• 항공우주시스템공학회지
• /
• 제16권1호
• /
• pp.97-103
• /
• 2022

항공기에 장착되는 구성품은 항공기 운용 조건에서 구조 건전성이 입증되어야만 항공기에 장착될 수 있다. 항공기 주요 구성품 중에서 파일런은 엔진이나 외부무장 같은 외부장착물을 항공기의 주날개와 연결하고 파일런 자체에 작용하는 하중을 항공기의 주구조물로 전달하는 역할을 하며, 민간 항공기에서는 엔진 영역에서 화재가 발생할 경우 주날개로 화재가 번지는 것을 방지하는 역할도 한다. 본 연구에서는 항공기에 외부 연료탱크를 장착하기 위해 사용하는 연료 파일런의 구조 건전성을 검증하기 위해 수행한 구조 정적시험의 결과를 제시하였다. 본문에서는 파일런의 구조 정적시험에 사용되는 시험장비, 유압장치, 하중제어시스템 그리고 데이터 획득장비로 구성되는 시험셋업을 제시하였다. 그리고, 하중작동기를 제어하는 소프트웨어를 소개하고, 각 시험하중 조건에 대한 시험 프로파일을 제공하였다. 시험 결과, 각 시험에서 허용 오차 범위 내에서 하중작동기가 적절히 제어되는 것으로 나타났으며, 시험체의 주요 위치에서 수치해석과 구조시험으로 부터 획득한 변형률의 비교를 통해 수치해석의 신뢰성을 검증하였다. 결론적으로, 구조 정적시험을 통해 본 연구에서 다루고 있는 연료 파일런이 요구된 하중조건에 대해 충분한 구조 강도를 가지고 있음을 입증하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 추계학술대회
• /
• pp.561-565
• /
• 2006

The paper presents a method of assessing the adequate tapaclty of photovoltaic generation systems for public buildings based on analysis of load variation patterns of customers. When PV systems are installed for supplying power for the customer load, reverse power relay is required by the guideline to be installed at the point of common coupling with the power network. The suggested method analyzes daily, weekly and monthly load demand of the customer that Irishes PV system installation, and determines the appropriate rating of the PV system for preventing PV generation from exceeding the customer demand. This work is expected to support renewable energy dissemination projects of public organizations.

• 조명전기설비학회논문지
• /
• 제23권7호
• /
• pp.67-74
• /
• 2009

This paper describes the speed control functions of the typical steam turbine speed controllers and the test results of generator load rejection simulations. The goal of the test is to verify the speed controller's ability to limit the steam turbine's peak speed within a predetermined level in the event of generator load loss. During normal operations, the balance between the driving force of the steam turbine and the braking force of the generator load is maintained and the speed of the turbine-generator is constant. Upon the generator's load loss, in other word, the load rejection, the turbine speed would rapidly increase up to the peak speed at a fast acceleration rate. It is required that the speed controller has the ability to limit the peak speed below the overspeed trip point, which is typically 110[%] of rated speed. If an actual load rejection occurs, a substantial amount of stresses will be applied to the turbine as well as other equipments, In order to avoid this unwanted situation, not an actual test but the other method is necessary. We are currently developing the turbine control system for another nuclear power plant and have plan to do the simulation suggested in this paper.

• 드라이브 ㆍ 컨트롤
• /
• 제12권1호
• /
• pp.15-20
• /
• 2015

For testing a newly designed ship's steering gear, a steering gear test bench with a steering gear to be tested and a load generation part should be prepared. The load given to the steering gear has to be pertinent to the load generated in a targeted ship. In this study, the authors suggest a process of estimating the load given to steering gears in ships. At first, a test for measuring the load in the steering gear of a real ship was conducted. Then, a process was developed to compute rudder driving torque and force by using basic equations including some empirical equations on ship's steering. The test results and the computation results on the load in the steering gear were compared, As a result, the process suggested in this study for estimating load in ship's steering gears was verified.

• 한국멀티미디어학회논문지
• /
• 제18권12호
• /
• pp.1501-1508
• /
• 2015

In this paper, we describe a case study to improve performance through the load testing of multi-tired system for financial accounts before the system opening. The load test was conducted after the data collection tools(Performance Monitor, DB PSSDiag) were installed. By analyzing the collected log, we were able to identify the main sector requiring performance improvements among the presentation tier, web tier, business logic tier and data tier. The ASP.NET server-down on the web tier could be improved by modifying the parameter values in the configuration file. Some server downs occurred on the business logic tier when a large number of users access at the same time, were more difficult to be solved. By analyzing the hang-dump at the server-down time, we were able to find a process that caused the problem. and we had to modify the relevant codes. For major performance improvements of the data-tier, indices of some queries was optimized by using the built-in DBMS query analyzer, after analyzing the log of long-response-time queries. The problems and solutions considered in this case study will be a reference for the performance improvement of a multi-layer system with the similar structure.

• 한국안전학회지
• /
• 제38권3호
• /
• pp.61-68
• /
• 2023

This study performed a structural performance evaluation of a system scaffolding for elevator installation work developed in previous studies. The structural performance was evaluated via a structural test conducted to apply the working load specified in the design standard. The deflection of the horizontal member and the stress of each member constituting the system scaffolding were measured. Consequently, the structural safety evaluation including structural behavior and required performance was performed using the deflection and stresses measured from the structural test. The structural test and safety evaluation results based on the heavy working load corresponding to the design load indicated that the deflection, which is the performance criterion of the horizontal member, did not exceed the allowable value. Further, each member's stress, which is a safety evaluation indicator, did not exceed the allowable strength for both horizontal and vertical members with bending behavior and fordable bracing with tensile behavior, while also satisfying the required safety factor. In addition, the results confirmed the safety against deformation, partial damage, and destruction owing to excessive and maximum load. Therefore, the system scaffolding developed in this study satisfies both the structural performance and safety required by the design standards; thus, it can be applied to elevator installation work sites.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1434-1441
• /
• 2005

For anchored system applications, each ground anchor is tested after installation and prior to being put into service to loads that exceed the design. This load testing methodology, combined with specific acceptance criteria, is used to verify that the ground anchor can carry the design load without excessive deformations and that the assumed load transfer mechanisms have been properly developed behind the assumed critical failure surface. After acceptance, the ground anchor is stressed to a specified load and the load is locked-off. The two types of load tests conducted during the research program included performance test and creep test which were carried out in accordance with testing procedures by AASHTO(AASHTO 1990) and FHWA(Weatherby 1998) at Samsung-Dong 00 Site. Form the measurements, ultimate load and creep rate of anchors are proposed for straight shaft pressured grouted anchors in waste landfill. The load distribution on the grout was obtained from the measured strain data at each fraction of the ultimate load during the load tests.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.1105-1108
• /
• 2004

This paper describes the structural analysis result and load test result of accident EMU(Electric Multiple Units). Structural analysis and load test of EMU were performed for the criteria of safety assessment. Structural analysis using commercial I-DEAS software provided important information on the stress distribution and load transfer mechanisms as well as the amount of damages during rolling stock crash. The purpose of the load test is to evaluate a safety which carbody structure shall be considered fully sufficient rigidity so as to satisfy proper system function under maximum load and operating condition. The results have been used to provide the critical information for the criteria of safety assessment.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제17권3호
• /
• pp.207-212
• /
• 2017

Purpose: This article provides an efficient cushion molding method for improving reliability of the rotation driving system. Method: Allowable stress level for cushion is calculated by using physical characteristics of the rotation driving system. In addition, various test units are manufactured and used to conduct the rebound resilience, the burst pressure and the alternating load test. Results: Actual allowable stress level and test results of the rebound resilience, the burst pressure and the alternating load test are provided. Conclusion: The cushion manufactured by the compression molding method gives more preferable characteristics for improving the reliability of the rotation driving system.

• 산업기술연구
• /
• 제15권
• /
• pp.187-193
• /
• 1995

In this paper, a short-term load forecasting expert system considering the load variation due to the change in temperature is presented. The change in temperature is an important load variation factor that varies the normal load pattern. The conventional load forecasting methods by artificial neural networks have used the technique where the temperature variables were included in the input neurons of artificial neural networks. However, simply adding the input units of temperature data may make the forecasting accuracy worse, since the accuracy of the load forecasting in this method depends on the accuracy of weather forecasting. In this paper, the fuzzy expert system that modifies the forecasted load using fuzzy rules representing the relations of load and temperature is presented and compared with a conventional load forecasting technique. In the test case of 1991, the proposed model provided a more accurate forecast than the conventional technique.