• 미생물학회지
• /
• 제6권2호
• /
• pp.54-62
• /
• 1968

The effect of gamma-ray on yeast cells Sacch. cerevisiae, and the leakage of cellular constituents such as carbohydrates, ribose, amino acids, inorganic phosphates and organic phosphates have been studied. The samples of yeast cells washed throughly and starved intensively, radiation effects were compared with those of control (un-starved), the irradiation dose rates are in the range from 24 Kr. up. to 480, Kr. The loss of 260m$\mu$. absorbing material, are also observed. Mechanisms of membrane damage by gamma-irradiation are discussed corelating to permeability changes and loss of substances, then active and passive transport process are also under considerations in discussion. The experimental results are as follows, 1. Carbohydrates of yeast cell leak out by gamma-irradiation, and amounts of loss increase proportionally as the increasing of radiation dose, curve of carbohydrates loss in starved cells is parallel with those of non-starved cells. 2. Ribose leak out less than that of carbohydrate from irradiated cell, the dose response curve of loss is straight and proportional to the increasing of radiation doses, slope of the curve is much lower than of carbohydrates. 3. Amino acids also leak out and the curve of losses to radiation is not proportional, it is revealed that there are little losses from yeast at lower doses of irradiation. 4. The losses of inorganic phosphates increase unproportionally to the increasing of irradiation doses, there are little leakage at the lower doses of irradiation. The losses of organic phosphates increase proportionally to the increasing of irradiation doses, and the amount of losses are much more than that of inorganic phosphate at lower doses of irradiation. 5. Leakage from irradiated yeast cells was shown to be due to passive transport process not an energy requiring process of ion transport. 6. Loss of 260 m$\mu$. absorbing material is little more than that of control yeast by the gamma-irradiation dose of 120K.r. and 240K.r.

• 전자공학회논문지CI
• /
• 제39권5호
• /
• pp.21-31
• /
• 2002

MPEG 스트리밍 트래픽이 인터넷을 통해서 서비스되어질 때 발생하는 MPEG 비디오 패킷 손실은 영상의 공간적인 그리고 시간적인 에러의 전파 현상을 일으키며, 영상 품질의 심각한 저하를 가져온다. 이러한 영상의 열화 현상은 망에서 패킷의 버스트 손실 특성에 의하여 더욱 더 악화되어진다. 본 논문에서는 버스트 패킷 손실의 영향을 줄일 수 있는 새로운 에러 확산 기법을 제안한다. 제안하는 에러 확산 기법은 국부적으로 발생하는 패킷 손실을 효과적으로 넓은 영역에 분포시킬 수 있으며, videocasting이나 video-broadcasting 분야와 같은 ARQ의 사용이 제한되는 응용 서비스에서 이용될 수 있다. 결과적으로 연속적으로 발생하는 이미지 블록 손실 현상이 줄어들게 되며, 에러 은닉 기법의 성능을 향상시킬 수 있다. 실험 결과는 제안된 에러 확산 기법에 의해 MPEG 패킷 손실이 확산되어 비디오 품질의 열화 현상이 개선될 수 있음을 보이고 있다.

• 한국산림과학회지
• /
• 제3권1호
• /
• pp.5-9
• /
• 1963

1. Creosote in treated wood that exposed in open areas of outdoor is gradually lost by elapse of some period of time. This is the interst and important problem relating to decide the effect on the life extension of creosoted wood. As a general preservative losses occurring in wood treated by oil born preservative such as creosote oil are taken place boy the evaporating and washing activities of the exposed surfaces of wood due to the climatic conditions. Accordingly author intend to inspect differences in retention among species showing after creosoted blocks had been treated by evaporating and washing alternately for a definite time in the laboratory. 2. In this study rail road tie woods of Quercus aliena Blume, Fagus crenata Blume and Fraxinus mandchurica Ruprecht which entered into area for treatment at the plant, locating in Suwon, Korea, were selected to the test species. $2{\times}2{\times}2$ centimeter forty small wood blocks for each species were cut, treated by the mixed solution of equal 50% creosote and heavy oil (hot and cold method), and inspected absorption percents. After evaporation and washing treatments alternately to the intervals of definite time had been accomplished, the losses of creosote were inspected. 3. According to the results Quercus Fagus and Fraxinus are showing the values of 37.9, 87.3 and 59.3% in absorption, and these values were reduced into 28.7, 63.8 and 44.4% respectively by evaporating and washing treatments for a definite time. These indicate that losses of ease absorbing species are greater than difficult one and on the contrary difficult are lesser. However above reduced values are calculated to the 24.3, 26.9 and 25.1% when the absorption percents of each species were assumed as 100% retention respectively. Therefore actual differences of losses among species are lesser than those of absorption percents.

• 한국초등수학교육학회지
• /
• 제21권3호
• /
• pp.505-530
• /
• 2017

본 연구는 수학영재의 집단창의성 발현 과정과 산출을 분석하여 어떤 특성이 있는지를 확인하고, 집단창의성 발현을 방해하는 과정 손실의 원인을 파악하는 것을 목적으로 하였다. 이를 위해 수학영재학급 수업에 집단창의성 발현을 위한 단계를 적용하였고, 수 체계의 성질과 모듈로 산술을 주제로 하여 수업을 진행하였다. 연구방법으로는 학생들이 보인 반응과 산출의 사례를 질적으로 분석하는 사례연구를 진행하였고, 집단창의성 발현 과정과 산출, 과정 손실의 원인에 대한 선행연구 내용을 기준으로 분석하였다. 그 결과, 집단의 과정에서 창의적 시너지가 나타날 수 있는 상보적, 발생, 긴장 상태와 기여의 결합이 나타나는 방식인 수집, 연결, 선택, 변형, 집단의 창의적 산출의 특성인 집단 유창성, 집단 융통성, 집단 독창성, 집단 정교성이 관련된 것끼리 이어질 수 있음을 확인하였다. 그리고 집단 수준의 창의적 시너지가 나타날 수 있는 상보적, 발생, 긴장 상태에서 과정 손실의 인지적 원인과 사회 동기적 원인이 나타나는 경우를 확인하였다. 분석 결과를 통해 집단창의성 발현을 위한 수학영재학급 수업 설계 시에 고려해야 할 점에 대해 제안하였다.

• 대한환경공학회지
• /
• 제32권4호
• /
• pp.357-362
• /
• 2010

미생물연료전지는 미생물이 유기물을 분해하면서 전기를 발생시킨다. 미생물연료전지는 여러 분야로 응용이 가능하며 현재 생산되는 전력이 낮기 때문에 상용화가 되기 위해서는 미생물연료전지(MFC)의 전력을 증진시키는 방안 연구가 필요하다. 미생물연료전지(MFC)의 전력을 증진시키기 위해서는 산화, 환원전극에서의 활성화전압손실(Activation losses)과 저항전압손실(Ohmic losses)을 줄여야 하며 활성화전압손실과 저항전압손실의 정확한 측정과 이를 줄이기 위한 인자를 찾는 것이 중요하다. 본 연구에서는 H형태의 미생물연료전지(Microbial Fuel Cell, MFC)에서 전류차단법(Current interruption)을 이용하여 산화전극 및 환원전극에서의 활성화 전압손실과 저항전압손실을 측정하였다. H형태의 미생물연료전지에서 백금이 코팅된 전극(0.5 $mg/cm^2$; 10% Pt)을 환원전극으로 이용하였음에도 환원전극 전압손실이 산화전극 전압손실보다 4배 가량 큼을 알 수 있었다. 전류차단법(Current interruption)에 의하여 구한 저항전압손실 값(1146 ${\Omega}$) 과 impedance에 의하여 구한 내부저항(1167 ${\Omega}$)은 거의 일치하였다. 또한 산화, 환원전극 활성화 전압손실의 합은 전지(cell)의 활성화 전압손실과 일치하였다.

• 한국농공학회지
• /
• 제15권1호
• /
• pp.2853-2877
• /
• 1973

Models of cross-sections and channels were made in order to measure seepage losses. Cross-sections were made of sand, sandy clay loam and loam, their thicknesses being 30cm and 40cm, respectively. Flow depths kept in the cross-sections were 4cm, 6cm, 8cm and 10cm. Straight and curved channel models were provided so as to measure seepage losses, when constant water depths maintained at the heads of the channels were 7.3cm and 5.7cm, respectively. The results obtained in this experiment are presented as follows: 1) A cumulative seepage loss per unit length at a point in the channel varies in accordance with time and flow depth. The general equation of cumulative seepage loss may be as follows(Ref. to Table V.25): $$q_{cum}=\int_{o}^aq(a)dt+\int_a^bq(b)dt+\int_b^tq(c)dt$$ 2) In case that the variation of water depth through the channel is slight, the total seepage loss may be computed by applying the following general equation: $$\={q}_{cum}{\cdot}x=\int_o^tq_{cum}\frac{{\partial}x}{{\partial}t}dt$$ 3) Because seepage loss varies considerably according to water depth in case that the variation of flow depth through the channel is great, seepage loss should be computed by taking account of the change of flow depth. 4) The relation between time and traveling distance of water flow may be presented as the following general equation(Ref. to Table V.29): $$x=pt^r$$ 5) The ratios of the seepage losses of the straight channel to the curved channel are 1:1.03 for a flow depth of 7.3cm and 1:1.068 for that of 5.7cm. 6) The ratios of the seepage losses occurring through the bottom to those through the inclined plane in the channel cross-section are 1:2.24 for a water depth of 8cm and 1:2.47 for a depth of 10cm in case that soil-layer is 30cm in thickness. Similarly, those ratios are 1:2.62 and 1:2.93 in case of a soil-layer thickness of 40cm(Ref. to Table V.5).

• 한국기계가공학회지
• /
• 제17권5호
• /
• pp.30-36
• /
• 2018

Automotive fuel efficiency regulations and air pollution control are hot issues of recent years in the automotive industry. To solve these regulation problems, many studies are continuing to improve the transmission efficiency of transmissions. Tapered roller bearings are useful to improve the transmission efficiency in the recent automobile parts. The frictional losses in the tapered roller bearings are mainly composed of the rolling friction and the sliding friction, and are dependent upon the load, the lubrication, the rotation speed of bearings, and etc. In this paper, the operating conditions of the transmission are defined and then the power losses of each bearing are calculated. In addition, improvement options are suggested after identifying the design factors influenced much by the improvement effect of power loss under the operating conditions of each bearing. We compare the power losses of the entire transmission system due to bearing improvements by comparing the friction losses between the original design and the improved design. Lastly, it is shown that the calculated power losses are valid by comparing the test values and the theoretical values for the frictional torque characteristics of the original and improved bearings.

• 디지털융복합연구
• /
• 제16권11호
• /
• pp.267-274
• /
• 2018

본 연구는 경영자능력이 한국채택국제회계기준 도입 이후 영업권손상차손 인식에 있어서 경영자의 기회주의적인 재량적 재무보고에 대하여 어떤 영향을 미치는 가를 실증적으로 분석하였다. 2011년~2014년 사이에 영업권을 인식한 1,482개 기업-년 표본을 대상으로, 영업권손상차손을 종속변수로, 영업권손상징후와 경영자능력, 이익조정 관련 변수들을 독립변수로 포함하여 회귀분석을 수행하였다. 분석결과, 경영자능력이 높은 경우, 손상징후에 따라 영업권손상차손이 보다 적절히 인식되고 있으며, 손상차손을 이익유연화 수단으로 이용되는 정도가 감소하였다. 본 연구는 영업권손상차손의 인식에 있어서 경영자의 기회주의적인 재무보고 성향이 경영자능력에 따라 달라질 수 있음을 보여주는 첫 번째 실증분석으로 연구의 유용성이 있으며, 향후에는 경영자능력이나, 영업권손상 징후, 그리고 이익조정 측정방법에 대한 보다 심층적인 연구를 통해 본 연구의 결과를 다양한 연구주제로 확장시킬 수 있을 것이다.

• International Journal of Computer Science & Network Security
• /
• 제21권5호
• /
• pp.57-68
• /
• 2021

Successfully adapting to digital and customer-oriented transformation, the concept of lean manufacturing professes the philosophy of creating greater benefit while minimizing losses. These losses are operations that do not add value in the production process to ensure the efficiency, flexibility, and profitability of projects. In the context of broad automation and digitalization of all sectors of the economy, mechanisms for combining automation technologies and lean production are becoming available. Moreover, when it comes to the efficient use of financial, human, or material resources, it is clear that the use of Industry 4.0 technologies can be an effective tool for achieving the goals of lean production, as many of them pursue the same goal. In this context, this article aims to study the effectiveness of the implementation of project management concepts at the global level and identify the main factors influencing its effectiveness to ensure the achievement of lean production through LEAN technologies and Industry 4.0 technologies. To achieve this goal, several statistical indicators were selected and several statistical methods of analysis were used: pairwise correlation, regression analysis, methods of comparison, synthesis, and generalization. Statistical analysis was conducted according to a survey conducted by the Project Management Institute (PMI) in 2020. An economic-mathematical model of dependence of project effectiveness in different regions of the world on the level of implementation of project management approaches is built, which shows that the increase in project effectiveness by 85% is due to financial losses, technical training, and consumer orientation. These results allow project managers to develop appropriate strategies to improve project management approaches at all levels. It is established that LEAN technologies and technologies of Industry 4.0 have several tools that have a positive effect on minimizing losses following the concept of lean production. Besides, given that the technology of Industry 4.0 is focused on the automation of Lean Production technology, a mechanism for the introduction of lean production using these technologies and methods.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권3호
• /
• pp.272-276
• /
• 2005

This paper deals with the method to calculate the rotor eddy current losses of permanent magnet high-speed machines considering the effects of time/space flux harmonics. The flux harmonics caused by the slot geometry in the stator is calculated from the time variation of the magnetic field distribution obtained by the magneto-static finite element analysis and double Fast Fourier Transform. And, using the analytical approach considering the multiple flux harmonics and the Poynting vector, the rotor losses is evaluated in each rotor composite. Using this method is simple and workable for any kind of stator slot shape for rotor loss analysis.