• Journal of the Korean Geotechnical Society
• /
• 제23권7호
• /
• pp.77-86
• /
• 2007

Installation damage of 3 types of geogrids was evaluated with compaction condition by laboratory tester. This experimental was in accordance with ENV ISO 10722-1. First, soil distribution and water content were conducted. And then we changed cyclic loading time and type of geogrids as a factor of installation damage. The samples are woven, warp-knitted, welded type of 6, 8, 10T. This study aims to give an insight into the relationships between installation damage and cyclic loading time. The result of studies was that strength of the damaged geogrids can be closely correlated with the time of loading cycles. Especially, welded type shows slower slope than two types of geogrids due to coating materials. That means welded type is coated with PP (Polypropylene), but the other two types of geogrids are coated with PVC (Polyvinyl Chloride). To confirm another factor different method was performed. The size of soil was used between 9.5 mm and 23.5 m to compare initial experimental. Cyclic loading compaction is taken 200 times before installation test and the reason is that the reduction factor of this case by installation damage was higher than other compaction loading conditions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• 제14권5호
• /
• pp.1211-1221
• /
• 1990

The purpose of this study is to get experimental data on the distribution of CWM (Coal- Water Mixture) droplets size and the presence of pulverized coal particles inside CWM droplets. Atomization of CWM is done by Twin-Fluid Atomizer. The operational parameters are atomizing air pressure, coal particle loading, mean size of pulverized coal particles and sampling positions across spray. Th data analysis is initiated by Impression Sampling Method(Magnesium Oxide Technique) and Photo-technique and counting works are followed. Experimental work induces following research results. The variation of particle loadings in slurry makes no appreciable effects on the mean size of CWM droplets. It is evident that atomizing air pressure has very strong effect on the atomization of slurry. The mean size of atomized fuel droplets is dramatically reduced with the increasing air pressure. The population ratio of droplets without coal particles to total number of droplets is decreased as atomizing air pressure or loading rises and the same trend is obtained as the mean size of coal particles becomes smaller but a certain tendency of coal particle presence inside droplets could not be found from the change of sampling positions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• 제14권5호
• /
• pp.1069-1078
• /
• 1990

It is shown that the performance of finite element based on energy orthogonal functions may be superior to conventional formulation for plane stress problem. Using this finite element, it is then attempted to show the distribution of stress concentration effect for subsurface under loading point. It turned out that the stress concentration effect for subsurface is not dependent on the width of the member but the loading area. And then it is shown that the solution attained by taking the stress function as a Fourier series is not satisfactory in y<0.1B.

• Archives of Pharmacal Research
• /
• 제19권1호
• /
• pp.30-35
• /
• 1996

Poly(l-lactic acid)(PLLA) microspheres loaded with ampicillin sodium (AMP-Na_, .betha.-lactam antibiotic, were prepared by a w/o/w multiple emulsion-solvent evaporation method. The amounts of each component in three phases (inner water phase, organic phase, and outer water phase) wre carefully examined in the preparation of PLLA microspheres. The stirring rate, another preparation parameter, was also investigated for study on the effect of mechanical stress on the drug loading and morphology of PLLA microspheres. Most of the preparation parameters had a great influence on the drug loading, surface morphology and size distribution of PLLA microspheres. PLLA microspheres with 15.89 w/w% drug loading were subjected to the in vitro release experimet. The release of ampicillin sodium was constant at a rate of 1.68 $mug/ml/day$ per 1 mg of microspheres for 18 days initial burst effect.

• Earthquakes and Structures
• /
• 제23권1호
• /
• pp.13-21
• /
• 2022

Masonry constructions exhibit uncertain behaviors under dynamic effects such as seismic action. Complex issues arise in the idealization of structural systems of buildings having different material types and mechanical properties. In this study, the structural behavior of a vaulted masonry building constructed using full clay brick and lime-based mortar and sitting on consecutive arches was investigated by experimental and numerical approaches. The dimensions of the structure built in the laboratory were 391 × 196 cm, and its height was 234 cm. An incremental repetitive loading was applied to the prototype construction model. Along the gradually increasing loading pattern, the load-displacement curves of the masonry structure were obtained with the assistance of eight linear displacement transducers. In addition, crack formation areas, and relevant causes of its formation were determined. The experimental model was idealized using the finite element method, and numerical analyses were performed for the area considered as linear being under similar loading effect. From the linear analyses, the displacement values and stress distribution of the numerical model were obtained. In addition, the effects of tie members, frequently being used in the supports of curved load-bearing elements, on the structural behavior were examined. Consequently, the experimental and numerical analysis results were comparatively evaluated.

• Coupled systems mechanics
• /
• 제12권2호
• /
• pp.167-181
• /
• 2023

The determination of the blast protection level and the corresponding minimum load-bearing capacity for a laminated glass (LG) window is of crucial importance for safety and security design purposes. In this paper, the focus is given to the window response under near-field blast loading, i.e., where relatively small explosives would be activated close to the target, representative of attack scenarios using small commercial drones. In general, the assessment of the load-bearing capacity of a window is based on complex and expensive experiments, which can be conducted for a small number of configurations. On the other hand, nowadays, validated numerical simulations tools based on the Finite Element Method (FEM) are available to partially substitute the physical tests for the assessment of the performance of various LG systems, especially for the far-field blast loading. However, very little literature is available on the LG window performance under near-field blast loads, which differs from far-field situations in two points: i) the duration of the load is very short, since the blast wavelength tends to increase with the distance and ii) the load distribution is not uniform over the window surface, as opposed to the almost plane wave configuration for far-field configurations. Therefore, the current study focuses on the performance assessment and structural behaviour of LG windows under near-field blasts. Typical behavioural trends are investigated, by taking into account possible relevant damage mechanisms in the LG window components, while size effects for target LG windows are also addressed under a multitude of blast loading configurations.

• Structural Engineering and Mechanics
• /
• 제89권6호
• /
• pp.627-634
• /
• 2024

This research deals with the process of conducting a reinforced concrete slab loading test of a Residential Complex Project at the Shatt Al Arab District which is located in southern Iraq. The purpose of the test which represents a destructive test is to evaluate the structural behavior of the slab condition state during and after the examination of the test process in order to ascertain the ability of the slab ceiling to withstand the loads generated during the use of the building. The test was carried out accordant to ACI 437.2-13 code. The reason for this test is the postponed 8 years of building project construction. Concrete blocks were used to simulate and conduct a loading test of 30-tons for 3 days. The central point has been installed to measure the slab deflection that occurred during the test. The results showed that both the total deflection and residual deflections were lesser than the permissible values according to the ACI 437.2-13, the RC slab behavior was mainly linear structural behave, and that the purpose of the examination was achieved. Finally, a new method was introduced to the assessment of the slab condition at the support which is found in good condition.

• Journal of the Korean Society for Railway
• /
• 제8권4호
• /
• pp.348-353
• /
• 2005

In designing the structures of railway rolling stocks, deterministic methods associated with the concept of a safety factor have been traditionally used. The deterministic approaches based on the mean values of applied loads and material properties have been used as safety verification for the design of rolling-stock car body structures. The uncertainties in the applied loading for the high speed train and the strength of new materials in the rolling stocks require the application of probabilistic approaches to ensure fatigue safety in the desired system. Pressure loadings acting on the car body when the train passes through tunnels show reflected pressure waves for high-speed trains and they may cause a fatigue failure in vehicle bodies. Use of new material technology as body structures also introduces uncertainties in the material strength. A probabilistic approach is more adaptable in designing reliable structures when the pressure waves from the tunnels pounds and new material technology is adopted. In this paper, it is proposed that a fatigue design and assessment method based on a reliability which deals with the loading variations on a railway vehicle due to the pressure reflected in tunnels and the strength variations of material. Equation for the fatigue reliability index has been formulated to calculate the reliability assessment of a vehicle body under fluctuating pressure loadings in a tunnel. Considered in this formulation are the pressure distribution characteristics, the fatigue strength distribution characteristics, and the concept of stress-transfer functions due to the pressure loading.

• Wind and Structures
• /
• 제25권5호
• /
• pp.493-506
• /
• 2017

Wind-induced response behavior of long-span roof structures is very complicated, showing significant contributions of multiple vibration modes. The largest load effects in a huge number of members should be considered for the sake of the equivalent static wind loads (ESWLs). Studies on essential matters and necessary conditions of the universal ESWLs are discussed. An efficient method for universal ESWLs on long-span roof structures is proposed. The generalized resuming forces including both the external wind loads and inertial forces are defined. Then, the universal ESWLs are given by a combination of eigenmodes calculated by proper orthogonal decomposition (POD) analysis. Firstly, the least squares method is applied to a matrix of eigenmodes by using the influence function. Then, the universal ESWLs distribution is obtained which reproduces the largest load effects simultaneously. Secondly, by choosing the eigenmodes of generalized resuming forces as the basic loading distribution vectors, this method becomes efficient. Meanwhile, by using the constraint equations, the universal ESWLs becomes reasonable. Finally, reproduced largest load effects by load-response-correlation (LRC) ESWLs and universal ESWLs are compared with the actual largest load effects obtained by the time domain response analysis for a long-span roof structure. The results demonstrate the feasibility and usefulness of the proposed universal ESWLs method.

• Coupled systems mechanics
• /
• 제4권4호
• /
• pp.365-383
• /
• 2015

Strip footing is an important type of shallow foundations and is commonly used beneath the walls. Analysis of shallow foundation involves the determination of stresses and deformations. Element free Galerkin method, one of the important mesh free methods, is used for the determination of stresses and deformations. Element free Galerkin method is an efficient and accurate method as compared to finite element method. The Element Free Galerkin method uses only a set of nodes and a description of model boundary is required to generate the discrete equation. Strip footing of width 2 m subjected to a loading intensity of 200 kPa is studied. The results obtained are agreeing with the values obtained using analytical solutions available in the literature. Parametric study is done and the effect of modulus of deformation, Poisson's ratio and scaling parameter on deformation and stresses are determined.