• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.109-115
• /
• 2004

A 1-D system design program has been developed for the preliminary design of the turbopump system in liquid rocket engines, which use LOx and kerosene as propellants. Gasgenerator cycle and staged combustion cycle were considered as turbopump type liquid rocket engine systems. In the system analysis, mass flow balance, thrust, specific impulse, mixture ratios, turbopump power, and turbine expansion ratio of engine system were analyzed. Results show that most of the parameters agree well with real engine parameters except gasgenerator. Therefore, the l-D system design program developed in this study can be used to derive the preliminary design parameters of a turbopump with any thrust level liquid rocket engine.

• Journal of Aerospace System Engineering
• /
• v.9 no.1
• /
• pp.1-6
• /
• 2015

A critical speed analysis of oxidizer pump was peformed for a 7 ton class liquid rocket engine as the third stage engine of the Korea Space Launch Vehicle II. Based on the previously developed experimental 30 ton class turbopump and presently developing 75 ton class turbopump for the first and second stage rocket engine of Korea Space Launch Vehicle II, a layout and configuration of the 7 ton class turbopump rotor assembly are determined. A ball bearing stiffness analysis and rotordynamic analysis are performed for both of the bearing unloaded condition and loaded condition. Structural flexibility of the oxidizer pump casing is also included to predict critical speeds. From the numerical analysis, it is confirmed that the rotor system acquires sufficient separate margin of critical speed as a sub-critical rotor even though decrease of critical speed due to the casing structural flexibility.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.33 no.12
• /
• pp.933-938
• /
• 2009

Hot test of a full-scale turbopump for a 30-ton-thrust liquid rocket engine was carried out. The turbopump is composed of an oxidizer pump, a fuel pump, and a turbine on a single shaft. Model fluid was used in the test, that is, hot air for the turbine and water for the pumps. The turbopump was operated stably at full speed for 120 seconds. In terms of performance characteristics of pumps and turbine, the results from the turbopump assembly test are compared with those from the turbopump component tests which were performed at about half of the design rotational speed.

• Journal of Aerospace System Engineering
• /
• v.4 no.1
• /
• pp.1-9
• /
• 2010

As the rocket KSLV-1 called NARO was launched lately, development of domestic rocket technology has been accelerated elastically. Since the rocket technology needs a lot of empirical data, a variety of experiments should be done and lots of time have to be spent for accumulating the foundation of technology. However using a computer can be the solution to close a gap of technique because the simulation can be executed in short time against real experiments and calculate a multiplicity of cases easily. In this research, the transient analysis of turbopump-fed liquid rocket system was worked by the one dimensional modeling. The rocket system consists of the modulized components that are engine, turbopump and so on. For 70 ton class system, the rocket transient process of starting was studied and the performance analysis in steady condition was achieved. In addition, the estimation of nozzle internal flow was investigated by using a nozzle coefficient.

• Journal of Aerospace System Engineering
• /
• v.7 no.4
• /
• pp.49-54
• /
• 2013

A turbopump for a 75 ton class liquid rocket engine was tested at full speed for 20 seconds using model fluid. Liquid nitrogen is used for the oxidizer pump, water for the fuel pump, and hot gas for the turbine. The non-cavitating head of pump from the turbopump assembly test showed a good agreement with that from the pump component test. The relative difference of turbine efficiency between the turbopump assembly test and the turbine component test was 0.3% only. Suction performance from the turbopump assembly test was higher than that of pump component test, which resulted from the thermodynamic effect of cavitation.

• Journal of Aerospace System Engineering
• /
• v.1 no.4
• /
• pp.42-45
• /
• 2007

The process of Lay-out design and assembly for liquid rocket engine was presented and the Lay-out design for main components of liquid Rocket engine system was studied. Vertical direction is recommended in the case of turbopump's arrangement. If the length of pipe between gas-generator with turbopump's turbine is shorter, gas-generator is stable. The arrangements of main valves are recommended as near disposition to combustion chamber, because shut-down process time is shorter. Interference with launch vehicle and structural strength considering gimbal actuator's force and control performance is considered in the case of gimbal actuator's supporter design.

• Journal of Aerospace System Engineering
• /
• v.3 no.2
• /
• pp.20-23
• /
• 2009

The structural analysis of liquid rocket engine was performed in the case of sinusoidal vibration load to verify structural safety. The finite element model is composed with main liquid rocket engine components, combustion chamber, turbopump, gas-generator, pyro-starter, main pipes, main valve, heat-exchanger, gimbal-mount and brackets. Natural vibration mode analysis and structural analysis for sinusoidal vibration load were performed. The natural mode frequency of liquid rocket engine is twice than that of launch vehicle. In the case of stress result of sinusoidal vibration load, the part of maximum stress has 1.4 margin, so the engine structure is safe for sinusoidal vibration load.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.93-100
• /
• 2020

The turbopump of the liquid rocket engine adapts an inducer to minimize the cavitation due to the variations of the propellants supply condition. However, the inducer introduces cavitation instabilities which are well-known problems in the engine development. In this paper, operational characteristics by the cavitation instabilities are analyzed and the reliability of the engine is checked when the first stage engine of the KSLV-II is tested at the low inlet pressure conditions. The characteristic frequencies representing the cavitation instabilities of the LOx pump are clearly found in various high frequency sensor signals around the entire engine in addition to the LOx and fuel pump.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.11-15
• /
• 2012

A rotordynamic analysis is performed for a 7 ton class turbopump applied to the third stage LRE(Liquid Rocket Engine) of the KSLV(Korea Space Launch Vehicle). Based on the heritage of the developed experimental 30 ton class turbopump and developing 75 ton class turbopump for the KSLV first and second stage LRE, the 7 ton class turbopump is designed as an one-axis rotor turbopump. Two rotor systems comprised of one oxidizer pump assembly and the other fuel pump-turbine assembly are connected each other using a spline shaft and operating at a design speed. Through the rotordynamic analysis, it is investigated that the turbopump acquires sufficient separate margin of critical speed as a sub-critical rotor.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.2
• /
• pp.56-61
• /
• 2011

Performance test of a full-scale turbopump assembly for a 75 ton class liquid rocket engine was carried out at full speed. Model fluid was used as a working medium: liquid nitrogen for the oxidizer pump, water for the fuel pump, and hot air for the turbine. The turbopump was operated stably, satisfying the performance requirements. Head coefficient and flow coefficient of the pumps remained constant at the speed-increasing period. In terms of performance characteristics of pumps and turbine, the results from the turbopump assembly test showed a good agreement with those from the turbopump component tests.