• Ocean Systems Engineering
• /
• v.4 no.4
• /
• pp.309-325
• /
• 2014

Geotextile tubes are basically a huge sack filled with sand or dredged soil. Geotextile tubes are made of permeable woven or non-woven synthetic fibers (i.e., polyester or PET and polypropylene or PP). The geotextile tubes' performances in strength, dewatering, retaining solid particles and stacked stability have been studied extensively in the past. However, only little research has been done in the observation of the deformation behavior of geotextile tubes. In this paper, a large-scale apparatus for geotextile tube experiment is introduced. The apparatus is equipped with a slurry mixing station, pumping and delivery station, an observation station and a data station. For this study the large-scale apparatus was utilized in the studies regarding the stresses on the geotextile and the deformation behavior of the geotextile tube. Model tests were conducted using a custom-made woven geotextile tubes. Load cells placed at the inner belly of the geotextile tube to monitor the total soil pressure. Strain gauges were also placed on the outer skin of the tube to measure the geotextile strain. The pressure and strain sensors are attached to a data logger that sends the collected data to a desktop computer. The experiment results showed that the maximum geotextile strain occurs at the sides of the tube and the soil pressure distribution varies at each geotextile tube section.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.76.2-76.2
• /
• 2010

The gas diffusion layer is the key component of the proton exchange membrane fuel cell because it directly affect to the mass transport mechanism and dynamic behavior of the cell. In this study, the effects of GDL aging on the transient response of the PEM fuel cell is systematically investigated using current step transient response analysis under different stoichiometric ratios and humidity conditions. With GDLs aged by the accelerated stress test, the effects of hydrophobicity and structural changes due to carbon loss in the GDL on the transient response of PEM fuel cells are determined. The degraded GDLs that had uneven hydrophobicity distributions cause local water flooding inside the GDL and induce lower and unstable voltage responses after load changes.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2660-2664
• /
• 2003

In this study, the concept of autonomous mobility is applied to a medical service robot. The aim of the development of the service robot is for the elderly assisting walking rehabilitation. This study aims that the service robot design parameter is proposed in ergonomic view. The walking assistant path pattern is derived from analyzing the elderly gait analysis. A lever is installed in the AMR in order to measure the pulling force and the leading force of the elderly. A lever mechanism is applied for walking assistant service of the AMR. This lever is designed for measuring the leading force of the elderly. The elderly adjusts the velocity of the robot by applying force to the lever. The action scope and the service mechanism of the robot are developed for considering and analyzing the elderly action patterns. The ergonomic design parameters, that is, dimensions, action scope and working space are determined based on the elderly moving scope. The gait information is acquired by measuring the guide lever force by load cells and working pattern by the electromyography signal.

• Carbon letters
• /
• v.22
• /
• pp.42-47
• /
• 2017

In this paper, the in vitro biocompatibility of graphene film (GF) with osteoblasts was evaluated through cell adhesion, viability, alkaline phosphatase activity, F-actin and vinculin expressions, versus graphite paper as a reference material. The results showed that MG-63 cells exhibited stronger cell adhesion, better proliferation and viability on GF, and osteoblasts cultured on GF exhibited vinculin expression throughout the cell body. The rougher and wrinkled surface morphology, higher elastic modulus and easy out-of-plane deformation associated with GF were considered to promote cell adhesion. Also, the biomineralization of GF was assessed by soaking in simulated body fluid, and the GF exhibited enhanced mineralization ability in terms of mineral deposition, which almost pervaded the entire GF surface. Our results suggest that graphene promotes cell adhesion, activity and the formation of bone-like apatite. This research is expected to facilitate a better understanding of graphene-cell interactions and potential applications of graphene as a promising toughening nanofiller in bioceramics used in load-bearing implants.

• Biomaterials and Biomechanics in Bioengineering
• /
• v.1 no.1
• /
• pp.1-12
• /
• 2014

Polymer multilayered hydrogels were prepared on a titanium alloy (Ti) substrate using a layer-by-layer (LBL) process to load a cell growth factor. Two water-soluble polymers were used to fabricate the multilayered hydrogels, a phospholipid polymer with both N, N-dimethylaminoethyl methacrylate (DMAEMA) units and 4-vinylphenylboronic acid (VPBA) units [poly(MPC-co-DMAEMA-co-VPBA) (PMDV)], and the polysaccharide alginate (ALG). PMDV interacted with ALG through a selective reaction between the VPBA units in PMDV and the hydroxyl groups in ALG and through electrostatic interactions between the DMAEMA units in PMDA and the anionic carboxyl groups in ALG. First, the Ti substrate was covered with photoreactive poly vinyl alcohol, and then the Ti alloy was alternately immersed in the respective polymer solutions to form the PMDV/ALG multilayered hydrogels. In this multilayered hydrogel, vascular endothelial growth factor (VEGF) was introduced in different layers during the LbL process under mild conditions. Release of VEGF from the multilayered hydrogels was dependent on the location; however, release continued for 2 weeks. Endothelial cells adhered to the hydrogel and proliferated, and these corresponded to the VEGF release profile from the hydrogel. We concluded that multilayered hydrogels composed of PMDV and ALG could be loaded with cell growth factors that have high activity and can control cell functions. Therefore, this system provides a cell function controllable substrate based on the controlled release of biologically active proteins.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.333-334
• /
• 2016

This paper proposes a new cascoded configuration for hybrid energy storage system (HESS) which consists of batteries and supercapacitor (SC) for Electric Vehicle applications. In this configuration,a resonant LLC converter is interfacedin series with a battery module and it converts a part of the energy from the batteries and transfer it to the dc-link bus. The LLC converter is controlled by a phase-shift angle between the primary and secondary switches to maintain a constant dc-link voltage and obtain soft-switching conditions for all the primary switches. By placing the SC moduleina cascoded concept, the rated voltage of SC can be reduced significantly compared with the conventional topologies. It helps save the cost and reduce the number of SC cells. The proposed configuration can operate with four different modes: feeding load, acceleration, regenerative braking andSC charging. A scaled-down prototype converter (2 kW, 600V output) is designed and tested to verify the advantages of the proposed topology. The maximum efficiency obtained with the proposed topology is 99%.

• CELLMED
• /
• v.2 no.3
• /
• pp.23.1-23.7
• /
• 2012

The healing properties of medicinal maggots (larval stage of Lucilia sericata) are widely used in the chirurgical debridement of non-healing wounds including diabetic foot ulcers, venous and pressure ulcers, where classical approaches have failed. Several kinds of wounds are prone to complications coming out of a specific wound bed environment. There are multi-resistant bacterial species present, their pathogenic impact is multiplied by their ability to form a biofilm. Moreover, immunological events in chronic wounds differ from those in acute wounds. Non-healing wounds are cycled in the early inflammation phase with increased levels of inflammation attributes like inflammation cytokines and matrix metalloproteinases produced by inflammation phase cells. Application of larval therapy promotes progress in the healing process to the next stages involving tissue granulation and re-epithelisation. Larval debridement is an effective method of cleaning the wound of cell debris, necrotic tissue and bacterial load. This happens in a mechanical and biological manner, but the whole complex mechanism of the maggot healing activity is still not fully elucidated. Centuries of clinical practice brings noticeable proof of the maggots' beneficial effect in wound healing management. This long history led to the investigation of the bioactive components of the larval body and its extracts in vitro. We introduce a review which describes the immunomodulation impact of maggot body components on the cellular and molecular levels of the wound healing process.

• Journal of Energy Engineering
• /
• v.11 no.3
• /
• pp.254-261
• /
• 2002

The fabrication method for the main components of the polymer electrolyte membrane fuel cell stack such as electrodes, membrane-electrode assemblies, and bipolar plates was established for the effective electrode area of 240 ㎠. A counter-flow type 100-cell stack was fabricated by using the above components and then a maximum power of 7.44 kW for H$_2$/O$_2$ and 5.56 kW for H$_2$/air could be obtained at 70$\^{C}$ and 1 atm. It was seen that the distribution of the OCV for unit cells in the stack was uniform but the voltage deviation increased as the load increased due to the IR drop and the electrode polarization. The stack was applied to the power source of the fuel cell/battery hybrid electric golf car. It produced about 1 kW at a room temperature operation during the test run, which occupied about 43% of the total power required by the 2.3 kW motor.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2002.11a
• /
• pp.74-80
• /
• 2002

A mathematical tension model for a moving web in a multi-span web handling system was derived and validated by using a simulator which includes unwinder, driven roller, winder, load cells, controllers, etc. A tension controller was designed to compensate tension disturbances generated by velocity changes of the unwinder and driven roller. From experimental results it was proved that the tension model properly expressed the tension behavior of a moving web for specific conditions. The distributed tension controller designed by using the pole-placement technique compensated the tension disturbances transfered from upsteram tension variation. Interactions between web spans including "tension transfer phenomenon" were clearly confirmed through the study. A mathematical model of lateral motion of a moving web was verified also by using the same experimental apparatus which includes displacement type guidance systems. And a feedforward control strategy was designed for more accurate control of the lateral motion of a moving web, which utilize a measured signal of the lateral displacement of web in a previous span and a more correctly identified mathematical model to estimate the disturbance of lateral motion from the previous span. This approach was turned out to be effective in improving the performance of the guidance system for more wide range disturbances.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.6
• /
• pp.1093-1099
• /
• 2009

Alternative energy sources such as renewable energy like solar power systems, wind power systems, or fuel cell power systems has been the rising issue in the electrical power system. This paper discusses an economic study analysis of fuel cells in the korean electricity market. It includes the basic concept of a fuel cell and the korean electricity market. It also describes the need of renewable energy and how the fuel cell is connected with the local grid. This paper shows the impact of production and recovering thermal energy of a grid-connected fuel cell power system. The profit maximization approach has been structured including electrical power trade with the local grid and heat trade within the micro-grid. The strategies are evaluated using a local load that uses electric and thermal power which has different patterns between summer and winter periods. The solution algorithm is not newly developed one, but is solved by an application called GAMS. Results indicate the need and usefulness of a fuel cell power system.