• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.252-259
• /
• 2001

It is derived for the temperature profile in a cylindrical and planar shape capillary pumped loop evaporators subject to a uniform heat flux prior to the initiation of boiling using the finite difference method. The results of the analysis allow for the determination of applied power levels for which nucleation is likely to occur only within the vapor grooves of the evaporator while maintaining subcooling in the liquid core, thereby increasing the likelihood of a successful startup. Also, limits are found for which additional increases in the applied heat flux do not increase the temperature difference between the vapor grooves and the wick-liquid core interface. Several advantages of larger diameter evaporators observed experimentally in startup are explained and quantified by the model. This analysis is appropriate for standard capillary pumped loop evaporators during a fully-flooded startup as well as starter pump designs and loop heat pipes.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.546-552
• /
• 2001

The heat transfer and flow measurements on a pedestal encountered in chip cooling. A uniform wall temperature boundary condition at the plate surface and on a pedestal was created using shroud method. Liquid crystal was used to measure the plate surface temperature. The jet Reynolds number (Re) ranges from 11,000 to 50,000, the dimensionless nozzle-to-surface distance (L/d) from 2 to 10, and the dimensionless pedestal diameter-to-height (H/D) from 0 to 1.0. The results show that the Nusselt number distributions at the near the pedestal exhibit secondary maxima at $r/d{\cong}1.0\;and\;1.5$. The formation of the secondary maxima is attributed to an create in the vortex by the pedestal.

• 대한기계학회논문집
• /
• 제15권2호
• /
• pp.685-692
• /
• 1991

The pool boiling behavior of a heated surface has been investigated experimentally, focusing on the cases when only a part of the contact surface is heated. Characteristic boiling curves are obtained with circular metal surface test pieces heated below while immersed in Refrigerant-113. Locally heated test pieces are fabricated by inserting a heating block at the center inside a larger conducting block. Overall heat transfer rates are measured while the experimental conditions are systematically varied. The local temperature profiles along the radius are measured for conducting blocks. It is found that the conjugated boiling condition exists and the total heat fluxes should be correlated to a suitably defined temperature difference.

• 한국수정란이식학회지
• /
• 제16권3호
• /
• pp.233-237
• /
• 2001

To develop an effective vitrification method, we examined the use of a conventional straw as vessel fur vitrification of mouse oocytes, and to compare the post-thaw survival and chromosome configuration of these oocytes with those vitrified in grids. Intact cumulus-enclosed oocytes were vitrified with DPBS with 5.5 M ethylene glycol and 1.0 M sucrose, and loaded into straws and onto eletron microscopic copper grid fur storing in liquid nitrogen. Intact vitrified and thawed oocytes were karyotying for chromosome. The rates of post-thawed survival were 88.5% in vitrified oocytes with straws, and 83% in vitrified ooctyes with grids. Vitrified and thawed oocytes with straws and grids were increased chromosomal abnormality (31.4% and 30.9%) compared with fresh oocytes (17.8%). The conventional straws can be used as vessel for vitrification to prevent of inflection in liquid nitrogen.

• 설비공학논문집
• /
• 제15권2호
• /
• pp.126-131
• /
• 2003

Convective instability driven by surface tension is analyzed in an initially quiescent water absorbing ammonia gas with heat transfer using the linear stability analysis. The propagation theory is adapted to find the critical conditions of the onset of Marangoni convection. In this theory, the solutal penetration depth is chosen as the length scale factor. The results show that the liquid layer becomes more stable with decreasing the Schmidt number and increasing the Lewis number. It is also found that there is a critical Biot number to make the liquid layer be most unstable, and there is a linear relationship between the thor-mal Marangoni number and the solutal Marangoni number.

• 한국환경과학회지
• /
• 제6권1호
• /
• pp.25-31
• /
• 1997

The variations of gas hold-up, overall volumetric oxygen mass transfer coefficients and liquid circulation velocity in an internal loop reactor were investigated to manifest scale-up effect. The relationship between superficial gas velocity and gas hold-up were found as Ugr = 0.045 $\varepsilon$r in the pilot-scale and Ugr = 0.056 $\varepsilon$r in the bench-scale reactor. The overall volumetric oxygen mass tractsfer coefficient, KLa was slightly increased in the pilot-scale than in the bench-scale reactor. Flow regime was changed from the bubble flow to the churn-turbulent flow when the superficial gas velocity reached to 3.5 - 4 cm/sec in the pilot-scale.

• 대한설비공학회지:설비저널
• /
• 제17권2호
• /
• pp.140-149
• /
• 1988

The problem of heat and mass transfer accompanying the absorption of water vapor into LiBr-$H_2O$ liquid solution flowing over the outside of the horizontal cylinder was theoretically studied to understand the absorption process occuring in the absorber of the absorption heat pump. Numerical results are presented for various quantities of interest relating to temperature, concentration, heat flux and mass flux. Also, the effects of mass flowrate, initial average velocity, and the radius of the cylinder were investigated.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.1153-1158
• /
• 2009

The performance of louver-finned flat-tube and fin & tube radiators for computer CPU liquid cooling were experimentally investigated. In this study, 7 samples of radiators with different shape and pass number (1, 2, 10) were tested in a wind tunnel. The experiments were conducted under the different air velocity range from 1 to 4 m/s. The water flow rate through a pass was 1.2 LPM. Inlet temperatures of air and water were $20^{\circ}C$ and $30^{\circ}C$ respectively. It was found that the best performance was observed in the louver-finned flat-tube sample considering pressure drop and heat transfer coefficient.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1999년도 추계 학술대회논문집
• /
• pp.65-70
• /
• 1999

Radiative heating of a liquid rocket base plane due to plume emission is numerically investigated. Calculation of flow and temperature fields around rocket nozzle precedes and thereby realistic plume shape and temperature distribution inside the plume are obtained. Based on the calculated temperature field, radiative transfer equation is solved by discrete ordinate method. The averaged radiative heat flux reaching the base plane is about $5kW/m^2$ at the flight altitude of 10.9km. This value is small compared with radiative heat flux caused by constant-temperature (1500K) plume emission, but it is not negligibly small. At higher altitude (29.8km), view factor between the babe plane and the exhaust plume is increased due to the increased expansion angle of the plume. Nevertheless, the radiative heating disappears since the base plane is heated to high temperature (above 1000K) due to convective heat transfer.

• 한국수정란이식학회지
• /
• 제4권1호
• /
• pp.35-40
• /
• 1989

The effects of cryoprotectants (glycerol, DMSO and ethylene glycol) and the concentrations (0, 0, 25, 0.5and 1.0 M) of sucrose in the diluent on the is vitro survival of mouse morulae froaen rapidly in liquid nitrogenvapour were examined. When the embryos were equilibrated in 1.5 M cryoprotectants +0.25 M sucrose in one-step or in 3.0 M cryoprotectants +0.25 sucrose in two-step and diluted with 0, 0.25, 0.5, or 1.0 M sucrose solution after thawing, high survival rates were obtained in ethylene glycol (48.0% to 88.2 %) or in glycerol (35.0 % to 77.8 %). These results show that 1.5 M ethylene glycol is a highly efficient cryoprotective agent for the rapid freezing of mouse morula embryos and 0.5 M sucrose was optimal concentration in the diluent after thawing.