• Journal of Korean Neurosurgical Society
• /
• 제60권2호
• /
• pp.262-268
• /
• 2017

Objective : Stents are widely used in coil embolization of intracranial aneurysms, but on occasion, a microcatheter must traverse a stented segment of artery (so-called trans-cell technique) to select an aneurysm, or double stenting may necessary. In such situations, microguidewire passage and microcatheter delivery through a tortuous stented parent artery may pose a technical challenge. Described herein is a microguidewire looping technique to facilitate endovascular navigation in these circumstances. Methods : To apply this technique, the microguidewire tip is looped before entering the stented parent artery and then advanced distally past the stented segment, with the loop intact. Rounding of the tip prevents interference from stent struts during passage. A microcatheter is subsequently passed into the stented artery for positioning near the neck of aneurysm, with microguidewire assistance. The aneurysm is then selected, steering the microcatheter tip (via inner microguidewire) into the dome. Results : This technique proved successful during coil embolization of nine saccular intracranial aneurysms (internal carotid artery [ICA], 6; middle cerebral artery, 2; basilar tip, 1), performing eight trans-cell deliveries and one additional stenting. Selective endovascular embolization was enabled in all patients, resulting in excellent clinical and radiologic outcomes, with no morbidity or mortality directly attributable to microguidewire looping. Conclusion : Microguidewire looping is a reasonable alternative if passage through a stented artery is not feasible by traditional means, especially at paraclinoid ICA sites.

• Korean Chemical Engineering Research
• /
• 제46권6호
• /
• pp.1057-1062
• /
• 2008

기존 2탑 유동층 공정의 단점을 극복하기 위해 두 개의 기포유동층, 고체분사노즐, 상승관 및 고체재순환관으로 구성된 신개념 2탑 유동층 공정을 적용한 3 kW 매체순환식 가스연소기를 개발하였다. 본 연구에서는 3 kW급 매체순환식 가스연소기에서 고체순환속도에 미치는 고체분사노즐 유속, 유동화속도, 고체층 높이, 고체유입구의 단면적, 층 온도 등의 영향을 고찰하였다. 고체순환속도는 고체층 높이가 증가하고 고체유입구의 단면적이 증가할수록 증가하는 경향을 나타내었으며 유동화속도와 온도의 영향은 크지 않았다. 장기연속운전 가능성을 검토하기 위해 50시간까지 고체순환 장기연속운전을 실증하였다. 두 유동층과 고체재순환관의 압력강하 값이 안정적으로 유지되어 고체순환이 원활하고 안정적으로 유지되는 것을 확인하였다.

• 청정기술
• /
• 제24권1호
• /
• pp.63-69
• /
• 2018

순산소 연소 기술 중 $CO_2$ 회수 비용 절감 효과가 가장 우수한 케미컬루핑연소(chemical looping combustion, CLC) 기술의 핵심인 산소전달입자의 선정을 위해 환원반응 특성 및 물리화학적 특성에 대한 연구를 진행하였다. 세 종류의 산소전달입자(SDN70, N018-R2, N016-R4)를 대상으로 기포유동층 반응기에서 환원반응기체의 농도 및 환원 반응 온도 변화에 따른 산소전달입자의 연료전화율(fuel conversion)과 $CO_2$ 선택도($CO_2$ selectivity)를 측정 및 비교 분석하였다. 또한 산소전달입자의 마모손실 정도 및 입자의 표면 특성을 분석하기 위해 내마모도(Attrition Index, AI) 및 BET surface area를 측정하였다. 결과적으로 세 종류의 산소전달입자 모두 케미컬루핑연소 시스템에 활용하기 적합함을 확인하였으며, 가장 우수한 입자는 N016-R4로 판단되었다.

• 한국수소및신에너지학회논문집
• /
• 제29권6호
• /
• pp.635-641
• /
• 2018

To select the operating condition of 0.5 MWth chemical looping combustion system, minimum fluidization velocity, transition velocity to fast fluidization and solid circulation rate were measured using mass produced new oxygen carrier (N016-R4) which produced by spray drying method for 0.5 MWth chemical looping combustion system. A minimum fluidization velocity decreased as the pressure increased. The measured transition velocity to fast fluidization was 2.0 m/s at ambient temperature and pressure. The measured solid circulation rate increased as the solid control valve opening increased. We could control the solid circulation rate from 26 to $93kg/m^2s$. Based on the measured minimum fluidization velocity and transition velocity to fast fluidization, we choose appropriate operating conditions and demonstrated continuous solid circulation at high pressure condition (5 bar-abs) up to 24 hours.

• 한국수소및신에너지학회논문집
• /
• 제20권3호
• /
• pp.245-255
• /
• 2009

Effect of CO$_2$ concentration on reduction reactivity of oxygen carrier particles for chemical-looping combustor were investigated. Four particles, NiO/bentonite, OCN601-650, OCN702-1100, OCN702-1250, were used as oxygen carrier particles and two kinds of gases (CH$_4$, 5%, N$_2$ balance and CH$_4$ 5%, CO$_2$ balance) were used as reactants for reduction. For all oxygen carrier particles, higher maximum conversion, reduction rate, oxygen transfer capacity, and oxygen transfer rate were achieved when we used N$_2$ balance gas. OCN601-650 particle showed higher oxygen transfer rate for all gases than other particles, and therefore we selected OCN601-650 particle as the best candidate. For all particles, lower carbon depositions were observed when we used CO$_2$ balance gas.

• 한국수소및신에너지학회논문집
• /
• 제28권1호
• /
• pp.85-91
• /
• 2017

To develop a pressurized chemical looping combustor, effect of pressure on minimum fluidization velocity and transition velocity to fast fluidization was investigated in a two-interconnected pressurized fluidized bed system using oxygen carrier particle. The minimum fluidization velocity was measured by bed pressure drop measurement with variation of gas velocity. The measured minimum fluidization velocity decreased as the pressure increased. The transition velocity to fast fluidization was measured by emptying time method and decreased as the pressure increased. Gas velocity in the fuel reactor should be greater than the minimum fluidization velocity and gas velocity in the air reactor should be greater than the transition velocity to fast fluidization to ensure proper operation of two interconnected fluidized bed system.

• 한국수소및신에너지학회논문집
• /
• 제22권2호
• /
• pp.213-222
• /
• 2011

To check adaptability of low ash coal(hyper coal) to chemical looping combustion, reaction characteristics of two coals (Roto and Hyper coal) with two oxygen carriers (NiO/bentonite, OCN703-1100) have been investigated in a thermogravimetric analyzer. Hyper coal represented low combustion rate and high ignition temperature, high volatile content and high devolatilization rate, and therefore, showed worse oxygen transfer during successive 10 cycle reduction-oxidation test than Roto coal. Finally we selected Roto coal as the candidate coal for chemical looping combustion. For Roto coal, OCN703-1100 particle showed better oxygen transfer than NiO/bentonite particle. During 10 cycle reduction oxidation test, change of the extent of oxidation (Wo) was negligible and we could conclude that both oxygen carriers have sufficient regeneration ability.

• 한국수소및신에너지학회논문집
• /
• 제15권3호
• /
• pp.208-219
• /
• 2004

To find a suitable oxygen carrier particle for a 50kW chemical-looping combustor, which was designed and installed to demonstrate continuous oxidation and reduction, three oxygen carrier particles(NiO/bentonite, $NiO/NiAl_2O_4$, $CoO_x/CoAl_2O_4$) were prepared. The reactivity and the attrition resistance of particles were measured and investigated by a thermo-gravimetrical analyzer and an attrition test apparatus respectively. From the viewpoints of oxygen transfer capacity, optimum reaction temperature(operating temperature range), reaction rate, carbon deposition rate, and attrition resistance, NiO/bentonite particle showed better performance than the other particles, therefore we selected NiO/bentonite particle as an optimum oxygen carrier particle.

• 한국수소및신에너지학회논문집
• /
• 제30권2호
• /
• pp.170-177
• /
• 2019

Continuous solid circulation test at high temperature and high pressure conditions and batch type reduction-oxidation tests were performed to check feasibility of a 0.5 MWth chemical looping combustion system. Pressure drop profiles were maintained stable during continuous solid circulation up to 16 hours. Therefore, we could conclude that the solid circulation between an air reactor and a fuel reactor could be smooth and stable. The measured fuel conversion and $CO_2$ selectivity were high enough even at high capacity and even after cyclic tests. Therefore, we could expect high reactivity of oxygen carrier at real operation condition.

• Journal of Ceramic Processing Research
• /
• 제20권1호
• /
• pp.18-23
• /
• 2019

Chemical looping combustion (CLC) is a promising carbon capture and storage (CCS) technology whose efficiency and cost primarily relies on the oxygen carrier materials used. In this paper, gadolinium-doped ceria (GDC, Ce0.9Gd0.1O1.95) was added as a promoter to improve the oxygen transfer rate of MgMnO3-δ oxygen carrier materials. Increasing GDC content significantly increased the oxygen transfer rate of MgMnO3-δ-GDC composites for the reduction reaction due to an increase in the surface adsorption of CH4 via oxygen vacancies formed on the surface of the GDC. On the other hand, the oxygen transfer rate for the oxidation reaction decreased linearly with increasing GDC content due to the oxygen storage ability of GDC. Adsorbed oxygen molecules preferentially insert themselves into oxygen vacancies of the GDC lattice rather than reacting with (Mg,Mn)O to form MgMnO3-δ during the oxidation reaction.