• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계학술발표회 논문집(I)
• /
• pp.438-441
• /
• 2006

Since the behavior of structural members subjected to blast load shows different responses, the effect of impulse as well as peak load should be considered in the damage analysis. The threshold on P-I diagram that causes specific damage level divides the diagram into the failure zone and the non-failure zones. In this study, numerical analysis is performed based on single-degree-of-freedom (SDOF) techniques to generate rational P-I diagram considering material non-linearity and dual failure modes (flexure and direct shear) of RC beams. From the comparison with existing test results it is concluded that proposed numerical method is good to derive failure mode of RC beam under blast load.

• Structural Engineering and Mechanics
• /
• 제42권3호
• /
• pp.363-381
• /
• 2012

This study is aimed at providing an efficient analytical model to obtain pressure- impulse diagram of one-way reinforced concrete slabs subjected to different shapes of air blast loading using single degree of freedom method (SDOF). A tri-linear elastic perfectly plastic SDOF model has been used to obtain the pressure-impulse diagram to correlate the blast pressure and the corresponding concrete flexural damage. In order to capture the response history for the slab, a new approximately SDOF method based on the conventional SDOF method is proposed and validated using published test data. The influences of pulse loading shape on the pressure-impulse diagram are studied. Based on the results, a pressure-impulse diagram generation method using SDOF and an analytical equation for the pressure-impulse diagram is proposed to different damage levels and different blast loading shapes.

• Tribology and Lubricants
• /
• 제13권3호
• /
• pp.28-32
• /
• 1997

Indentation, scratch and sliding tests were carried out in this paper to predict the critical loads and the failure modes of TiN-coated specimen. The test specimens were S20C steels with three different substrate hardness, roughness and coating thickness. The scratch test shows that the coating thickness has more dominant effect on the critical load of coated disk than the hardness and the roughness. Using the percent contact load, the ratio of sliding load to the critical scratch load, the cycles to failure are measured to predict the wear-life of TiN film. On the wear-life diagram the percent loads and the cycle to failure show the good linear relation on semi-log coordinate. With decreasing loads, the diagram shows the wear-limit at which the coated disk survives more than 4000 cycles.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 A
• /
• pp.419-421
• /
• 2002

This paper presents a methodology for the application of Unified Modeling Language (UML) to develop the new load management system. Development of new load management system in competitive electricity market is very complex since it requires too much data of power system. For the efficient and flexible design to develop of new load management system, a UML approach in applied which is composed of a class diagram, package diagram using Rational Rose Unified Process.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.179-180
• /
• 2002

In this study. the friction transition diagram based on the effect of oxide layer formation on contact surface between TiN coated steel ball and uncoated steel disk was constructed. From the diagram. it can be seen that as the contact load increases. the contact number of cycle at the beginning of oxide layer formation decreases linearly and as the coating thickness increases and the surface roughness of steel disk increases under same contact load. that increases. For the coated ball specimen, a AISI 52100 steel ball was used and AISI 1045 steel was used for the disk counter part.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.758-763
• /
• 2001

A concept called Allowable Load Set (ALS) is introduced and methods of finding its boundaries are developed. The resulting diagram allows an easy understanding of load and strength characteristics of a structure in relation to structural integrity under uncertain loading conditions. An allowable load diagram for an ALS visualizes the relation between a prescribed load and a degree of safety of the structure. During the application of the algorithms, critical areas of the structure are identified. A systematic method of finding the allowable load sets for multi-body mechanical systems is especially presented and applied to an excavator as a realistic case.

• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.328-334
• /
• 1999

Acoustic emission (AE) sensor was used to evaluate the wear-life of CrN-coated steel disks with 1 $\mu\textrm{m}$ and 4 $\mu\textrm{m}$ coating thickness. The relationship between Af and friction signal from scratch test and sliding test was investigated. The first spatting of CrN film was detected by AR signals in the early stage of coating failures, and overall failures by friction signals. Therefore, the conservative design for coating-life should be done using the results of AE signals. Using the percent contact load, the ratio of sliding normal load to the critical scratch load and the number of cycles to failure was measured to predict the wear-life of CrN film. On the wear-life dia-gram the percent contact loads and the number of cycles to failure showed a good linear relationship on the log coordinate. As the load percentage was decreased, the diagram showed that the wear-limits, at which the coated steels survived more than 35,000 cycles, were about 4∼5% of the critical scratch loads.

• 한국안전학회지
• /
• 제37권5호
• /
• pp.1-6
• /
• 2022

In this study, to confirm the effects of the mixed load of normal and shear forces acting on a fixing bolt, fatigue design criteria were developed by varying the loading angle and conducting tensile and fatigue tests. After evaluating and comparing the test results under different loading angles, the evaluation criteria were selected. These evaluation criteria were then applied to develop the design criteria. An Arcan fixture was designed and manufactured to simultaneously apply a mixed load of normal and shear forces to the fixing bolt of a turntable, and a fatigue test was conducted. S-N diagrams for various loading angles were obtained, and a 1% P-S-N diagram of failure probability was determined using statistical processing techniques. Our results show that failures of the fixing bolt can be prevented using these diagrams as a basis for developing fatigue design criteria.

• Structural Engineering and Mechanics
• /
• 제30권6호
• /
• pp.665-678
• /
• 2008

The beams components subjected to the loading such as axial, bending and cyclic thermal loads were studied in this research. The used constitutive equations are those of elasto-plasticity coupled to ductile and/or creep damage. The nonlinear kinematic hardening behavior was considered in elastoplasticity modeling. The unified damage law proposed for ductile failure and fatigue by the author of Sermage et al. (2000) and Kachanov's creep damage model applied to cyclic creep and low cycle fatigue of beams. Based on the results of the analysis, the shakedown limit loads were determined through the calculation of the residual strains developed in the beam analysis. The iterative technique determines the shakedown limit load in an iterative manner by performing a series of full coupled elastic-plastic and continuum damage cyclic loading modeling. The maximum load carrying capacity of the beam can withstand, were determined and imposed on the Bree's interaction diagram. Comparison between the shakedown diagrams generated by or without creep and/or ductile damage for the loading patterns was presented.

• 전기의세계
• /
• 제27권5호
• /
• pp.69-75
• /
• 1978

3 phase induction motor applied in the method of connecting it directly across the line needs large current when it starts. At that time, leakage magnetic pathes of interior of the motor are severely saturated and leakage reactances are decreased because of saturation. Consequently, increased current and raised powerfactor yield increase of starting torque. The author, noticing those phenomena, derived experimentally the raion of decreasing leakage reactance from the fact that when voltage applied to motor is increased under locked condition the magnitude of current and phase angle are varied, and determined tha equations of starting current and starting torque, considering the decrease of leakage reactance by the large starting current. The author calculated the characteristics of Current-Time and Speed-Time with the determined equation at specific load conditions, and compared the values obtained from above calculations with those from circle diagram's method and the practically recorded values at same load conditions. Therefore, the authos got a confidience that the results of the derived theory coincide with the practically measured values more well than circle diagram's results and circle diagram's equation should be modified in order to analize the starting status of a induction motor.