
• v.12 no.1
• /
• pp.5-16
• /
• 1987

레이저의 의학적 이용은 고출력 레이저의 외과적 이용과 더불어 많은 진전을 하게 되었다. 근래에는 인체에 손상을 주는 고출력 레이저 외에도 조직의 파괴없이 인체조직에 유용한 효과를 줄 수 있는 저출력 레이저에 대한 연구가 적극적으로 시도되고 있다. 본 연구는 치은염을 가진 13명의 대상에 대해 Split-mouth design으로 대조군 및 실험군을 설정하여 실험군의 치은에 저출력 레이저(Biotherapy dental Laser 3DL)를 격일로 4회 조사한 후 plaque index, pocket depth, sulcus bleeding index, supragingival과 subgingival plaque의 bacterial morphotype의 비율 및 광학현미경을 통한 조직학적 염증 침윤상을 측정 평가하여 다음과 같은 결과를 얻었다. 1) 레이저 조사후 SBI(p<0.01)는 감소하였으나 PI는 별다른 변화가 없었다. 2) 레이저 조사에 따라 spirochetes(p<0.01)를 포함하여 motiles(p<0.05, p<0.01)은 감소된 반면 nommotiles(p<0.05, p<0.01) 증가하였다. 3) 레이저 조사 치은에서는 염증세포 침윤이 Dental(p<0.05) 및 oral(p<0.01) 양측 모두 감소되었다.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.5
• /
• pp.226-229
• /
• 2010

Many methods exist that promote wound healing, including light therapy, which consists of light beams that assist the human body in treating and sterilizing wounds, as well as regenerating cells. Irradiation with specific wavelengths of either laser or LED light has been shown to induce beneficial proliferation of fibroblasts that, depending on the size of the wound, can be effective in promoting wound healing. The experiments in this study utilized 8 week old 250~300 g Male Sprague Dawley Rats (ILAR Code: NTacSam:SD) and included a non-irradiation group and a 525 nm green LED irradiation group (n of each group = 7). In experiments animals were allowed to rest for 24 hours after wounds had been excised, which was followed by non- irradiation or 525 nm green LED irradiation therapy one hour per day for 9 days. Immunohistochemical staining was conducted for cytokeratin in order to precisely measure the defect size. In addition, Masson's trichrome staining was utilized in order to compare levels of collagen between the 525 nm green LED irradiation group and the non-irradiation group. Animals exposed to 525 nm green LED irradiation (p<0.05) healed at a faster rate and had increased collagenosis compared with the non-irradiated control group. Thus, treatment with 525 nm green LED irradiation had a beneficial effect on wound healing and should be considered as a possible alternative to low power laser treatment.

• Journal of the Optical Society of Korea
• /
• v.16 no.3
• /
• pp.313-317
• /
• 2012

We have evaluated a 1.3 ${\mu}m$ vertical-cavity surface-emitting laser (VCSEL), whose bottom mirror and central active layer were grown by metal organic chemical vapor deposition (MOCVD) and whose top mirror was covered with a dielectric coating, for 10 Gb/s data transmission over single-mode fibers (SMFs). Successful demonstration of error-free transmission of the directly modulated VCSEL signals at data rate of 10 Gb/s over a 10 km-long SMF was achieved for operating temperatures from $20^{\circ}C$ to $60^{\circ}C$ up to bit-error-rate (BER) of $10^{-12}$. The DC bias current and modulation currents are only 7 mA and 6 mA, respectively. The results indicate that the VCSEL is a good low-power consuming optical signal source for 10 GBASE Ethernet applications under controlled environments.

• Korean Journal of Optics and Photonics
• /
• v.11 no.3
• /
• pp.141-146
• /
• 2000

Mie particles such as polystylene latex spheres with $3~5{\mu}m$ diameters are easily trapped and freely moved toward an arbitrary position by using the low power He-Ne laser beam focussed by the objective lens with the magnification of 40 X or 100 X. By using this technology, we can successfully arrange Mie particles in the form of the capital letter A. As a result, we can confirm the possibility of the optical tweezer that can readily trap and freely move the Mie particles. icles.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.128-128
• /
• 2003

Electrochromism (EC) is defined as a phenomenon in which a change in color takes place in the presence of an applied voltage. Because of their low power consumption, high coloration efficiency, EC devices have a variety of potential applications in smart windows, mirror, and optical switching devices. An EC devices generally consist of a transparent conducting layer, electrochromic cathodic and anodic coloring materials and an ion conducting electrolyte. EC has been widely studied in transition metal oxides(e.g., WO$_3$, NiO, V$_2$O$\sub$5/) Among these materials, WO$_3$ is a most interesting material for cathodic coloration materials due to its lush coloration efficiency (CE), large dynamic range, cyclic reversibility, and low cost material. WO$_3$ films have been prepared by a variety of methods including vacuum evaporation, chemical vapor deposition, electrodeposition process, sol-gel synthesis, sputtering, and laser ablation. Sol-gel process is widely used for oxide film at low temperature in atmosphere and requires lower capital investment to deposit large area coating compared to vacuum deposition process.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.5
• /
• pp.94-100
• /
• 2002

This paper is concerned with the development, and performance test of LIPCA (Lightweight Piezo-composite Curved Actuator) that is lighter than other conventional piezo-composite type actuators. LIPCA is composed of top fiber composite layers with a high modulus and low CTE (Coefficient of Thermal Expansion), a middle PZT cermaic wafer, and base layers with a high modulus and high CTE. The performance of each actuator was evaluated using an actuator test system consisting of an actuator supporting jig, a high voltage actuating power supplier, and a non-contact laser measuring system. The simply supported condition actuator was excited by the power supplier with 1.0Hz cycle and up to $100\sim400V_{pp}$. The displacement at the center point of actuator was measured with non-contact laser displacement measuring system, It has been shown that the LIPCA-C2 can 34% decrease in mass and 13% increase in displacement compared to THUNDER.

• Nuclear Engineering and Technology
• /
• v.53 no.4
• /
• pp.1189-1198
• /
• 2021

When performing remote tasks using robots in nuclear power plants, a 3D shape measurement system is advantageous in improving the efficiency of remote operations by easily identifying the current state of the target object for example, size, shape, and distance information. Nuclear power plants have high-radiation and underwater environments therefore the electronic parts that comprise 3D shape measurement systems are prone to degradation and thus cannot be used for a long period of time. Also, given the refraction caused by a medium change in the underwater environment, optical design constraints and calibration methods for them are required. The present study proposed a method for developing an underwater 3D shape measurement system with improved radiation tolerance, which is composed of commercial electric parts and a stereo camera while being capable of easily and readily correcting underwater refraction. In an effort to improve its radiation tolerance, the number of parts that are exposed to a radiation environment was minimized to include only necessary components, such as a line beam laser, a motor to rotate the line beam laser, and a stereo camera. Given that a signal processing circuit and control circuit of the camera is susceptible to radiation, an image sensor and lens of the camera were separated from its main body to improve radiation tolerance. The prototype developed in the present study was made of commercial electric parts, and thus it was possible to improve the overall radiation tolerance at a relatively low cost. Also, it was easy to manufacture because there are few constraints for optical design.

• Korean Journal of Optics and Photonics
• /
• v.16 no.1
• /
• pp.13-20
• /
• 2005

Fiber-Bragg-grating external cavity laser(FGL) modules were fabricated and experimentally analyzed. Proposed as a cost-effective solution for optical sources in the WDM-PON access network, FGL modules were packaged to TO-CAN type. We obtained a low threshold current of 13 mA, and an optical output power of 3.6 mW with a bias current of 60 mA at $25^{\circ}C$. The lasing wavelength dependencies on current and temperature were as small as 5.2 pm/mA and 30 pm/$^{\circ}C$, respectively. These change rates of the wavelength with the temperature and current are smaller than those of the DFB laser. Single-mode oscillations with the side-mode suppression ratio(SMSR) over 30 dB are maintained above the threshold current level. The FGL modules can be directly modulated at 155 Mbps, PRBS(2$^{23}$ -1) NRZ signal. Through the BER plots, we did not see the significant degradations before and after the transmission over 20km of the SMF at 155 Mb/s.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.7
• /
• pp.701-706
• /
• 2015

In this study, experimental and computer simulation results are compared and analyzed. Three-dimensional (3D) fabricated matrices from an MJM 3D printer were joined with poly-acetate thermoplastic polymers using a diode laser. A power range of 5-7 W was used to irradiate the boundary of two polymers. The heated polymers flowed into the matrices of the 3D fabricated structure, and reliable mechanical joining was achieved. Computer simulation showed the temperature distribution in the polymers, and flow direction was estimated based on the flux and temperature information. It was found that the more than the minimum energy threshold was required to effectively join the polymers and that two scans at low-speed were more effective than four scans at high speed.