• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.2
• /
• pp.92-97
• /
• 2005

A series of combustion test was done to verify the optimization result of a gas generator for a 10 ton thrust liquid rocket engine. An injector element is F-O-F impinging type injector and the test was conducted with kerosene/LOX propellants. Test results of combustion temperature and pressure show a very good agreement with optimal design result and verify that the design method was properly established. And turbulence ring revealed its effectiveness in enhancing combustion gas mixing and temperature difference in the radial direction showed only less than 15K. Also turbulence ring induced only 3.2% pressure loss in the combustion chamber, which is far less than conventional level observed in a gas turbine engine. Axial temperature distribution also shows that turbulence ring could effectively reduce about 10% or more in gas generator length if its location is properly selected.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.9 no.4
• /
• pp.48-54
• /
• 2005

An experimental study was carried out to investigate the effect of film cooling in the lab-scale liquid rocket engine using liquid oxygen(LOx) and Jet A-1(Jet engine fuel) as propellants. Film coolants(Jet A-1 and water) was injected through the film cooling injector. The outside wall temperature of the combustor and film cooled length were determined for chamber pressure, mixture ratio, and the different geometries(injection angle) with the percent film coolant flow rate. The loss of characteristic velocity was determined for the case of film cooling with water and Jet A-1. As chamber pressure increased, the outside wall temperature increased in the nozzle but unchanged over the 9 percent film coolant flow rate for the combustion chamber used in this study. Characteristic velocity wasn't affected with the mixture ratio over the 9 percent film coolant flow rate.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.82-85
• /
• 2009

In the development of Liquid Rocket Engine(LRE) systems, it is essential to understand the spray characteristics which influence mainly the performance and the stability of combustion. The injectors for this study have a recessed Liquid-swirl/Gas-centered jet coaxial type. For the similarity with actual conditions, the experimental conditions are calculated by using the momentum ratio as a matching parameter, and the stimulants of fuel and oxidizer are gaseous nitrogen and water respectively. The spray fields were measured by means of a photographic technique. Moreover, an effect of the momentum ratio has been investigated.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.61-64
• /
• 2009

A study on the variation of combustion performance by oxidizer/fuel ratio was conducted. Shower head type injector was used. Injector propelled by liquid kerosene and liquid hydrogen peroxide. The designed operation condition for thrust and combustion pressure were 200N and 10bar. It is found that optimum oxidizer/fuel ratio.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.141-144
• /
• 2003

For the analysis of combustion instabilities of a liquid locket engine, a simple spray combustion model has been analyzed by the Euler-Lagrange method. Gas temperature, droplet trajectory, and droplet radius have been evaluated on 2-D axisymmetric coordinates. The Euler-Lagrange method has been shown to have a good tendency of gas temperature distribution as well as droplet trajectory and radius change.

• Journal of computational fluids engineering
• /
• v.8 no.3
• /
• pp.56-65
• /
• 2003

A numerical procedure for analyzing the heat transfer in a regenerative cooling passage of liquid rocket has been developed. The thermal analysis is based on the numerical model of Naraghi〔1〕. The thermodynamic and transport properties of the combustion gases are evaluated using the chemical equilibrium composition. The pressure and heat flux obtained by the isentropic relation are in good agreement with the result of Navier-Stokes equations. The effect of design parameters on heat transfer is addressed for the pressure loss and temperature variation. Also, their constraints in designing the cooling passage are recommended. Finally, in a heated rectangular duct, the effects of secondary flow on heat transfer are scrutinized by the nonlinear k- e -fu of Park et at.〔2〕.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.6
• /
• pp.79-87
• /
• 2003

Application of combustion stabilization devices such as baffle and acoustic cavity to liquid propellant rocket engine is investigated to suppress high-frequency combustion instability, i.e., acoustic instability. First, these damping devices are designed based on linear damping theory. As a principal design parameter， damping factor is considered and calculated numerically in the chambers with/without these devices. Next, the unbaffled chambers with/without acoustic cavities are tested experimentally for several operating conditions. The unbaffled chamber shows the peculiar stability characteristics depending on the operating condition and it is found to have small dynamic stability margin. As a result, the acoustic cavity with the present design has little stabilization effect in this specific chamber. Finally， stability rating tests are conducted with the baffled chamber, where evident combustion stabilization is observed, which indicates sufficient damping effect.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.118-122
• /
• 2006

For the development of a gas generator of a liquid rocket engine, the prediction of thermodynamic properties of combustion gas with respect to a propellant mixture ratio becomes critical. The present study focuses on the temperature measurement of exit combustion gas as a function of a mixture ratio through combustion tests of a fuel-rich gas generator propelled by Lox/Jet A-1. The measurement of combustion dynamic and static pressures allowed indirect estimation of thermodynamic properties like specific heat ratio, gas constant, and constant pressure specific heat. Comparing the results with empirical prediction through an interpolation reveals that the interpolation method calibrated using temperature results can be utilized as an effective tool for the design of a fuel-rich gas generator.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.258-261
• /
• 2003

The optimal design and combustion analysis of the gas generator for Liquid Rocket Engine (LRE) were performed. A fuel-rich gas generator in open cycle turbopump system was designed for 101on1 in thrust with RP-1/LOx combination. The optimal design was done for maximizing specific impulse of main combustion chamber with constraints of combustion temperature and power matching in turbopump system. Results of optimal design show the dimension of length, diameter, and contraction ratio of gas generator. The configuration of the gas generator and the condition for performance which can maximize the objective function were determined and found to meet the design constraints. Also, the combustion analysis was conducted to evaluate the performance of designed chamber and injector of gas generator. And the effect of the turbulence ring was investigated on the mixing enhancement in the chamber.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.91-96
• /
• 2004

An optimal design of the gas generator for Liquid Rocket Engine (LRE) was conducted. A fuel-rich gas generator in open cycle turbopump system was designed for 10ton in thrust with RP-1/LOx propellant. The optimal design was done for maximizing specific impulse of thrust chamber with constraints of combustion temperature and for matching the power requirement of turbopump system. Design variables are total mass flow rate to gas generator, O/F ratio in gas generator, turbine injection angle, partial admission ratio, and turbine rotational speed. Results of optimal design provide length, diameter, and contraction ratio of gas generator. And the operational condition predicted by design code with resulting configuration was found to maximize the objective function and to meet the design constraints. The results of optimal design will be tested and verified with combustion experiments.