• Title/Summary/Keyword: Load-velocity Characteristics

Search Result 317, Processing Time 0.024 seconds

Kinematic Analysis of Several Linkage Drives for Mechanical Presses (다양한 링크구동 기계프레스에 대한 기구학적 분석)

  • 구형욱;황병복;임중연;이호용
    • Transactions of Materials Processing
    • /
    • v.6 no.6
    • /
    • pp.471-481
    • /
    • 1997
  • This paper is concerned with the kinematic analysis of several linkage drives for mechanical presses. Load and velocity characteristics of conventional presses are illustrated and a design of new drive for a mechanical press is represented. In this regard, a crank-slider mechanism with arc crank-pin guide is introduced and compared with other linkage drives. Kinematic performances are analyzed in respect of load capacity, slide velocity characteristics using a developed SS-Plot program. The new linkage drive turns out to be effective in terms of load and velocity characteristics, and productivity.

  • PDF

MEASUREMENT OF TURBULENCE CHARACTERISTICS BY USING PARTICLE TRACKING VELOCIMETRY

  • Yoon, Byung-man;Yu, Kwon-kyu;Marian Muste
    • Water Engineering Research
    • /
    • v.3 no.2
    • /
    • pp.135-142
    • /
    • 2002
  • This study investigates the effects of sediment on the flow characteristics such as velocity distribution, friction velocity, turbulent intensities, Reynolds stress, etc. Particle tracking velocimetry (PTY) is used to measure the vertical flow field. Results show that flow over the high bed-load concentration region has larger values of mean velocity and friction velocity and smaller values of turbulence intensities, compared to those for flow over the low bed-load concentration region.

  • PDF

Constant Velocity Revolution of an Unknown Load Using a Balance Beam Controller (밸런스빔을 이용한 미지부하 정속도 회전)

  • Kim, Yong-Jun;Yi, Keon-Young
    • Proceedings of the KIEE Conference
    • /
    • 2003.07d
    • /
    • pp.2227-2229
    • /
    • 2003
  • Using the gyro effect, Balance Beam Controller is developed with Samsung Corporation. Balance Beam Controller is possible to control the position of an object in air by controlling the attitude of inner gimbal. But in the unknown load inertia case, even a skilled worker it is not easy to operate a Balance Beam. That is caused by the difficulty to estimate the load inertia. If the amount of the gimbal operation is set excessively with a wrong load estimation, it can often cause accidents. To solve this problem, the control function which is revolving with velocity of the revolution has to be added to developed equipment. In this research, we analyze the characteristics of a Balance Beam(the smaller load inertia, the bigger force of restitution) using the angular velocity sensor, and present constant velocity revolving controller with estimating value of the load using this moving characteristics.

  • PDF

Effect of Refining Load on the Drainage Characteristics of Pulp (고해부하가 지층 형성시 탈수특성에 미치는 영향)

  • 김용식;원종명
    • Journal of Korea Technical Association of The Pulp and Paper Industry
    • /
    • v.32 no.4
    • /
    • pp.10-17
    • /
    • 2000
  • The change of fiber length, freeness, initial forming drainage velocity, specific filtration resistance, final drainage time and wet web dryness were measured to investigate the effect of the refining load on the drainage characteristics of pulp. The arithmetic average fiber length after refining with higher refining load was shorter than that obtained with lower refining load. Higher refining load decreased initial forming drainage velocity, final drainage time and wet web dryness. The refining load also affected the relationship between freeness and specific filtration resistance, initial forming drainage velocity, final drainage time. It was found that the specific filtration resistance is better than freeness to predict the drainage characteristics of pulp and the wet dryness.

  • PDF

Dynamic characteristics of flexibly supported infinite beam subjected to an axial force and a moving load (이동하중과 축하중이 작용하는 유연한 기초위에 지지된 무한보의 동특성)

  • 홍동균;김광식
    • Journal of the korean Society of Automotive Engineers
    • /
    • v.4 no.3
    • /
    • pp.56-68
    • /
    • 1982
  • This paper presents analytic solutions of defection and their resonance diagrams for a uniform beam of infinite length subjected to an constant axial force and moving transverse load simultaneously. Steady solutions are obtained by a time-independent coordinate moving with the load. The supporting foundation includes damping effects. The influences of the axial force, the damping coefficient and the load velocity on the beam response are studied. The limiting cases of no damping and critical damping are also investigate. The profiles of the deflection of the beam are shown graphically for several values of the load speed, the axial force and damping parameters. Form the results, following conclusions have been reached. 1. The critical velocity .THETA.cr decreases as the axial compressive force increases, but increases as the axial tensile force increase. 2. At the critical velocity .THETA.cr the deflection have a tendency to decrease as the axial tensile force increases and to increase gradually as the axial compressive force increases. 3. In case if relatively small dampings, the deflection increases suddenly as the velocity of the moving load approaches the critical velocity, and it reachs its maximum at the critical velocity, and it decreases and become greatly affected by the axial force as the velocity increases further. 4. in case of relatively large dampings, as the velocity increases the deflection decreases gradually and it is affected little by the axial load.

  • PDF

The vibration detection and analysis of 3-phase cast resin transformer in less than 50% load conditions (50% 미만 부하조건에서의 3상 몰드변압기 진동 측정과 분석)

  • Shong, Kil-Mok;Bang, Sun-Bae;Kim, Chong-Min;Kim, Young-Seok;Choi, Myung-Il
    • The Transactions of The Korean Institute of Electrical Engineers
    • /
    • v.61 no.7
    • /
    • pp.992-997
    • /
    • 2012
  • In this paper, we were analyzed the vibration characteristics of the three-phase cast resin transformer using less than 50% of load in the field. Most of the cast resin transformer is less than 50% in the domestic field is used for load conditions. Consisting of a solid insulator cast resin transformer is generating lots of noise and vibration. In addition, because it is affected by Joule 's heat is used in light load conditions. As a results, the transformer vibrations at frequencies below about from 200Hz to 500Hz were detected. Vibration velocity depends on the load variations were found. Load up to approximately 20-30% in most cases the vibration velocity was found at 4,000 ${\mu}m/s$ or less, 8,000 ${\mu}m/s$ or more. Vibration frequency at light load conditions were generated at the 120Hz, 240Hz, 360Hz and 480Hz. At the load condition of from 10% to 20%, vibration velocity is higher than another. Most of the vibration velocity were identified at the 1,000 ${\mu}m/s$ or less. Using the vibration frequency and velocity measurements data, the load on the cast resin transformer analyzed the correlation of the burden. Therefore, this data could be found in the vibration characteristics of the light-load conditions. If the field measurements using the data perform diagnostics on the transformer, it's expected to be very effective.

Optimization of the Dirve for Lineaer-Guide Press (직선가이드프레스 구동부의 최적화)

  • 이영섭;황병복
    • Transactions of Materials Processing
    • /
    • v.9 no.2
    • /
    • pp.171-178
    • /
    • 2000
  • This paper is concerned with the optimization of the drive for linear-guide press which is one of mechanical presses. The design of linear-guide drive for a mechanical press is introduced and the drive for the linear-guide press is optimized for the improvement of load and velocity characteristics. As a result of optimization, the load capacity during stroke increases and the slide velocity decreases in working region, respectively. The new design could be suited to many applications in precision forming such as extrusion and the sheet metal-forming processes.

  • PDF

A study on wind load characteristics of wind turbines (풍력발전기의 풍하중특성에 관한 연구)

  • Kim, Jung-Su;Park, Noh-Gill;Kim, Young-Duk;Kim, Su-Hyub
    • Proceedings of the Korean Society for Noise and Vibration Engineering Conference
    • /
    • 2010.10a
    • /
    • pp.124-129
    • /
    • 2010
  • Wind load characteristics is investigated for vibration analysis of wind turbine gearbox. A normal wind model assumed, of which the wind velocity is increased according to the height from ground. A blast wind model is assumed, of which the maximum velocity is located at the center and the velocity profile is normally distributed. The periodical torque and bending moments transmitted to the main shaft of wind turbine are investigated. The average values and the harmonic terms of the transmitted moments are studied on the wind direction of range $-45^{\circ}{\sim}45^{\circ}$ and the bending moment characteristics are examined, which is regarded as the main source of the misalignment of gear train.

  • PDF

Mechanical Pressure Drive with Enhanced Downward Velocity Characteristics (슬라이드의 하강속도특성을 개선한 기계프레스의 구동부)

  • 구형욱;최호준;황병복
    • Proceedings of the Korean Society for Technology of Plasticity Conference
    • /
    • 1996.03b
    • /
    • pp.110-120
    • /
    • 1996
  • A crank-slider mechanism is driven by the rotating disk with are crank-pin guide to be applied to the deep drawing and cold forging presses. Load characteristics for different presses are summarized to see the basics of deep drawing of sheet metal and forging in terms of load-stroke relationship. Several types of conventional deep drawing presses are also shown to be compared with the ratating disk-types press. Kinematic performances by thearc guide driving mechanism are anlayzed in terms of load capaicty, stroke, and slide velocity characteristics, and they are compared with those by conventional driving , e.g. Niagara-typepress and so on. Kinematically better performances is shown by arc guide drive than those by conventional ones. The new driving mechanism is also proven to be one of the best for mass production press in terms of short cycle time. Possible applications of the arc guide press to deep drawing and cold forging work are in terms of kinematics and load capacity.

  • PDF

Random vibration of multispan Timoshenko frames due to a moving load

  • Wang, Rong-Tyai;Lin, Jin-Sheng
    • Structural Engineering and Mechanics
    • /
    • v.6 no.6
    • /
    • pp.673-691
    • /
    • 1998
  • In this paper, an analytic method to examine the random vibration of multispan Timoshenko frames due to a concentrated load traversing at a constant velocity is presented. A load's magnitude is a stationary process in time with a constant mean value and a variance. Two types of variances of this load are considered: white noise process and cosine process. The effects of both velocity and statistical characteristics of load and span number of the frame on both the mean value and variance of deflection and moment of the structure are investigated. Results obtained from a multispan Timoshenko frame are compared with those of a multispan Bernoulli-Euler frame.