• Journal of Power Electronics
• /
• v.7 no.4
• /
• pp.343-352
• /
• 2007

This paper proposes a modularized charge equalization converter for hybrid electric vehicle (HEV) lithium-ion battery cells, in which the intra-module and the inter-module equalizer are Implemented. Considering the high voltage HEV battery pack, over approximately 300V, the proposed equalization circuit modularizes the entire $M^*N$ cells; in other words, M modules in the string and N cells in each module. With this modularization, low voltage stress on all the electronic devices, below roughly 64V, can be obtained. In the intra-module equalization, a current-fed DC/DC converter with cell selection switches is employed. By conducting these selection switches, concentrated charging of the specific under charged cells can be performed. On the other hand, the inter-module equalizer makes use of a voltage-fed DC/DC converter for bi-directional equalization. In the proposed circuit, these two converters can share the MOSFET switch so that low cost and small size can be achieved. In addition, the absence of any additional reset circuitry in the inter-module equalizer allows for further size reduction, concurrently conducting the multiple cell selection switches allows for shorter equalization time, and employing the optimal power rating design rule allows fur high power density to be obtained. Experimental results of an implemented prototype show that the proposed equalization scheme has the promised cell balancing performance for the 7Ah HEV lithium-ion battery string while maintaining low voltage stress, low cost, small size, and short equalization time.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.620-627
• /
• 1999

Electrochemical properties of the Al current collector being used in lithium ion batteries have been studied in the 4 different aprotic electrolytes(1 M $LiBF_4$ EC : DMC, 1 M $LiBF_4$ EC : EMC. 1 M $LiPF_6$ EC : DMC. 1 M $LiPF_6$ EC : EMC) employing cyclic voltammetry and impedance measurement. Al electrode showed a wide range of the electrochemical window(0.5~4.1 V vs. $Li/Li^{+}$). However, solid interfacial materials has been formed on the Al surface due to reduction of impurities($H_2O$, $O_2$, etc), lithium salts, and electrolytes at low applied potentials, and aluminum oxides in the highly oxidizing potential as well. Especially, Al current collector was susceptible to localized in consequence of impurities in electrolytes.

• Resources Recycling
• /
• v.9 no.4
• /
• pp.37-43
• /
• 2000

Leaching of $LiCoO_2$ as a cathodic active materials for recovering Li and Co from spent lithium ion battery was investigated in terms of reaction variables. At the optimum condition determined in the previous work, Li and Co in a $H_2SO_4$ and $HNO_3$ solution were dissolved 70~80% and 40%, respectively. Li and Co were leached over 95% with the addition of a reductant such as $Na_2S_2O_3$ or $H_2O_2$. This behavior is probably due to the reduction of $Co^{3+}$ to $Co^{2+}$. Leaching of $LiCoCo_2$ powder obtained by calcination of an electrode materials from spent batteries was also carried out. Leaching efficiency of Li and Co were over 99% at the optimum condition with $H_2O_2$ addition of 1.7 vol.%. It seems to be due to the activation of $LiCoO_2$ by repeated charging and discharging or an imperfect crystal structure by deintercalation of Li.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.1
• /
• pp.78-85
• /
• 2019

The effect of various lithium sources such as LiCl, LiOH, and Li-metal on the microstructure and electrochemical properties of granulated $SiO_x$ powders were investigated. Various lithium sources were metallurgically added for a passive pre-lithiation of $SiO_x$ to improve its low initial coulombic efficiency. In spite of using the same amount of Li in various sources, as well as the same process conditions, different lithium silicates were obtained. Moreover, irreversible phases were formed without reduction of $SiO_x$, which might be from additional oxygen incorporation during the process. Accordingly, there were no noticeable electrochemical enhancements. Nevertheless, the $Li_4SiO_4$ phase changes the initial electrochemical reaction, and consequently the relationship between the microstructure and electrochemical properties of metallurgically pre-lithiated $SiO_x$ could provide a guideline for the optimization of the performance of lithium ion batteries.

• Journal of the Korean Electrochemical Society
• /
• v.22 no.3
• /
• pp.128-137
• /
• 2019

A lithium is the lightest metal on the earth. It has some attractive characteristics as a negative electrode material such as a low reduction potential (-3.04 V vs. SHE) and a high theoretical capacity ($3,860mAh\;g^{-1}$). Therefore, it has been studied as a next generation anode material for high energy lithium batteries. The thin lithium electrode is required to maximize the efficiency and energy density of the battery, but the physical roll-press method has a limitation in manufacturing thin lithium. In this study, thin lithium electrode was fabricated by electrodeposition under various conditions such as compositions of electrolytes and the current density. Deposited lithium showed strong relationship between process condition and its characteristics. The concentration of electrolyte affects to the shape of deposited lithium particle. As the concentration increases, the shape of particle changes from a sharp edged long one to a rounded lump. The former shape is favorable for suppressing dendrite formation and the elec-trode shows good stripping efficiency of 92.68% (3M LiFSI in DME, $0.4mA\;cm^{-2}$). The shape of deposited particle also affected by the applied current density. When the amount of current applied gets larger the shape changes to the sharp edged long one like the case of the low concentration electrolyte. The combination of salts and solvents, 1.5M LiFSI + 1.5M LiTFSI in DME : DOL [1 : 1 vol%] (Du-Co), was applied to the electrolyte for the lithium deposition. The lithium electrode obtained from this electrolyte composition shows the best stripping efficiency (97.26%) and the stable reversibility. This is presumed to be due to the stability of the surface film induced by the Li-F component and the DOL effect of providing film flexibility.

• Archives of Pharmacal Research
• /
• v.29 no.10
• /
• pp.840-844
• /
• 2006

For the exploration of pharmacophoric moiety of malloapelta B (1) possessing the inhibitory activity of $NF-{\kappa}B$ activation, structural variation of ${\alpha},{\beta}-unsaturated$ carbonyl motif was attempted. 1 was reduced by catalytic hydrogenation, sodium borohydride, and lithium aluminumhydride. Catalytic hydrogenation with 30 psi or 15 psi of $H_2$ gas of 1 generated 8-butyl-5,7-dimethoxy-2,2-dimethylchroman (2) and 1-(5,7-dimethoxy-2,2-dimethylchroman-8-yl)butan-1-one (3), respectively. Reduction with sodium borohydride occurred at the double bond of ${\alpha},{\beta}-unsaturated$ ketone of 1 to give 1-(5,7-dimethoxy-2,2-dimethyl-2H-chromen-8-yl)butan-1-one (4). Reduction of 1 with lithium aluminumhydride and then quenched with methanol and water produced unexpected products, 1-(5,7-dimethoxy-2,2-dimethyl-2H-chromen-8-yl)-3-methoxy-1-butene (5) and 1-(5,7-dimethoxy-2,2-dimethyl-2H-chromen-8-yl)-3-hydroxy-1-butene (6). These are formed from the isomerization of initial product 9 through the continuous conjugate carbocation intermediate 11. Addition of ethylmagnesium bromide and dimethyl malonate anion to 1 gave the conjugate adducts 7 and 8. Ethylmagesium bromide and sodium borohydride reduction unusually gave the conjugate addition due to steric congestion around carbonyl group of 1. Compound 2 exhibits the reduced inhibitory activity against $NF-{\kappa}B$ activation and the others do not show the activity. Therefore ${\alpha},{\beta}-unsaturated$ carbonyl group of 1 should be important for its inhibitory activity.

• Bulletin of the Korean Chemical Society
• /
• v.15 no.10
• /
• pp.881-888
• /
• 1994

The approximate rates and stoichiometry of the reaction of excess sodium tris(diethylamino)aluminum hydride (ST-DEA) with selected organic compounds containing representative functional groups under standardized conditions(tetrahydrofuran, $0{\circ}$) were studied in order to characterize the reducing characteristics of the reagent for selective reductions. The reducing ability of STDEA was also compared with those of the parent sodium aluminum hydride (SAH) and lithium tris(diethylamino)aluminum hydride (LTDEA). The reagent appears to be milder than LTDEA. Nevertheless, the reducing action of STDEA is very similar to that observed previously for LTDEA, as is the case of the corresponding parent sodium and lithium aluminum hydrides. STDEA shows a unique reducing characteristics. Thus, benzyl alcohol, phenol and 1-hexanol evolved hydrogen slowly, whereas 3-hexanol and 3-ethyl-3-pentanol, secondary and tertiary alcohols, were essentially inert to STDEA. Primary amine, such as n-hexylamine, evolved only 1 equivalent of hydrogen slowly. On the other hand, thiols examined were absolutely stable. STDEA reduced aidehydes and ketones rapidly to the corresponding alcohols. The stereoselectivity in the reduction of cyclic ketones by STDEA was similar to that by LTDEA. Quinones, such as p-benzoquinone and anthraquinone, were reduced to the corresponding 1,4-dihydroxycyclohexadienes without evolution of hydrogen. Carboxylic acids and anhydrides were reduced very slowly, whereas acid chlorides were reduced to the corresponding alcohols readily. Esters and epoxides were also reduced readily. Primary carboxamides consumed hydrides for reduction slowly with concurrent hydrogen evolution, but tertiary amides were readily reduced to the corresponding tertiary amines. The rate of reduction of aromatic nitriles was much faster than that of aliphatic nitriles. Nitrogen compounds examined were also reduced slowly. Finally, disulfide, sulfoxide, sulfone, and cyclohexyl tosylate were readily reduced without evolution of hydrogen. In addition to that, the reagent appears to be an excellent partial reducing agent: like LTDEA, STDEA converted ester and primary carboxamides to the corresponding aldehydes in good yields. Furthermore, the reagent reduced aromatic nitriles to the corresponding aldehydes chemoselectively in the presence of aliphatic nitriles. Consequently, STDEA can replace LTDEA effectively, with a higher selectivity, in most organic reductions.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.646-651
• /
• 2008

The electrolytic reduction of spent oxide fuel involves the liberation of oxygen in a molten LiCl electrolyte, which results in a chemically aggressive environment that is too corrosive for typical structural materials. It is essential to choose the optimum material for the process equipment handling molten salt. IN713LC is one of the candidate materials proposed for application in electrolytic reduction process. In this study, yttria-stabilized zirconia (YSZ) top coat was applied to a surface of IN713LC with an aluminized metallic bond coat by an optimized plasma spray process, and were investigated the corrosion behavior at $675^{\circ}C$ for 216 hours in the molten salt $LiCl-Li_2O$ under an oxidizing atmosphere. The as-coated and tested specimens were examined by OM, SEM/EDS and XRD, respectively. The bare superalloy reveals obvious weight loss, and the corrosion layer formed on the surface of the bare superalloy was spalled due to the rapid scale growth and thermal stress. The top coatings showed a much better hot-corrosion resistance in the presence of $LiCl-Li_2O$ molten salt when compared to those of the uncoated superalloy and the aluminized bond coatings. These coatings have been found to be beneficial for increasing to the hot-corrosion resistance of the structural materials for handling high temperature lithium molten salts.

• Bulletin of the Korean Chemical Society
• /
• v.8 no.3
• /
• pp.162-165
• /
• 1987

The reduction rate of borohydride exchange resin (BER) was greatly enhanced in the presence of lithium salts. Thus 2-heptanone was reduced completely with BER-LiCl in 1 h at room temperature. However, no reduction was observed with BER alone under the same conditions. With this system, organic compounds containing various fuctional groups were examined in ethanol at room temperature. This study revealed that BER-LiCl system exhibits an excellent chemoselectivity for carbonyl group in the presence of other functional groups. Keto esters and epoxy ketones were reduced with BER-LiCl to give the corresponding hydroxy esters and epoxy alcohols with excellent yields. Selective reductions of carbonyl groups were also possible in the presence of other organic compounds containing functional groups such as 1-idooctane, 1-bromooctane, caproamide, hexanenitrile, nitrobenzene, n-butyl disulfide, dimethyl sulfoxide and 1-dodecene.

• Applied Chemistry for Engineering
• /
• v.8 no.6
• /
• pp.1022-1028
• /
• 1997

This work was performed to study the characteristics of electrochemical intercalation reactions occurring at the interface between the organic electrolyte and tungsten trioxide thin film (thickness of $4000{\AA}$) prepared by e-beam evaporation method as cathodically coloring oxide with regard to the electrochromism by the intercalating reactions of the lithium cation in the 1M $LiClO_4/PC$ organic solution. The characteristics of electrochemical intercalation reactions were investigated by various DC electrochemical methods such as cathodic Tafel polarization test, multiple and the single sweep cyclic voltammetry and the coulomety titrations method. The surfaces of thin films were observed with the patterns of X ray diffraction after the coloring and bleaching reactions. In comparison with the previous results that $WO_3$ thin film intersely detached from the surface of electrode when the hydrogen cation was intercalated into $WO_3$ thin film in the o.1N $H_2SO_4$ aqueous solution, the intercalation reaction of lithium cation into $WO_3$ thin film in the 1M $LiClO_4/PC$ organic solution was shown that the stable bleaching and coloration was appeared within 1.0V of the applied overpotential. When the overpotential of electrochromic reaction for lithium cation in the 1M $LiClO_4/PC$ organic solution had been applied up to 1.5V, the accumulation phenomenon of lithium in amorphous $WO_3$ thin film layer occurred because the inserted lithium into amorphous $WO_3$ thin layer for coloring process was not fully removed from the thin layer to the electrolyte during bleaching process. It was found that there is a limitation of applied overpotential for coloring process by the reduction of the current densities of bleaching and coloration after few number of coloring and bleaching cycles.