• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.54-61
• /
• 1998

A numerical simulation is attempted for the regenerative cooling heat transfer processes of the liquid propellant rocket engine. The heat transfer from the combustion gases to the thrust chamber wall is called gas side heat transfer. This heat is conducted radially to the coolant through the carbon deposit and metallic wall of thrust chamber Finally, this heat is convected away by the coolant flowing along the passages in the thrust chamber. The equivalence of these three heat fluxes of the above processes is utilized to determine the coolant side wall temperature, gas side wall temperature and the heat flux. When the number and shape(width, height) of coolant passages, the shape(size) of thrust chamber, oxidant and fuel properties, coolant properties, oxidant/fuel mixture ratio, coolant inlet temperature, the thickness of carbon deposit formed along the thrust chamber wall during combustion are given, reasonable radial direction temperature distributions and heat fluxes along the thrust chamber axis are obtained.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.110-118
• /
• 2021

In a liquid rocket engine system, the flow of oxidizer into the combustion chamber is controlled by the main oxidizer shut-off valve. When the valve is closed, the oxidizer flows via the recirculation line, not into the combustion chamber. In this situation, the measured pressure could be much higher than a design value because of the water hammer phenomenon. In this paper, the experiments on the water hammer in the recirculation line with different initial conditions were conducted in order to study the pressure wave produced in each case. According to the experimental results, characteristics of the pressure wave in the recirculation line depend on the initial condition. To be specific, the pressure surge is maximized in case that the shock is condensation-oriented in the end of the recirculation line.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.4
• /
• pp.40-46
• /
• 2006

A 30-tonf-class fullscale thrust chamber for the application to a Low-Earth-Orbit Space Launch Vehicle has been combustion tested over the wide ranges of a mixture ratio and a chamber pressure. The thrust chamber designed for a pump-fed open cycle engine was tested with an ablative chamber instead of a regenerative one for the initial evaluation of its performance and function. The test results revealed stable combustion characteristics. The hardware survived the harsh environment and showed very sound functional characteristics. The measured combustion efficiency turned out to be 95% and a specific impulse at sea level was estimated as 254sec, which are comparable to or above the predetermined design values.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.198-204
• /
• 2004

Using liquefied natural gas as a fuel, water, natural gas and liquefied natural gas-cooled firing tests were conducted. With the viewpoint of characteristic velocity, and specific impulse, the effect of OF mixture ratio and fuel inlet temperature into a combustion chamber were analyzed. OF mixture ratio and fuel inlet temperature into a combustion chamber have great influence on the performance. Characteristic velocity and theoretical specific impulse attain the maximum value at 0.72~0.75 and 0.75 of OF mixture ratio, respectively. Engine performance has a tendency to increase, proportional to fuel inlet temperature into a combustion chamber affected by the regenerative cooling.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.2
• /
• pp.60-71
• /
• 2022

The reusable, low-cost launch vehicle development trend in the recent launch vehicle market is being subdivided into several ways, and the throttleable engine is one of them. Plus, several nations have selected methane as a next-generation propellant due to its cleanness. In this research, a throttleable pintle injector using gas methane and liquid oxygen as propellants was developed, followed by its spray and combustion characteristics analysis, including high pressure cold and hot tests. The designed throttleable pintle injector has a double sleeve structure, and its tightness and functionality are confirmed through repetitive atmospheric, high-pressure cold tests, and hot tests. Though some design errors were discovered and a low throttling level was unable to be achieved in the combustion test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.6 no.4
• /
• pp.37-45
• /
• 2002

The development process of KSR-III propulsion feeding system is subscripted. The purpose of propulsion feeding system is to feed a certain amount of propellant from propellant tank to engine by the end of combustion. Pressure-fed liquid rocket, KSR-III has the unique characteristics of both pressure regulator and cavitation venturi as a passive flow control device. Main parameters of feeding system are confirmed by both water test and CFD(전산유체) technique. Flow control effect with venturi is confirmed by water test. Initial stabilization characteristic of pressure regulator is confirmed by real propellant test. And, to avoid the effect of resonance between rocket and feeding system, this article deal with POGO(포고) analysis to the feeding system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.3
• /
• pp.90-98
• /
• 1998

The vaporization process of liquid oxygen(LOX) at high pressure environment is numerically investigated. The present vaporization model can account for the high-pressure effects such as ambient gas solubility, real gas behavior and variable properties. The predicted phase-equilibrium compositions for $N_2$/$H_2$ and $O_2$/He system are well agreed with experimental data. The LOX vaporization characteristics is parametrically studied for wide range of the operating conditions encountered in the high-pressure combustion process of liquid rocket engine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.207-210
• /
• 2005

The results of combustion performance test of fuel-rich gas generator with dual swirl injectors are described. By changing simulating duct and recess number(RN) of the injectors, we inspected whether the combustion instability took place. When the injectors of RN = 0.5 were used, combustion instabilities could be reduced using the simulating duct. However, the effect of the simulating duct on the gas generator with the injectors of RN = 1.5 was not significant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.175-178
• /
• 2006

A numerical study for spray combustion of fluctuated fuel and oxidizer droplets injected into combustion chamber has been conducted for the analysis of spray combustion considering characteristics of injector. The 2 dimensional unsteady state flow fields have been calculated by using QUICK Scheme and SIMPLER Algorithm. As the spray model, DSF model and Euler-Lagrange Scheme have been used. The sine Auction has been used for droplet fluctuation model of fuel and oxidizer, while the coupling effects of the droplets between gas phase and evaporated vapor have been calculated by using PSIC model.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.119-122
• /
• 2007

The present study employs experimental approach to identify combustion stability characteristics of fuel-rich gas generators. The gas generator of interest, fueled by LOx and Jet A-1, experienced combustion instability coupled to a longitudinal resonant mode of the combustion chamber at about 1200 Hz. The occurrence of instability is strongly associated with acoustic boundary condition at the exit .and axial location of maximum heat release. As a result, stretching heat release zone in the axial direction by increase of the fuel nozzle diameter has dramatically stabilized combustion.