• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.2439-2442
• /
• 2000

This paper presents a practical On-The-Fly(OTF) integer ambiguity resolution algorithm for real-time precise positioning with low cost, $L_1$ single frequency, conventional C/A code GPS receiver. A state reconfiguration scheme is adopted in the Kalman filter to deal with the variation of ambiguity states caused by varying sets of visible GPS satellites. The proposed algorithm reduces the ambiguity search space from the coarse m-level C/A code pseudorange measurements of the conventional C/A code reciever, thereby reducing the computational time. Simulation results are presented to show that the algorithm achieves a cm-level accuracy.

• Journal of Information Processing Systems
• /
• v.11 no.3
• /
• pp.342-353
• /
• 2015

It is widely accepted that single carrier frequency division multiple access (SC-FDMA) is an excellent candidate for broadband wireless systems. Channel estimation is one of the key challenges in SC-FDMA, since accurate channel estimation can significantly improve equalization at the receiver and, consequently, enhance the communication performances. In this paper, we study the application of compressive sensing for sparse channel estimation in a SC-FDMA system. By skillfully designing pilots, their patterns, and taking advantages of the sparsity of the channel impulse response, the proposed system realizes channel estimation at a low cost. Simulation results show that it can achieve significantly improved performance in a frequency selective fading sparse channel with fewer pilots.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.139-140
• /
• 2010

This paper presents an indoor prototype for wireless digital signal transmission using Visible Light Communications (VLC) in which high power Light Emitting Diode (LED) is used. Using low cost and off-the-shelf components, the transmitter module is constructed using an AVR Atmega128 microcontroller and commercial white beam LEDs. Modulating the light intensity of the LED enables digital signals to be transmitted across the optical link. The receiver module employs a high speed PIN photodetector for optical signal detection and a recovery circuit for optical-electro signal conversion. By sending digitalized data via VLC technology, many applications can be realized in the areas of consumer advertising, traffic safety information and disaster control.

• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.2
• /
• pp.127-134
• /
• 2022

In this paper, a low-cost, flexible GPS simulator based on USRP is designed as a general-purpose software wireless front-end. The simulator consists of a software GPS signal generator and a USRP-based RF transmitter. The simulator supports various scenarios including specified reception time, quantization bit level, I/Q data types, IF frequency, sampling frequency, SNR, ionospheric delay and user dynamics. The generated GPS RF signal is verified using the spectrum analyzer and off-the-shelf GNSS receivers such as U-blox M8T. The experimental results shows that the difference between generated and real live signal is ignorable. It is expected that designed GPS simulator can be used to GNSS signal design, receiver design and signal processing algorithms such as anti-jamming.

• International Journal of Internet, Broadcasting and Communication
• /
• v.14 no.3
• /
• pp.63-68
• /
• 2022

Two wavelength reconfigurable optical nodes are designed. One for 20km or shorter link length, and the other for up to 60km link length. While the first one requires no dispersion compensation, the latter needs dispersion compensation fiber included in the node, which requires additional optical amplifier to compensate the insertion loss of DCF. We calculate all the optical path losses in both cases using the typical value of optical components in the market to see the feasibility of the designed optical node. The minimum received power in the node is calculated to be -21.5dBm without DCF and -12.5dBm with DCF, respectively. These received powers are above the receiver sensitivity both for OC-48 and OC-192 according to the previous work.

• International Journal of Computer Science & Network Security
• /
• v.23 no.2
• /
• pp.140-146
• /
• 2023

With the rapid growth of new users and massive need for very high data rate in 5G communications system, different technologies have been developed and applied to enhance communication efficiency. One of those technologies is the MISO, MISO and MIMO which transmits and receives information with more reliability by using multiple antennas on transmitter or/and receiver side. This paper presents the latest trends in 5G telecommunications system based on software defined radio, A novel low-cost SIMO, MISO and MIMO using flexibility between USRP and Simulink is implemented tested and validated.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.9
• /
• pp.883-891
• /
• 2013

In wireless smart phone charging scenario, the transmitter pad is larger than the size of the receiver pad. Thus, it is important to supply a constant power to the receiver regardless of its location. In this paper, we propose a new method to regulate the receiver's power by adjusting a drain bias of class E power amplifier. The proposed LF-band wireless power transfer system is as follows: a buck converter power supply which is controlled by a pulse width modulation(PWM) IC TL494, a class E amplifier using a low cost IRF510 power MOSFET, a transmitter coil whose dimension is $16cm{\times}18cm$, a receiver coil whose dimension is $6cm{\times}8cm$, and a full bridge rectifier using Schottky diodes. A measured performance show a maximum output power of 4 W and system efficiency of 67 % if we fix the bias voltage. If we adjust the bias voltage, the received power can be maintained at a constant power of 2 W regardless of receiver pad location.

• Journal of Information Technology Applications and Management
• /
• v.26 no.6
• /
• pp.103-117
• /
• 2019

Demand for high power motors is rapidly increasing as the 4th industry and convergence technology has recently emerged. In order to produce high-strength permanent magnets, the magnets used for magnetization have been increased from DC 300V in the 1970s to DC 2.5kV in the 2010s, Up to DC 10kV in the 2030s, It is expected that higher voltage will be used to magnetize. However, in the case of a magnetizer using an existing electric signal control device, it is necessary to use a control device with a high-voltage insulation function in case a high voltage used for magnetization is leaked to the control device. If a short circuit accident occurs, the controller must be shut down and serious problems such as excessive repair costs arise. In this study, a control system adopting optical communication method instead of electric signal control method is proposed to prevent leakage currents in high-voltage magnetizer. We design a transmitter(Tx) and a receiver(Rx) device for the optical communication control device and implemented a prototype connecting the optical cable. In order to demonstrate the utility of high-voltage magnetizer using the optical communication control device, we analyzed the initial cost and the yearly cost for the years to analyze the net present value. As a result, In the case of the low-voltage magnetizer, the electric signal control method cost less, As the operating voltage of the magnetizer becomes higher. It is confirmed that it takes less cost when the optical communication control device is used.

• ETRI Journal
• /
• v.37 no.1
• /
• pp.32-42
• /
• 2015

Orthogonal frequency-division multiplexing (OFDM) suffers from spectral nulls of frequency-selective fading channels. Linear precoded (LP-) OFDM is an effective method that guarantees symbol detectability by spreading the frequency-domain symbols over the whole spectrum. This paper proposes a computationally efficient and low-cost implementation for discrete Hartley transform (DHT) precoded OFDM systems. Compared to conventional DHT-OFDM systems, at the transmitter, both the DHT and the inverse discrete Fourier transform are replaced by a one-level butterfly structure that involves only one addition per symbol to generate the time-domain DHT-OFDM signal. At the receiver, only the DHT is required to recover the distorted signal with a single-tap equalizer in contrast to both the DHT and the DFT in the conventional DHT-OFDM. Theoretical analysis of DHT-OFDM with linear equalizers is presented and confirmed by numerical simulation. It is shown that the proposed DHT-OFDM system achieves similar performance when compared to other LP-OFDMs but exhibits a lower implementation complexity and peak-to-average power ratio.

• Journal of Communications and Networks
• /
• v.15 no.5
• /
• pp.496-503
• /
• 2013

In an orthogonal frequency division multiplexing system, conventional interpolation techniques cannot correctly balance performance and overhead when estimating dynamic long-delay channels in single frequency networks (SFNs). In this study, classical filter analysis and design methods are employed to derive a complex interpolator for maximizing the resistible echo delay in a channel estimator on the basis of the correlation between frequency domain interpolating and time domain windowing. The coefficient computation of the complex interpolator requires a key parameter, i.e., channel length, which is obtained in the frequency domain with a tentative estimation scheme having low implementation complexity. The proposed complex adaptive interpolator is verified in a simulated digital video broadcasting for terrestrial/handheld receiver. The simulation results indicate that the designed channel estimator can not only handle SFN echoes with more than $200{\mu}s$ delay but also achieve a bit-error rate performance close to the optimum minimum mean square error method, which significantly outperforms conventional channel estimation methods, while preserving a low implementation cost in a short-delay channel.