• 한국자동차공학회논문집
• /
• 제13권2호
• /
• pp.127-134
• /
• 2005

This paper introduces a newly developed high speed material testing apparatus for tensile tests at the strain rate up to 500/sec. The tensile properties of sheet metals are indispensable for the accurate crashworthiness analysis of auto-bodies since the local strain rate reaches to 500/sec in the car crash. An appropriate experimental method has to be developed to acquire the tensile properties at the intermediate strain rate ranged from 0.003/sec to 200/sec. Tensile tests of various different steel sheets for an auto-body were perform ed to obtain the dynamic properties with respect to the strain rate. The dimensions of specimens that can provide the reasonable results were determined by the finite element analysis. A special jig fixture of a load cell is designed to reduce the load ringing phenomenon induced by unstable stress propagation at the high strain rate. Stress-strain curves were acquired for each steel sheet from the dynamic tensile test and utilized to obtain the relationship of the stress to the strain rate.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 춘계학술대회 논문집
• /
• pp.214-214
• /
• 2003

During a model test of Hutton TLP, a "ringing" response was first observed about 20 years ago. This phenomenon is a resonant build up over the time of wave period and this burst-like motion can cause the extreme load on the TLP tether. It is often detected in the large and steep irregular waves but the generation mechanism leading to the "ringing" is not yet well understood. According to the research since then, the higher order harmonic components may account for the "ringing" on the floating offshore structures. The main purpose of the present research is, thus, to measure the higher harmonic forces exerted on a vertical truncated circular column and to compare them with available data. A vertical truncated cylinder with a diameter of 3.5inch and a draft of 10.5inch is used as a test structure, which is a scaled model of ISSC TLP column. The cylinder is installed at a distance of 45ft from the wave maker in order to avoid parasitic waves created in the wave flap. Attached to the upper part of the cylinder are two force gages to measure the horizontal (surge) and vertical (heave) forces on the cylinder. The incoming waves are Stokes waves with a slope ranging from 0.06 to 0.24. The forces and waves are measured for 60 seconds with a sampling rate of 50 Hz. Among the recorded data, the first 10 waves are excluded because of transient behavior of the waves and the next The horizontal and vertical forces are analyzed up to 5th order harmonics. The horizontal forces are then compared to the values from the theoretical model called "FNV model". In addition, force transfer functions are also investigated. Major findings in this research are below. 1) The first order forces measured are slightly larger than the theoretical values of "FNV model" 2) The "FNV model" considerably overpredicts the second order forces. 3) The larger the amplitude and more extreme the wave slope, the smaller the predictions are compared to the experimental. 4) The higher harmonic forces are significantly smaller than the first harmonic force for all wave parameters. 5) The normalized forces vs. waves slopes are almost constant in the lower harmonics but vary a lot in the higher harmonics. 6) The trend of forces is more nonlinear in the horizontal forces than in the vertical forces as the wave slope increases. 7) The part of the results above is also observed by other researchers and confirmed again through the present work.

• 대한전자공학회논문지SD
• /
• 제49권1호
• /
• pp.15-24
• /
• 2012

본 논문에서는 Switched-Capacitor 지연 기법의 새로운 고해상도 DPWM 발생기를 사용한 Dynamic-Response-Free SMPS를 제안한다. 제안된 회로는 Switched-Capacitor 지연 기법을 이용한 DPWM 발생기의 내부 커패시터 전압 기울기를 제어하는 방식으로 DPWM의 duty ratio를 결정한다. 제안된 회로는 컨버터의 피드백 전압과 기준전압을 비교하여 DPWM 발생기의 내부 캐패시터에 충방전되는 전류량을 제어하는 방식으로 출력전압 tracking이 가능하다. 따라서 제안된 회로는 기존 closed loop 제어 방식의 SMPS들에서 문제점이 되고 있는 동적 응답특성을 고려할 필요가 없으며, 출력 전압에 overshoot/undershoot로 인한 ringing 현상이 발생하지 않는다는 큰 장점을 가진다. 제안된 회로는 1MHz~10MHz까지 스위칭주파수를 사용자가 선택할 수 있으며, 100MHz의 내부 제어 동작 주파수로 10MHz 최대 스위칭 주파수(DPWM) 발생이 가능하다. 100MHz의 내부 제어 동작 주파수를 사용하여 10MHz 스위칭 주파수 발생시 소모되는 내부 회로의 최대 전류는 2.7mA이며, 출력 버퍼를 포함한 전체 시스템의 전류 소모는 15mA이다. 제안된 회로는 0.125%의 DPWM duty ratio 해상도를 가지고 부하에 최대 1A까지 전류공급이 가능하며, 최대 리플 전압은 8mV이다. 동부하이텍 BCD $0.35{\mu}m$ 공정 파라미터를 이용해 시뮬레이션을 수행하여 제안된 회로의 동작을 검증하였다.