• 한국구조물진단유지관리공학회 논문집
• /
• 제8권4호
• /
• pp.239-246
• /
• 2004

충격하중에 대한 양단 고정보의 거동을 강 소성 모델을 이용하여 파악 하였다. 또한 손상을 발생시키는 정 역학적 붕괴하중과 이상임펄스에 대한 하중최대치 비와 임펄스 비를 이용하여 손상곡선을 작성하였다. 작성된 손상곡선으로부터 충격하중의 하중 최대치와 임펄스는 구조물의 안전에 중요 변수가 됨을 보였으며 또한 하중최대치 비와 임펄스 비로 작성된 손상곡선은 하중작용시간과 하중의 형태 그리고 구조물의 동적 특성이 함께 고려된 기준으로, 등가 동하중에 초점을 맞추어 일괄적으로 구조물의 안전성을 판단할 수 있는 방법이다.

• Smart Structures and Systems
• /
• 제17권6호
• /
• pp.1107-1127
• /
• 2016

Studies on dynamic characteristics of the hanger vibration using field monitoring data are important for the design and evaluation of high-speed railway truss arch bridges. This paper presents an analysis of the hanger's dynamic displacement responses based on field monitoring of Dashengguan Yangtze River Bridge, which is a high-speed railway truss arch bridge with the longest span throughout the world. The three vibration parameters, i.e., dynamic displacement amplitude, dynamic load factor and vibration amplitude, are selected to investigate the hanger's vibration characteristics in each railway load case including the probability statistical characteristics and coupled vibration characteristics. The influences of carriageway and carriage number on the hanger's vibration characteristics are further investigated. The results indicate that: (1) All the eight railway load cases can be successfully identified according to the relationship of responses from strain sensors and accelerometers in the structural health monitoring system. (2) The hanger's three vibration parameters in each load case in the longitudinal and transverse directions have obvious probabilistic characteristics. However, they fall into different distribution functions. (3) There is good correlation between the hanger's longitudinal/transverse dynamic displacement and the main girder's transverse dynamic displacement in each load case, and their relationships are shown in the hysteresis curves. (4) Influences of the carriageway and carriage number on the hanger's three parameters are different in both longitudinal and transverse directions; while the influence on any of the three parameters presents an obvious statistical trend. The present paper lays a good foundation for the further analysis of train-induced hanger vibration and control.

• 대한기계학회논문집
• /
• 제19권4호
• /
• pp.1051-1061
• /
• 1995

In order perform leak-before-break design of nuclear piping systems and integrity evaluation of reactor vessels, full stress-strain (.sigma. - .epsilon.) curves and fracture resistance (J-R) curves are required. However it is time-consuming and expensive to obtain J-R curves experimentally. The objective of this paper is to develop two methods for J-R curve prediction. In the first method, elastic-plastic finite element analyses for a series of crack length / specimen width ratio were performed. Accordingly the load versus load line displacement (P .delta.) curve corresponding to the fracture strain is obtained and the J-R curve based on the generalized locus method is obtained. In the second method, the correlation between .sigma.-.epsilon. curves and J-R curves was statistically analyzed and an empirical equation to predict the J-R curve from the .sigma.-.epsilon. test result is proposed. A good correlation between the predicted results based on the proposed methods and the experimental ones is obtained.

• Steel and Composite Structures
• /
• 제39권2호
• /
• pp.135-148
• /
• 2021

Hollow structural section (HSS) columns have been increasingly popular due to their structural and architectural merits. However, practical difficulty lies in developing proper connections. The through-diaphragm connections are considered as suitable connection type that is widely adopted in Asian countries. However, the stress concentration occurs at the location connecting through-diaphragm and steel beam. Furthermore, the actual load path from the beam flange is not uniformly transferred to the HSS column as conventionally assumed. In this paper, tensile tests were further conducted on three additional specimens with beam flange plate to evaluate the load versus displacement response. The load-displacement curves, yield and ultimate capacity, ductility ratio were obtained. Furthermore, the strain development at different loading levels was discussed comprehensively. It is shown that the studied connection configuration significantly reduces the stress concentration. Meanwhile, simplified trilinear load-displacement analytical model for specimen under tensile load was presented. Good agreement was found between the theoretical and experimental results.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.57-64
• /
• 2005

Since the allowable bearing capacities of piles in weathered/fractured rock are mainly governed by settlement, the load-displacement behavior of the rock socketed pile should be well known. To predict pile head settlement at the design stage, the exact understanding of the load-transfer mechanisms is essential. Therefore, in this research, the load-transfer mechanisms of drilled shaft socketed into weathered rock was investigated. For that, 5 cast-in-place concrete piles with diameters of 1,000 mm were socketed into weathered gneiss. The static axial load tests and the load-transfer measurements were performed to examine the axial resistant behavior of the piles. A comprehensive field/laboratory testing program on weathered rock at the field test sites was also performed to describe the in situ rock mass conditions quantitatively. And then, the effect of rock mass condition on the load transfer mechanism was investigated. The side shear resistance of the pile in moderately weathered rock reached to yielding point at a few millimeter displacements, and after that, the rate of resistance increment dramatically decreased. However, that in the highly /completely weathered rock did not show the obvious yielding point, and gradually increased showing the hyperbolic pattern until with the relatively high displacement (>10 mm). The end bearing-displacement curves showed linear increase at least until with the base displacement of approximately 10 mm, regardless rock mass conditions.

• 한국지반환경공학회 논문집
• /
• 제13권8호
• /
• pp.57-64
• /
• 2012

본 연구에서는 모형실험을 실시하여 수평하중 작용 시 무리말뚝의 거동을 평가하였다. 암반을 모사한 콘크리트 블럭에 모형말뚝을 말뚝직경(D)의 1배로 근입시키고, 상부에 모래를 1m 깊이로 포설한 $2{\times}3$ 배열의 무리말뚝에 대하여 모형실험을 실시하였다. 그리고 말뚝길이는 11D, 15D와 20D의 세 종류이다. 각 조건에 대한 모형실험의 결과를 수평하중-변위 곡선으로 나타냈으며, 지반 속에서 발생한 말뚝의 변위를 측정하였다. 모형실험 결과, 말뚝 길이/직경의 비(L/D)가 작아질수록 항복하중은 커지고, 항복하중에서의 수평변위는 증가하는 경향을 나타냈다. 도로교설계기준의 수평변위 기준인 15mm에서의 하중을 비교한 결과, L/D가 11, 15, 20에서의 항복하중은 각각 11.7, 6.2, 3.4kN으로 나타났다. 모든 실험 조건에 대하여 지반 속에서 발생한 말뚝의 수평변위는 거의 직선적으로 나타났고, 모형 말뚝이 콘크리트 블록에 소켓된 지점에서 파괴가 발생하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 추계 학술발표회
• /
• pp.357-367
• /
• 2010

In this study, several design and construction cases of the pile bent system for bridges were introduced. The lateral displacement of the pile bent system is larger than the displacement of pile cap system, due to the smaller bending stiffness and the longer unsupported length. So, the analysis of the lateral pile displacement is main factor for the design of pile bent system and superstructure. For the accurate estimation of the pile displacement, an iterative analysis method was developed. The superstructure was analyzed regarding the pile foundation as $6{\times}6$ spring and the substructure was analysed using non-linear load transfer curves (p-y, t-z, q-z curve). And, to verify this analysis method, the estimated displacements are compared with the results of lateral load test. This analysis method is expected to be a viable alternative approach for the design of bridge foundation hereafter.

• 한국공작기계학회논문집
• /
• 제13권6호
• /
• pp.23-28
• /
• 2004

Impact behavior of polycarbonate in various defect state was investigated using an instrumented impact tester. A method of analyzing raw impact data was developed and successfully demonshsted the impact behavior in terms of load-displacement and energy-displacement curves. This technique was shown to be capable of separating defect no-defect initiated fractures as well as their propagation behaviors.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.262-267
• /
• 2002

Impact behavior of polycarbonate in various defect state was investigated using an instrumented impact fester. A mettled of analyzing raw impact data was developed and successfully demonstrated the impact behavior in terms of load-displacement and energy-displacement curves. This technique was shown to be capable of separating defect, no-defect initiated fractures as well as their propagation behaviors.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.238-244
• /
• 2006

The Light Collision Safety Device is used to protect the important part of trains and passengers at the low velocity accidents. The Light Collision Safety Device comprises mainly tension bolts, shear bolts and an energy absorber. The work mechanism of this device is that first, the tension bolts break at designed collapse load and second, the energy absorber absorb rest collision energy. In this paper, the tension bolt characteristics were validated by the simple tension test using the FEM(Finite Element Method) and the characteristic of the two types of energy absorber were compared by using the load-displacement curves and absorbed energy. Last, in order to determine integrated load-displacement curve of tension bolts and the energy absorber, the unified analysis was conducted by using the FEM.