• 한국지반공학회논문집
• /
• 제25권6호
• /
• pp.59-72
• /
• 2009

대구경 해상 말묵의 수평 하중전이 거동 및 변형 해석을 위해 p-y 하중전이 해석법이 널리 사용되고 있다. 그러나, 본 연구에서는, 기존의 p-y 해석법의 단점을 극복하여, 지반의 연속성을 고려한 수평방향 하중전이 해석을 고찰하였으며, 3D wedge failure mode의 이론적인 해법과 재하시험을 통해 말뚝의 실제 거동에 보다 부합되도록 연약지반의 p-y 곡선을 제안하였다. 제안된 하중전이함수법의 타당성을 검증하기 위하여 현장재하시험 사례와의 비교분석을 수행하였고, 그 결과 제안된 해석방법은 기존 p-y 곡선에 비해 대구경 해상말뚝의 거동 및 변형 특성을 적절히 예측함을 알 수 있었다.

• 한국재난정보학회 논문집
• /
• 제19권4호
• /
• pp.958-967
• /
• 2023

연구목적: 본 연구는 화재위험도가 높은 플랜트 시설물에 적용하고 있는 국내 내화성능을 분석하고 적합한 내화저항성능을 확보하여 플랜트 시설물의 화재 안전성을 확보하고자 한다. 연구방법:유한요소해석 프로그램인 Ansys를 활용하여 화재하중과 내화피복을 변수로 열전달 해석과 구조해석을 수행하고 해석 결과에 따른 플랜트 시설물의 내화성능을 분석하였다. 연구결과: 국내 플랜트 시설물에 적용된 내화피복은 UL 1709에 제시된 탄화수소화재의 화재하중을 적용하였을 때 내화성능을 확보하지 못하였으며 화재 후 강재의 변형 또한 크게 나타남을 확인하였다. 결론:현재 플랜트 시설물에 적용된 국내의 내화성능은 석유화학 플랜트 등과 같이 급격한 화재성장과 큰 화재하중에서 내화성능을 확보할 수 없으며 플랜트 시설물의 성능평가를 통해 적합한 내화성능을 평가하여 화재 안전성을 확보하여야 한다.

• Journal of Welding and Joining
• /
• 제33권2호
• /
• pp.69-77
• /
• 2015

High strength steels have been continually being developed to improve in fuel economy in automotive and ensure safety of passengers. New bonding and welding methods have been required for improving weldability on high strength steels. In this study, resistance spot welding and Weld-bond with nugget diameters of 4.0mm, 5.0mm, 6.0mm and 7.0mm were produced and tested, respectively. In order to confirm the effect of nugget diameters on tensile shear characteristic of the Weld-bond, tensile shear characteristics of Weld-bond were compared with those of resistance spot welding and adhesive bonding. Peak load of Weld-bond were increased as the nugget diameter increases. After appearing maximum peak load continuous fracture followed with second peak owing to load being carried by resistance spot weldment. Fracture modes of the adhesive layer in Weld-bond fractures were represented by mixed fracture mode, which are cohesive failure on adhesive part and button failure at resistance spot welds. The results showed that the tensile shear properties can be improved by applying Weld-bond on TRIP steel, and more apparent with nugget diameter higher than 5${\surd}$t.

• 대한기계학회논문집A
• /
• 제27권11호
• /
• pp.1986-1996
• /
• 2003

Methodology based on the elastic-plastic fracture mechanics has been widely accepted in predicting the critical crack length(CCL) of pressure tubes of CANDU nuclear plants. A conservative estimate of CCL is obtained by employing the J-resistance curves measured with the specimens satisfying plane strain condition as suggested in the ASTM standard. Due to limited thickness of the pressure tubes the curved compact tension(CT) specimens taken out from tile pressure tube have been used in obtaining J-resistance curves. The curved CT specimen inevitably introduce slant fatigue crack during precracking. Hence, effect of specimen geometry and slant crack on J-resistance curve should be explored. In this study, the difference of J integral values between the standard CT specimens satisfying plane strain condition and the nonstandard curved CT with limited thickness (4.2mm) is estimated using finite element analysis. The fracture resistance curves of Zr-2.5Nb obtained previously by other authors are critically discussed. Various finite element analysis were conducted such as 2D analysis under plane stress and plane strain conditions and 3D analysis for flat CT, curved CT with straight crack and curved CT with slant crack front. J-integral values were determined by local contour integration near the crack tip, which was considered as accurate J-values. J value was also determined from the load versus load line displacement curve and the J estimation equation in the ASTM standard. Discrepancies between the two values were shown and suggestion was made for obtaining accurate J values from the load line displacement curves obtained by the curved CT specimens.

• 한국강구조학회 논문집
• /
• 제19권4호
• /
• pp.425-434
• /
• 2007

SC 합성기둥은 기존의 합성기둥들이 가지는 내력상승, 방청효과, 공사기간 단축이 가능하고, 충전상태의 육안확인도 용이하여 이와 관련된 연구가 활발히 진행되고 있지만 SC합성기둥의 내화성능에 관한 연구는 미흡한 실정이다. 이에 본 논문에서는 SC합성기둥의 내화성능평가를 위해 하중비, 콘크리트 면적비, 피복유무를 변수로 두어 실험을 수행하였다. 또한 온도증가에 따른 실험체의 강도감소를 단순 수치해석으로 산출하여 내화성능시간을 유추하였고, 실험결과와 비교분석 하였다. 이 실험을 통하여 하중비가 작을수록 내화성능은 향상되었다. 그러나 콘크리트 면적비는 SC합성기둥의 내화성능 향상에 큰 영향을 미치지 못하였다.

• 대한토목학회논문집
• /
• 제26권5C호
• /
• pp.343-350
• /
• 2006

국내 기초구조물에 대한 저항계수 산정 및 하중저항계수설계법(LRFD) 개발의 일환으로 항타강관말뚝에 대한 저항편향계수를 산정하였다. 정재하시험 및 지반조사 자료를 수집하여 국내외의 기준에 따른 극한지지력을 산정한 후 말뚝의 대표 극한지지력을 결정하였다. 자료의 통계분석 결과에 기초하면, Davisson 기준이 말뚝의 극한지지력을 가장 합리적으로 평가하는 것으로 나타났다. 정역학적 지지력 공식과 N치를 이용한 Meyerhof 경험식을 이용하여 설계 극한지지력을 산정하였다. 이들 자료의 비교 분석을 통해 항타강관말뚝의 저항편향계수는 정역학적 지지력공식과 Meyerhof 경험식에 대해 각각 0.98, 1.46으로 산정되었다. 또한 두 가지 지지력 산정방법 중 정역학적 지지력공식의 불확실성이 상대적으로 낮은 것으로 나타났다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.318-318
• /
• 2009

The door stiffness is one of the important factors side impact. Generally, the researches have been conducted on the assembled door module. This study is to analysis the side impact characteristics for automotives door module. The impact characteristics have been determined by door module side impact test machine. To determine the initial, intermediate and peak crush resistances use the plot of load versus displacement and obtain the integral of the applied load with respect to the crush distances specified below for each door tested. The initial crush resistance is the average force required to deform the door through the initial 6 inches of crush. The intermediate crush resistance is the average force required to deform the door through the initial 12 inches of crush. The peak crush resistance will be directly obtained from the plot of load versus displacement since it is the largest force required to deform the door through the entire 18 inches crush distance. The data are used to determine if a specific vehicle or item of automotives equipment meets the minimum performance requirements of the subject Federal Motor Vehicle Safety Standard(FMVSS). FMVSS Static 214, Side impact protection, specifies performance requirements for protection of occupants in side impact crashes.

• Journal of Welding and Joining
• /
• 제21권2호
• /
• pp.42-49
• /
• 2003

The protection of steel surfaces against wear is a practical problem far agricultural, mining and manufacturing industries. Commercial processes are available in which a hard tungsten carbides rich steel layer is formed on the surface of carbon steel digging, drilling and gouging tools to improve their wear resistance. The nature of the interaction of the tungsten carbide with the steel matrix is important in determining the wear and corrosion properties of the resulting metal matrix composites(MMC). In the study, WC-12%Co/low carbon steel MMC overlays have been prepared by gas metal arc welding(GMAW) according to size of WC-12%Co grits. The characteristics wear resistance and wear mechanism have been investigated in relation to the experiment conditions each other. After MMC overlay had been tested by rubber wheel abrasion test, it was known that MMC overlay has a excellent wear resistance. Fe$_{6}$W$_{6}$C carbides of matrix in overlays were not important to restrain rubber wheal abrasion wear. Wear loss is proportioned to a applied load according to time. On the case of low load, wear occurred severely in the matrix of overlay more than WC-12%Co grit, on the contrary it is reverse on the case of high load because of fracture of WC-12%Co grits.its.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 춘계 학술발표회 초청강연 및 논문집
• /
• pp.1195-1205
• /
• 2008

Composite piles have been used in ground conditions where conventional piles are unsuitable or uneconomical. They may consist of a combination of timber and concrete pile in Europe. One method of doing this was to drive a steel tube to just below water level, and a concrete pile was lowered down it and driven to the required level where corrosion was susceptible in U.K. Recently, a fiber reinforced polymer (FRP) composite pile was developed to use in many marine locations for piers and waterfront buildings in the USA(Hoy, 1995; Phair, 1997). A steel composite (SC) pile reinforced concrete spun pile with steel tube was also proposed and used for the foundation acting a high lateral earthquake load. Composite piles have been developed and researched to increase lateral resistance or to prevent corrosion in marine structures. In paper, the composite pile consisting of the steel upper portion and the concrete lower portion is proposed and are carried out several tests to confirm the capacity of the pile such as lateral load test, dynamic load tests and bending test. It is noted that the composite pile would be a economical pile being capable of increasing lateral resistance.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.334-334
• /
• 2010

In order to fabricate the multilayer piezoelectric transformer by tape casting method, we investigated the effect of $TiO_2$ and PZT powder additions on the Ag/Pd electrode. Meanwhile, effects of $TiO_2$ and PZT powder additives on the microstructure and electrical properties of Ag/Pd electrode were investigated in detail. In addition, the multilayer piezoelectric transformers were fabricated and the characteristics with various load resistance were measured at resonance frequency. The voltage step-up ratio was continuously change with increasing input voltage and load resistance, and then output voltage and powers were increased with increasing input voltage at matching impedance. The temperature rise of multilayer piezoelectric transformers were increased with increasing input voltage and load resistance. Meanwhile, multilayer piezoelectric transformers sintered at $1100^{\circ}C$ show the favorable characteristics with a power of 15 W at $100\;{\Omega}$.