• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.29 no.6
• /
• pp.279-285
• /
• 2017

In general, the power law and logarithmic profile are commonly used as flow vertical velocity profile model. However, since the parameters of profile vary with characteristics of coastal environment, it is necessary to estimate these values from measured data using regression analysis. In this paper, we estimated the power law exponent (n), friction velocity ($u^*$) and roughness length ($z_0$) of logarithmic profile by analyzing measured tidal current data that are averaged at a interval of 30 min. In the results of analysis, power law exponent (n) was estimated to be about 10.75 during flood and about 9.3 during ebb. Meanwhile, $u^*$ of logarithmic profile was estimated to be about 0.084 m/s, 0.105 m/s during flood and ebb, respectively. Also, $z_0$ was estimated to be 0.004 m and 0.006 m, respectively.

• Wind and Structures
• /
• v.19 no.5
• /
• pp.505-522
• /
• 2014

While effects of the atmospheric boundary layer flow on engineering infrastructure are more or less known, some local transient winds create difficulties for structures, traffic and human activities. Hence, further research is required to fully elucidate flow characteristics of some of those very unique local winds. In this study, important characteristics of observed vertical velocity profiles along the main wind direction for the gusty Bora wind blowing along the eastern Adriatic coast are presented. Commonly used empirical power-law and the logarithmic-law profiles are compared against unique 3-level high-frequency Bora measurements. The experimental data agree well with the power-law and logarithmic-law approximations. An interesting feature observed is a decrease in the power-law exponent and aerodynamic surface roughness length, and an increase in friction velocity with increasing Bora wind velocity. This indicates an urban-like velocity profile for smaller wind velocities and rural-like velocity profile for larger wind velocities, which is due to a stronger increase in absolute velocity at each of the heights observed as compared to the respective velocity gradient (difference in average velocity among two different heights). The trends observed are similar during both the day and night. The thermal stratification is near neutral due to a strong mechanical mixing. The differences in aerodynamic surface roughness length are negligible for different time averaging periods when using the median. For the friction velocity, the arithmetic mean proved to be independent of the time record length, while for the power-law exponent both the arithmetic mean and the median are not influenced by the time averaging period. Another issue is a large difference in aerodynamic surface roughness length when calculating using the arithmetic mean and the median. This indicates that the more robust median is a more suitable parameter to determine the aerodynamic surface roughness length than the arithmetic mean value. Variations in velocity profiles at the same site during different wind periods are interesting because, in the engineering community, it has been commonly accepted that the aerodynamic characteristics at a particular site remain the same during various wind regimes.

• New & Renewable Energy
• /
• v.5 no.4
• /
• pp.11-18
• /
• 2009

Wind energy resources are recently considered as an important power generation alternative in the future. The fact that the investment of wind turbine installation continues to increase has motivated a need to develop more widely applicable methodologies for evaluating the actual benefits of adding wind turbines to conventional generating systems. This study is aiming to estimate the future wind resources with various estimation methods. The wind power is calculated at the hub height 75m of 800KW and 1,500KW wind turbines in Wolryong site, Jeju island, South Korea. Three equations - logarithmic, profile, and power law methods are applied for the accurate prediction of wind profile. In addition, yearly wind power can be calculated by using Weibull & Rayleigh distribution. It is found that predicted wind speed is highly affected by friction velocity, atmospheric stability, and averaged roughness length. It is concluded that Rayleigh distribution provides greater power generation than the Weibull distribution, especially for low wind-speed condition.

• Journal of Environmental Science International
• /
• v.21 no.2
• /
• pp.145-152
• /
• 2012

The mean wind speed and turbulence intensity profiles in the atmospheric boundary layer were extracted from a LIDAR remote sensing campaign in order to apply for CFD validation. After considering the semi-steady state field data requirements to be used for CFD validation, a neutral atmosphere campaign period, in which the main wind direction and the power-law exponent of the wind profile were constantly maintained, was chosen. The campaign site at the Pohang Accelerator Laboratory, surrounded by 40~50m high hills, with an apartment district spread beyond the hills, is to be classified as a semi-complex terrain. Nevertheless, wind speed profiles measured up to 100m above the ground fitted well into a theoretical-experimental logarithmic-law equation. The LIDAR remote-sensing data of the sub-layer of the atmospheric boundary layer has been proven to be superior to the data obtained by conventional extrapolation of the wind profile with 2 or 3 anemometer measurements.

• International Journal of Fluid Machinery and Systems
• /
• v.8 no.2
• /
• pp.94-101
• /
• 2015

To investigate the influence of blade profiles on cavitation behavior in impeller of centrifugal pump, a centrifugal pump with five different blade profiles impellers are studied numerically. The impellers with five different blade profiles (single arc, double arcs, triple arcs, logarithmic spiral and linear-variable angle spiral) were designed by the in-house hydraulic design code using geometric parameters of IS 150-125-125 centrifugal pump. The experiments of the centrifugal pump have been conducted to verify numerical simulation model. The numerical results show that the blade profile lines has a weak effect on cavitation inception near blade inlet edge position, however it has the key effect on the development of sheet cavitation in impeller, and also influences the distribution of sheet cavitation in impeller channels. A slight changing of blade setting angle will induce significant difference of cavitation in impeller. The sharp changing of impeller blade setting angle causes obvious cavitation region separation near the impeller inlet close to blade suction surface and much more flow loss. The centrifugal pump with blade profile of setting angle gently changing (logarithmic spiral) has the super cavitation performance, which means smaller critical cavitation number and lower vapor cavity volume fraction at the same conditions.

• Journal of Environmental Science International
• /
• v.18 no.8
• /
• pp.857-865
• /
• 2009

The physical properties of an atmospheric boundary layer in Wolryong, a west coastal region of Jeju, South Korea, in terms of the atmospheric stability and roughness length, is important and relevant to both engineers and scientists. The study is aiming to understand the atmospheric stability around this region and its effect on the roughness length. We calculate the Monin-Obukhov length(L) against 3 typical regions of the atmospheric condition - unstable regime (-5$-0.2{\leq}H/L{\leq}0.2$) and stable regime (0.2

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.33 no.3
• /
• pp.122-130
• /
• 2021

A wind-speed estimation at the arbitrary elevations is key component for the design of the offshore wind energy structures and the computation of the wind-wave generation. However, the wind-speed estimation of the target elevation has been carried out by using the typical functions and their typical parameters, e.g., power and logarithmic functions because the available wind speed data is limited to the specific elevation, such as 2~3m, 10 m, and so on. In this study, the parameters of the vertical profile functions are estimated with optimal and analyzed the parameter ranges using the HeMOSU-1 platform wind data monitored at the eight different locations. The results show that the mean value of the exponent of the power function is 0.1, which is significantly lower than the typically recommended value, 0.14. The values of the exponent, the friction velocity, and the roughness parameters are in the ranges 0.0~0.3, 0~10 (m/s), and 0.0~1.0 (m), respectively. The parameter ranges differ from the typical ranges because the atmospheric stability condition is assumed as the neutral condition. To improve the estimation accuracy, the atmospheric condition should be considered, and a more general (non-linear) vertical profile functions should be introduced to fit the diverse profile patterns and parameters.

• ETRI Journal
• /
• v.9 no.2
• /
• pp.55-61
• /
• 1987

The effective cutoff wavelength of $LP_11$mode is measured as a function of fiber length for three types of single-mode optical fiber which have different characteristics in the index profile or the coating structure. The measured cutoff wavelength decreased linearly in a logarithmic scale of fiber length as increasing fiber length, and eventually became constant after 3km for two fiber types. It is found that the length dependence of cutoff wavelength is due to a mode coupling between the $LP_01$ and $LP_11$ modes.

• Journal of Korean Society for Geospatial Information Science
• /
• v.20 no.2
• /
• pp.15-22
• /
• 2012

The variation in the wind speed with height above ground is called the wind shear profile. In the field of wind resource assessment, analysts typically use one of two mathematical relations to characterize the measured wind shear profile: the logarithmic profile (log law) and the power law profile (power law). The logarithmic law uses the surface roughness as a parameter, and the power law uses the power law exponent as a parameter. The shape of the wind shear profile typically depends on several factors, most notably the roughness of the surrounding terrain and the stability of the atmosphere. Since the atmospheric stability changes with season, time of day, and meteorological conditions, the surface roughness and the power law exponent also tends to change in time. For this study, Using the observed data from Met-mast, located in Pyeongdae, Handong in Jeju. we used the matlab and windograper to calculate roughness length and the law exponents. These calculations are similar to reference the data, but they have different ranges. In the ocean case, each reference data and calculated data was the same, but the crop area is higher than the earlier studies. In addition, the agricultural village is lower than the earlier studies.

• 한국해양학회지
• /
• v.26 no.4
• /
• pp.340-349
• /
• 1991

From tidal current measurements on a tidal sand ridge in the Gyeonggi Bay from August 24 to September 29, 1987, tidal current velocities at 1.0 m above bottom (U/SUB 100/) and boundary shear velocities (U/SUB */) are calculated. The mean speeds of tidal current for flood and ebb over the entire period are 56.3 cm/sec and 63.7 cm/sec in mid-depth (9.0 m above bottom), and 43.9 cm/sec and 43.8 cm/sec in near-bottom (1.5 m above bottom). The exponent(P) in "power law", which is generally used for extrapolation from the mid-depth current velocity to that at the top of nationally logarithmic layer, is estimated to be 0.15 in the study area. Using logarithmic velocity profile assumption, mean values of U/SUB 100/ and U/SUB */ are calculated to be 41.4 cm/sec and 2.39 cm/sec, respectively. The mean value of U/SUB */ (2.39 cm/sec) is much higher than the critical shear velicity (U/SUB *c/) of 1.40 cm/sec reported by Choi (1990). and thus, it can be suggested that the most of sands on the tidal sand ridge in the study area are easily eroded and transported for the greater part of tidal period.