• 비파괴검사학회지
• /
• 제23권3호
• /
• pp.205-211
• /
• 2003

구조물의 안전성평가와 관련하여 비파괴평가 방법 중에서 음향방출 (acoustic emission, AE)기법에 의한 비파괴적 결함 발생 검출 기법은 다른 기법에 비해 비교적 새로운 평가기술로서 구조물의 이상 유무를 조기에 진단하고 주기적으로 감시할 수 있는 온-라인 모니터링에 적합하다. 그러나 한편, 국내에서는 아직까지 이에 대한 체계적인 연구가 미비한 실정이며, 대부분 값비싼 외국 시스템을 도입하여 사용하고 있는 실정이다 뿐 만 아니라 기존의 음향방출 시스템은 장치의 특성상 시스템이 매우 복잡하고 가격이 고가인 관계로 다양한 산업분야에서 실제 현장에 적용하기가 쉽지 않다. 따라서 본 연구에서는 기존의 음향방출 시스템이 가지고 있던 불필요한 낭비적인 요소들을 제거하고 실제 산업현장에 부합하는 위치표정 시스템을 개발하고자 하였다. 한편, 기존의 AE 시스템들은 위치표정을 위한 신호분석이 난해할 뿐만 아니라 박판 구조물의 경우는 위치표정이 매우 어렵다. 본 연구에서는 시간-주파수 해석에 널리 사용되고 있는 웨이블릿 기법을 이용하여 보다 정확한 위치표정을 진단하는 기법을 수행하였다.

• Bulletin of the Korean Chemical Society
• /
• 제19권9호
• /
• pp.927-933
• /
• 1998

Polycrystalline powder of vanadium-doped forsterite (Vδ $Mg_2SiO_4$) was synthesized by the $H_2O_2$-assisted sol-gel method. The vanadium dopant, which was added as VO$(OMe)_3$ in methanol, went through several redox reactions as the sol-gel reaction proceeded. Upon adding VO$(OMe)_3$ to a mixture of $Mg(OMe)_2$ and Si$(OEt)_4$ in methanol, V(V) reduced to V(IV). As hydrolysis reaction proceeded, the V(IV) oxidized all back to V(V). Apparently, some of the V(V) reduced to V(IV) during subsequent gelation by condensation reaction. The V(IV) remained even after heat treatment of the gel in highly oxidizing atmosphere. The crystallization of the xerogel around 880 ℃ readily produced single phase forsterite without any minor phase. Using the polycrystalline powder as feeding stock, single crystals of vanadium-doped forsterite were grown by the floating zone method in oxidizing or reducing atmosphere. The doping was limited in low level because of the high partitioning of the vanadium in liquid phase during melting. The greenish single crystal absorbed visible light of 700∼1100 nm. But, no emission was obtained in near infrared range.

• 설비공학논문집
• /
• 제25권9호
• /
• pp.506-515
• /
• 2013

The PFT (PerFluorocarbon Tracergas Technique) is of advantage to field surveys for evaluating the ventilation condition, due to its simplicity and convenience. On the other hand, it requires researchers to make some additional considerations that include uncertainties, such as the substance concentration distribution in indoor air, representativeness of a sampler, deviation of emission sources, and analysis error. In this study, the PFT and $CO_2$ tracer gas methods were applied simultaneously, to evaluate the accuracy of PFT on six ventilation conditions in the three-storied detached house. The air exchange and the outdoor air introduction a between and into zones were measured. As the results, deviations of PFT concentration distributions were observed at a sufficiently low level for an accurate determination for a house where the interior height was large, and there were relatively many partition walls. However, when a uniform airflow appeared in the indoor air, it was also validated that the indoor air would be exhausted without sufficient mixing, and consequently the measurement error of the PFT would be large.

• 설비공학논문집
• /
• 제28권7호
• /
• pp.275-282
• /
• 2016

MILD (Moderate and Intense Low-oxygen Dilution) combustion using oxygen as an oxidizer is considered as one of the most promising combustion technologies for high energy efficiency and for reducing nitrogen oxide and carbon dioxide emissions. In order to investigate the effects of nozzle angle and oxygen velocity conditions on the formation of oxygen-MILD combustion, numerical and experimental approaches were performed in this study. The numerical results showed that the recirculation ratio ($K_V$), which is an important parameter for performing MILD combustion, was increased in the main reaction zone when the nozzle angle was changed from 0 degrees to 15 degrees. Also, it was observed that a low and uniform temperature distribution was achieved at an oxygen velocity of 400 m/s. The perfectly invisible oxy-MILD flame was observed experimentally under the condition of a nozzle angle of $10^{\circ}$ and an oxygen velocity of 400 m/s. Moreover, the NOx emission limit was satisfied with NOx regulation of less than 80 ppm.

• 한국대기환경학회지
• /
• 제18권2호
• /
• pp.85-94
• /
• 2002

In this study, a 3-dimensional numerical model, has been developed applied for the investigation of combustion characteristics, and used to optimize operating conditions in MSW incinerator, in Gwangju. The model developed in this study has been verified by exacting both the predicted and the measured temperature in combustion chamber which has been operated to provide a reference condition. By predictive results, the Sangmoo incinerator has a good characteristics of combustion and low emission however after burning zone produced incomplete products, also probably because the supply of primary air was not enough. Parametric screening studies have been conducted to study optimal operating conditions. For the optimal combustion characteristics, operating conditions should be adjusted with the waste properties.

• 연구논문집
• /
• 통권31호
• /
• pp.23-43
• /
• 2001

An experimental investigation on the reduction of nitrogen oxide emission from swirling, turbulent diffusion flames was conducted using multi air staged combustor, The combustor utilizes swirler to dampen fuel/air mixing, allowing an extended residence time for fuel pyrolysis and fuel-N conversion chemistry in an locally fuel-rich environment prior to burnout. This process also allow to reduce thermal NOx formation to lessen the temperature of reaction zone. The aerodynamic process therefore emulates the conventional staged combustion process, but without the need for the physically separate fuel-rich and -lean stages. Parametric studies on the ratios of each staged air and droplet size were carried out the feasibility of fuel/air mixing for low NOx combustion with diesel and pyridine mixed diesel fuel oil.

• 한국안전학회지
• /
• 제9권1호
• /
• pp.9-18
• /
• 1994

In this study, we conducted experimental tests to evaluate fracture behaviors of fresh-butt welded metal by Acoustic Emission technique. We selected similar welding and dissimilar welding process, the one welded for SM45C, SS41 and SUS304 of each material, the other for SM45C and SS41, SM45C and SUS304 and SS41 and SUS304. The fracturing processes of weld metal were estimatied through the fracture toughness test with compact tension specimens and fractography analysis. In ASTM test method E-399, type I curves for materials of this study were obtained by load-cod diagram of fracture toughness test. and 5% offset load( $P_{5}$) was estimated as the estimated crack initial load( $P_{Q}$), The estimated crack initial load( $P_{Q}$) of similar welding materials generally lower than base matal, and then SM45C appeared greatly in decreasing rate of PB, SS41 and SUS304 appeared in order. $P_{Q}$ of dissimilar welding materials were lower than the similar welding materials. $P_{Q}$ of welding of SM45C and SS41 appeared in small, SUS304 and SS41 appeared greatly in dissimilar welding materials. In fracture toughness test, AE counts increased before the inflection point of the slope, decreased after that. It was found that increasing of AE counts were due to the microcrack formation at the crack tip near the $P_{5}$ point through AE data. For welding materials in this study, both low and high AE amplitude appeared simulataneously. It was confirmed that the low AE amplotude was due to formation of micro void, micro crack or micro dimple, the high AE amplitude was caused by microvoid coalescence and quasi-cleavage fracture through analyses of fractograpy.apy.apy.apy.

• 비파괴검사학회지
• /
• 제23권5호
• /
• pp.429-438
• /
• 2003

본 연구에서는 연속형 일방향 및 수자직 유리섬유강화 복합재료로 인장 시험편을 만들어 AE 특성에 대한 섬유배향 효과를 살펴보았다. AE 신호들을 STFT 처리하여 특성별로 분류하였으며, 반사식 및 투과식 편광현미경을 이용하여 시험편의 손상영역을 관찰하였다. 저주파수 대역의 약한 AE 신호들은 모재 및 계면에서의 손상으로 나타났으며, 높은 진폭의 고주파수 대역 AE 신호들은 섬유 파단에 기인하였다. 섬유 파단 과정에서 발생하는 고진폭의 AE 사상률을 기본 특성 데이터로 하여 다른 섬유배향과 노치방향을 가진 복합재에서의 파괴과정을 특징지을 수 있었다. 결론적으로, AE범은 연속형 유리섬유 강화 복합재의 파괴거동을 탐지하는데 있어 유용함을 알 수 있었다.

• 비파괴검사학회지
• /
• 제23권3호
• /
• pp.246-253
• /
• 2003

항공기 구조를 모사하여 일련의 리벳 구멍을 갖는 AA2024-T3 박판 구조를 대상으로 피로하중에 의한 단균열(short crack)의 발생시점과 성장거동을 음향방출(AE)을 위주로 한 측정으로 평가하였다. AE 위치표정에 의해 단균열의 좌표를 정확하게 결정하였으며, 이동식 현미경으로 균열의 크기를 측정하였다. 누적 AE 발생수 곡선은 단균열의 발생과 성장에 따라 일정한 간격을 두고 급격히 증가하는 양상을 보임으로써 여러 차례의 계단식 곡선을 형성하였다. AE 위치표정에서는 리벳 구멍을 중심으로 파괴역학에 근거한 관심영역(ROI)을 설정하였으며, 웨이블릿변환 잡음제거 방법을 사용하여 위치표정의 정확도를 향상할 수 있었다. 실제로 탐지된 신호의 대부분이 단 균열의 발생 및 성장과 관계없는 외부 잡음신호로 나타났으며, ROI 내에서 발생한 AE 발생원의 위치도 구조의 기하학적 특징이나 신호대잡음비의 영향에 의해 왜곡될 수 있음을 알 수 있었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2010년도 춘계학술대회 논문집
• /
• pp.745-755
• /
• 2010

GTX(Great Train Express), the wide area express train of a big city center of metropolitan area, is the best new transportation method able to realize 'Low Carbon Green Growth' for solving traffic congestion of the metropolitan area with the connection the metropolitan area into 40-minute life zone by speeding up the standardized velocity, making the route straight and reducing the compensation of land using the space of 40~50m below the ground. In the transportation sector all over the world, if it turned into the public transportation system focusing on the train at a point of time that low carbon green revolution takes the initiative, national competitiveness would be enhanced by reducing the emission of carbon from cars by 1/6. Accordingly, this study is to look into the efficient operation in accordance with GTX construction superintended by currently Gyeonggi province and to consider the optimum operation plan of GTX that are proper for the actual circumstances of the country by comparatively analyzing overseas cases that took their positions as new transportation by curtailment of transit time through highspeed such as London area, Paris area, and Tokyo area etc that are similar to Korean metropolitan area.