• Journal of the Korean Geotechnical Society
• /
• v.20 no.2
• /
• pp.131-141
• /
• 2004

For geotechnical applications, engineers use data obtained from a site investigation to interpret the structure and potential behavior of the subsurface. In most cases, these data consist of samples that represent 1/100,000 or less of the total volume of soil. These samples and associated field and lab testing provide the information used to estimate soil parameter values. The resulting values are estimated ones and there exists some likelihood that actual soil conditions are significantly different from the estimates. This may be the case even if the sampling and interpretation procedures are performed in accordance with standard practice. Although these efforts have been made to characterize the uncertainty associated with geotechnical parameters, there is no commonly accepted method to evaluate quantitatively the quality of an investigation plan as a whole or the relative significance of individual sampling points or potential sampling points.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.1
• /
• pp.171-178
• /
• 1994

The skin friction on single piles was investigated by using an analytical study and a numerical analysis. The emphasis was given to the variation of skin friction on piles based on the load transfer mechanism developed for the consolidation of a surrounding soft clay. Local yield or slip at the pile-soil interface was taken into account by specifying a limiting value of shear stress. The response of a single pile was analyzed and compared to the results of field case study. Based on the results obtained, it is shown that the skin friction on a pile increases as the degree of consolidation increases and the ultimate axial forces result from the long term behavior of clay corresponding to the end of the consolidation. It is also found that the analysis using one-dimensional consolidation theory as well as two or three-dimensional non-linear analysis gives relatively reasonable results.

• Economic and Environmental Geology
• /
• v.32 no.6
• /
• pp.633-644
• /
• 1999

Gully pot is a part of urban darainage system to butter the runoff water fluxes from road to rivers and to minimize environmental pollution by prevending over the surrounding area. A series of studies have been carried out concerning the physicochemical characteristics of the sewage sludge sediments sttling down in such a gully pot in order to over to evaluate the contamination for heavy metals such as pb, Zn, Cu and Cd. The roadside soil and sewage sludge samples from gully pots were characterized by XRD analyses and sequential extraction : Zn 2595.7$\mu$g/g; Cd9.8$\mu$/g; Cu602.5$\mu$g/g; Pb260.0$\mu$g/g),because of a long-term accumulation of vehicle- and industrial-related pollutants. Mean Zn concentration in Yeouido (3873$\mu$g/g) and Junggu(3262$\mu$g/g)areas are 4-5 times higher than those in Dobonggu area, suggesting that Zn may be derived from automobile traffic (including the rubber of automobile tires). The mean concentrations of Cu and Cr are very significantly high in Junggu and Gurogu areas, possibly due to the industrial activities in these areas. The low Pb levels throughtotut the whole study areas in Seoul can be accounted for the use of unleaded gasoline since 1987. Sequential extraction experiments illustrate that a major part of Zn is bound to FII and FIII, representing about 88% of the total Zn concentration. Fraction IV, related to orgnic matter, is mostly significant for Cu accounting for 60% of the total Cu, and FII is next in importance. The main carriers of Pb are the fractions III, II and FIV, and in that order. The behavior of Cd is quite different from other elements (Zn, Cu, Pb), and most of the Cd is associated with FV. Changes in the physicochemical environments (such as acidification) may result in severe environmental pollution of surface water and rivers with respect to heavy metals (especially Zn and Cu).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.1 no.1
• /
• pp.53-68
• /
• 1981

Most clays under sustained load exhibit time-dependent deformation because of creep movement of soil particles and many investigators have attempted to relate their findings to the creep behavior of natural ground and to the long-term stability of slopes. Since the creep behavior of clays may assume a variety of forms depending on such factors as soil plasticity, activity and water content, it is difficult and complicated to analyse the creep behavior of clays. Rheological models composed of linear springs in combination with linear or nonlinear dashpots and sliders, are generally used for the mathematical description of the time-dependent behavior of soils. Most rheological models, however, have been proposed to simulate the behavior of secondary compression for saturated clays and few definitive data exist that can evaluate the behavior of non-saturated clays under the action of sustained stress. The clays change gradually from a solid state through plastic state to a liquid state with increasing water content, therefore, the rheological models also change. On the other hand, creep is time-dependent, and also the effect of thixotropy is time-function. Consequently, there may be certain correlations between creep behavior and the effects of thixotropy in compacted clays. In addition, the states of clay depend on water content and hence the height of the specimen under drained conditions. Futhermore, based on present and past studies, because immediate elastic deformation occurs instantly after the pressure increment without time-delayed behavior, the factor representing immediate elastic deformations in the rheological model is necessary. The investigation described in this paper, based on rheological model, is designed to identify the immediate elastic deformations and the effects of thixotropy and height of clay specimens with varing water content and stress level on creep deformations. For these purposes, the uniaxial drain-type creep tests were performed. Test results and data for three compacted clays have shown that a linear top spring is needed to account for immediate elastic deformations in the rheological model, and at lower water content below the visco-plastic limit, the effects of thixotropy and height of clay specimens can be represented by the proposed rheological model not considering the effects. Therefore, the rheological model does not necessitate the other factors representing these effects. On the other hand, at water content higher than the visco-plastic limit, although the state behavior of clays is visco-plastic or viscous flow at the beginning of the test, the state behavior, in the case of the lower height sample, does not represent the same behavior during the process of the test, because of rapid drainage. In these cases, the rheological model does not coincide with the model in the case of the higher specimens.

• Tunnel and Underground Space
• /
• v.30 no.1
• /
• pp.39-62
• /
• 2020

In this study, Barcelona Basic Model (BBM) was implemented into TOUGH2-MP/FLAC3D for the numerical analysis of coupled thermo-hydro-mechanical (THM) behavior of unsaturated soils and the prediction of long-term behaviors. Similar to the methodology described in a previous study for the implementation of BBM into TOUGH-FLAC, the User Defined Model (UDM) of FLAC based on the Modified Cam Clay Model (MCCM) and the FISH function of FLAC3D were used to extend the existing MCCM module in FLAC3D for the implementation of BBM into TOUGH2-MP/FLAC3D. In the developed BBM module in TOUGH2-MP/FLAC3D, the plastic strains due to change in suction increase (SI) in addition to mean effective stress are calculated. In addition to loading-collapse (LC) yield surface, suction increase (SI) yield surface is changed by hardening rules in the developed BBM module. Several numerical simulations were conducted to verify and validate the implementation of BBM: using an example presented in the FLAC3D manual for the standard MCCM, simulation results using COMSOL, and experimental data presented in SKB Reports. In addition, the developed BBM analysis module was validated by simultaneously performing a series of modeling tests that were performed for the validation of the Quick tools developed for the purpose of effectively deriving BBM parameters, and by comparing the Quick tools and Code_Bright results reported in a previous study.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.11
• /
• pp.13-19
• /
• 2015

Construction materials using soil which is the most common material around us have many advantages, but their long-term durability and sensation of walking as pavements have problems. Therefore, they are used after compaction or mixed with various hardening agents such as lime and cement for strength enhancement. However, studies on the behavior of pavement materials mixed with environment-friendly hardening agents or admixtures to improve walking property are still insufficient. In this study, therefore, in order to evaluate the appropriate mixing ratio and field application characteristics of pavement materials using mixed soils with environment-friendly hardening agents and natural materials such as wood chips, mechanical tests were performed to evaluate the rational mixing ratios and the ball test was performed as an elasticity test to evaluate the field applicability. The results suggest that the content of wood chips should be selected at 1.5% or lower according to the purpose of the structure, and the hardening agent at 10~15%. The evaluation results for GB/SB coefficient ratio which indicates the walking property show that the appropriate mixing ratio of the hardening agent in terms of the sensation of walking is 15% of lower, but different mixing ratios should be chosen according to the proportion of wood chips.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.37 no.5
• /
• pp.787-799
• /
• 2017

Although the long-term leakage between the box culvert and the soil contact surface is one of the main causes of the failure in the embankment of the reservoir, there is a little studies on this matter. If a leakage occurs by the structure such as the buried box culvert of reservoir embankment is partially damaged, it is difficult to observe and there is a possibility of damage caused by piping. For these reasons, more research is necessary. In this study, the embankment type of the reservoir is divided into the core type and the homogeneous type when the damaged box culvert passing through the embankment of the reservoir is leaked due to the differential behavior of materials like differential settlement. In view of the condition, the seepage analysis of 2D was performed according to the water level change. The result of the study shows that the possibility of piping increases at the upper part rather than the bottom part of the box culvert when the leakage occurs to the box culvert passing through the embankment of the reservoir. Particularly, it is considered that the presence of the core helps to maintain the seepage stability of the embankment in case where the leakage occurs at the downstream side of the embankment. Also, if there is a drastic decrease on the internal pore water pressure in the embankment of reservoir, it is necessary to consider the possibility of piping.