• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1819-1826
• /
• 2007

This study results of performed field load test in order to estimate the best pile length assessment and allowable bearing capacity of the pile foundation. End of initial driving(EOID) and restrike of pile dynamic loading tests were performed to calculate allowable bearing capacity of the experimental pile side and results were compared with the allowable bearing capacity estimated by theory. The results of allowable bearing capacity by EOID test is $1.08{\sim}1.21$ in the range of compared to the capacity calculated by the Structure Foundation Design Criterion. Allowable bearing Capacity by restrike of pile dynamic loading test is $1.32{\sim}1.48$ in the range of compared to the Structure Foundation Design Criterion. The Foundation Design Criterion underestimated the pile capacity. If the bearing capacity calculated by Structure Foundation Design Criterion is 100, EOID of pile dynamic loading test is 116, restrike of pile dynamic loading test is 138 for 20m pile used in this experimental.

• KSTLE International Journal
• /
• 제1권2호
• /
• pp.107-112
• /
• 2000

In case of the limitation of Deep RIE fabrication far Micro Gas Turbine, bearing aspect ratio is limited in very small value. The characteristics such as pressure distribution, load capacity and non-linearity of a short bearing of L/D=0.083 and a conventional bearing of L/D=1.0 with coupled boundary effects are investigated for Micro Gas Turbine bearings. The coupled effect was analyzed by mass conservation at coupled end area. The results, increasing load capacity and non-linearity due to the coupled effect of thrust and journal bearing, are obtained and the selection of journal bearing type is discussed.

• Tribology and Lubricants
• /
• 제17권6호
• /
• pp.467-475
• /
• 2001

Feasibility study of gas-lubricated bearing in micro gas turbine was performed. Based on Reynolds equation, finite difference method with coupled boundary was developed to analyze bearing characteristics, such as load capacity, mass flow rates and stiffness. By the bearing force and mass flow rates analysis with the variation of supply pressure, bearing clearance and capillary radius, acceptable range of design parameters were suggested in terms of load capacity and stiffness of bearings. Additionally, coupled boundary effect on pressure distribution was investigated and it is stated that coupling could reduce an excitation force due to narrow pressure distribution.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.273-281
• /
• 2001

Feasibility study of gas-lubricated bearing in micro gas turbine was performed. Based on Reynolds equation, finite difference method with coupled boundary was developed to analyze bearing characteristics, such as load-carrying capacity, mass flow rates and stiffness. By the bearing force and mass flow rates analysis with the variation of supply pressure, bearing clearance and capillary radius, acceptable range of design parameters were suggested in terms of load capacity and stiffness of bearings. Additionally, coupled boundary effect on pressure distribution was investigated and it is stated that coupling could reduce all excitation force due to narrow pressure distribution.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제32회 추계학술대회 정기총회
• /
• pp.243-249
• /
• 2000

In case of the limitation of Deep RIE fabrication for Micro Gas Turbine, bearing aspect ratio is limited in very small value. The characteristics such as pressure distribution load capacity and non-linearity of a short bearing of L/D=0.083 and a conventional bearing of L/D=1.0 with coupled boundary effects are investigated far Micro Gas Tlubine bearings. The coupled efffect was analyzed by mass conservation at coupled end area. The results, increasing load capacity and non-linearity due to the coupled effect of thrust and journal bearing, are obtained and the selection of journal bearing type is discussed.

• 한국지반환경공학회 논문집
• /
• 제5권3호
• /
• pp.5-15
• /
• 2004

SIP 공법이 국내에서 저소음 저진동 말뚝공법으로 널리 사용되고 있지만 품질관리기준이 명확히 정립되지 못하고 실무자들의 공법의 원리에 대한 이해 부족으로 시공시 혼선을 초래하고 있어 공법이 본래 가진 지지력을 충분히 발휘되지 못하고 있다. 이러한 문제점을 개선하기 위하여 2002년에 대한주택공사에서는 SIP 공법의 시공 및 재하시험기준을 개선하였다. 개선된 기준에 의하여 현장에 시공된 SIP 말뚝에 대하여 재하시험을 통하여 지지력을 평가한 결과 이전 방법으로 시공된 말뚝에 비하여 시공하중의 설계만족도 및 지지력 특성이 크게 향상된 것을 확인할 수 있었으며 이를 설계에 반영하면 기초 공사비도 절감할 수 있는 것으로 나타났다. 향상된 지지력 특성을 설계에 반영하기 위하여 재하시험결과를 국내에서 많이 사용하고 있는 말뚝 설계식들과 신뢰성 분석을 실시하여 적합식을 찾고자 하였다. 분석결과 개선된 기준으로 시공된 SIP 말뚝은 Meyerhof(1976)의 타입말뚝 설계식과 유사한 지지거동을 하는 것으로 나타났다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.666-672
• /
• 2010

Load bearing capacity of new lattice girder has been evaluated with optimized spider for lattice girder utilized in the construction of tunnels. This newly developed lattice girder is different from existing lattice girder as its design is associated with existing spider with newly developed 2 types of form. The spacing of lattice girder's spider is linked with the weight and it decides the unit cost and construction therefore, different spacing of the developed spider has been produced to evaluate the measurement of load bearing capacity. As the result of the tests by producing the spacing of spider as 0cm and 4cm for developed lattice girder-2, the load bearing capacity of 0cm with spacing of 21%, and 4cm with 25% of increase when they are compared with the existing lattice girder, and the weight of specimen was decreased. As the result of the tests by producing the spacing of 1cm and 6cm for developed lattice girder-3, the spacing of 1cm with 42%, and the spacing of 6cm with 11% of increase which presented higher load bearing capacity in all newly developed forms, and there was a certain degree of increase in weight in case of 1cm of spacing. The result of evaluation regarding on the displacement by applying the evaluation method suggested by the German Railroad administration, the entire specimens were found to satisfy all the evaluation standard suggested by the administration.

• 지질공학
• /
• 제30권4호
• /
• pp.635-648
• /
• 2020

본 연구는 회전관입말뚝의 이음부를 용접이나 볼트가 필요 없는 육각형 이음부로 개선하여 압축재하시험을 수행하였다. 또한 인발시험의 경우 기존 방법과 유사하게 볼트체결 방법으로 적용하여 인발시험을 수행하였다. 회전관입말뚝의 지지력을 평가하기 위해 현장시험 2지역을 선정하였다. 하중재하시험은 정재하시험과 인발시험을 수행하였으며 회전관입말뚝에 대한 지지력을 평가하였다. 현장시험결과, 정재하시험시 중력식 그라우트를 적용한 말뚝에서 AC 358 Code에 따른 지지력평가 결과 600 kN 이상으로 나타났으며, 그라우트가 없는 말뚝에서는 600 kN 이하의 지지력을 보여 중력 그라우팅이 필요함을 확인하였다. 또한 현장시험결과를 고려하여 지지력을 평가하였으며, 적은 표본에 의해서 도출된 결과로 추후 기초자료로 활용될 수 있을 것으로 판단된다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.20-27
• /
• 2004

Reinforced twice than width of foundation with SIC under steel piles drived in cohesion soil and in the coal-limestone which heavily fractured. To analyze behaviour characteristic of steel piles, load transfer test was performed to steel piles attached with strain gauges to axial direction. After it passed 49days, dynamic load test was performed to set-up effect of steel piles bearing capacity. The results of test were compared to each other. According to the results, as the skin friction of steel pile was on the same condition, end bearing capacity of steel piles established on SIC solid of cemented milk in cohesion soil was three times than steel piles established on SIG solid of cemented milk in heavily fractured coal- limestone. After piles were driven and passes 49days, in case of piles on SIG solid of comented milk in cohesion soil the increaes of allowable bearing capacity was 442.9% and allowable bearing capacity of piles on SIG solid of cemented milk in heavily fractured coal-limestone increased 22.4%.

• Steel and Composite Structures
• /
• 제28권2호
• /
• pp.167-177
• /
• 2018

In order to investigate mechanical properties in the core area of Square Hollow Section(SHS) column connection with external stiffening ring, four specimens were tested under the static tension load. The failure modes, load-displacement curves and strain distribution were analyzed to study the mechanical properties and the load transfer mechanism of the core area of connections. The connections behave good ductility and load-bearing capacity under the static tension load. Parametric analysis was also conducted, in which the thickness of steel tube, extended width and thickness of the stiffening ring were considered as the parameters to investigate the effects on mechanical properties of the connections. Based on the experimental results, an analytical method for the bearing capacity of connection with external stiffening ring under the static tension load was proposed. The theoretical results and the experimental results are in good agreement, which indicates that the theoretical calculation method of the bearing capacity is advisable.