• Journal of the Korean Wood Science and Technology
• /
• 제26권4호
• /
• pp.92-97
• /
• 1998

Four urea-formaldehyde (UF) resins were synthesized as a particleboard (PB) binder with the four different initial formaldehyde/urea mole ratio and the final mole ratio of 1.15. The UF resins were characterized according to the standard method of resin adhesive analysis. PBs were manufactured using liquid UF resins at 5 minutes press time and 6% resin solids levels on an ovendry particle weight basis. A total of 20 PBs was fabricated for 5 panel replication per UF resin types. The panels were tested for physical strength properties per the procedure ASTM D 1037. The formaldehyde emission levels from the PBs bonded with the UF resins were tested according to 2-hour desiccator test method ASTM D 5582. There were no significant differences among UF resin types for internal bond strength of PBs. But there were significant differences among UF resin types for formaldehyde emission level of PBs. The results showed that the formaldehyde emission level was influenced by the UF resin types without reducing the adhesive performance.

• 전기화학회지
• /
• 제16권1호
• /
• pp.30-38
• /
• 2013

In this study, a catalyst slurry was prepared with a Pt/C catalyst, Nafion ionomer solution as a binder, an ionic liquid (IL) (1-butyl-3-methylimidazolium tetrafluoroborate), deionized water and ethanol as a solvent for the application to polymer electrolyte fuel cells (PEFCs) at high-temperatures. The effect of the IL in the electrode of each design was investigated by performing a cyclic voltammetry (CV) measurement. Electrodes with different IL distributions inside and on the surface of the catalyst electrode were examined. During the CV test, the electrochemical surface area (ESA) obtained for the Pt/C electrode without ILs gradually decreased owing to three mechanisms: Pt dissolution/redeposition, carbon corrosion, and place exchange. As the IL content increased in the electrode, an ESA decrement was observed because ILs leaked from the Nafion polymer in the electrode. In addition, the CVs under conditions simulating leakage of ILs from the electrode and electrolyte were evaluated. When the ILs leaked from the electrode, minor significant changes in the CV were observed. On the other hand, when the leakage of ILs originated from the electrolyte, the CVs showed different features. It was also observed that the ESA decreased significantly. Thus, leakage of ILs from the polymer electrolyte caused a performance loss for the PEFCs by reducing the ESA. As a result, greater entrapment stability of ILs in the polymer matrix is needed to improve electrode performance.

• Computers and Concrete
• /
• 제14권5호
• /
• pp.577-597
• /
• 2014

This paper aims to develop a prediction model for the hardened properties of waste LCD glass that is used in concrete by analyzing a series of laboratory test results, which were obtained in our previous study. We also summarized the testing results of the hardened properties of a variety of waste LCD glass concretes and discussed the effect of factors such as the water-binder ratio (w/b), waste glass content (G) and age (t) on the concrete compressive strength, flexural strength and ultrasonic pulse velocity. This study also applied a hyperbolic function, an exponential function and a power function in a non-linear regression analysis of multiple variables and established the prediction model that could consider the effect of the water-binder ratio (w/b), waste glass content (G) and age (t) on the concrete compressive strength, flexural strength and ultrasonic pulse velocity. Compared with the testing results, the statistical analysis shows that the coefficient of determination $R^2$ and the mean absolute percentage error (MAPE) were 0.93-0.96 and 5.4-8.4% for the compressive strength, 0.83-0.89 and 8.9-12.2% for the flexural strength and 0.87-0.89 and 1.8-2.2% for the ultrasonic pulse velocity, respectively. The proposed models are highly accurate in predicting the compressive strength, flexural strength and ultrasonic pulse velocity of waste LCD glass concrete. However, with other ranges of mixture parameters, the predicted models must be further studied.

• Advances in materials Research
• /
• 제9권3호
• /
• pp.219-231
• /
• 2020

The aim of this study is to investigate the durability of fly ash based geopolymer mortar with and without protective coatings in aggressive chemical environments. The source materials for geopolymer are Fly ash and Ground Granulated Blast furnace Slag (GGBS) and they are considered in the combination of 80% & 20% respectively. Two Molarities of NaOH solution were considered such as 8M and 10M. The ratio of binder to sand and Sodium silicate to Sodium hydroxide solution (Na₂SiO₃/NaOH) are taken as 1:2 and 2 respectively. The alkaline liquid to binder ratio is 0.4. Compressive strength tests were conducted at various ages of the mortar specimens. In order to evaluate the performance of coatings on geopolymer mortar under aggressive chemical environment, the mortar specimens were coated with two different types of coatings such as epoxy and Acrylic. They were then subjected to different chemical environments by immersing them in 10% standard solutions of each ammonium nitrate, sodium chloride and sulphuric acid. Drop in compressive strength as a result of chemical exposure was considered as a measure of chemical attack and the drop in compressive strength was measured after 30 and 60 days of chemical exposure. The compressive strength results following chemical exposure indicated that the specimens containing the acrylic coating proved to be more resistant to chemical attacks. The control specimen without coating showed a much greater degree of deterioration. Therefore, the application of acrylic coating was invariably much more effective in improving the compressive strength as well as the resistance of mortar against chemical attacks. The results also indicated that among all the aggressive attacks, the sulphate environment has the most adverse effect in terms of lowering the strength.

• 한국산학기술학회논문지
• /
• 제16권10호
• /
• pp.6816-6822
• /
• 2015

본 연구에서는 기존의 글라스울의 흡습에 의한 변형을 해결하고 단열성능향상을 위해 실리카 에어로젤을 이용한 단열재를 개발하였다. 글라스울 단열재에 액상의 혼합 바인더를 이용하여 실리카에어로젤이 함침된 글라스울 복합체를 제조하였다. 액상의 혼합 바인더는 수용성바인더(CMC, carboxymethyl cellulose)와 물에 분산시킨 실리카 에어로젤을 이용하여 준비하였다. 초기 $0.048g/cm^3$의 밀도를 갖는 글라스울 보드를 준비하고 실리카 에어로젤을 함침시켜 $0.065g/cm^3$의 밀도를 갖는 단열보드를 제작할 수 있었다. 이렇게 제조된 실리카 에어로젤 함침 글라스울 보드 복합체는 단일 글라스울 보드의 단열성능보다 7.4% 향상된 0.0315 W/mK의 열전도율(thermal conductivity)을 나타내었다. 제조된 실리카 에어로젤-글라스울 복합체는 불꽃 관통시험에서 362초간 내화 저항성을 나타내어 단일 글라스울 보드에 비하여 2.7배나 높은 내화성능을 보였다. 또한 일반 글라스울 보드는 흡습에 의하여 수직방향으로 처짐현상을 나타내는 단점이 있었으나, 실리카 에어로젤이 함침된 보드에서는 실리카 에어로젤의 발수특성으로 인하여 높은 내수성능을 나타내는 것을 확인하였다.

• 공업화학
• /
• 제32권2호
• /
• pp.174-179
• /
• 2021

인조흑연 제조용 바인더로 주로 이용되는 콜타르 핏치와 페놀 레진은 soft carbon 및 hard carbon의 초기 탄소화합물 구조에 차이가 있다. 따라서 탄화 온도에 따른 열분해 거동, 미세조직, 결정성의 변화 과정도 다를 것으로 예상할 수 있다. 본 연구에서는 콜타르 핏치 및 페놀 레진의 열분해 거동, 미세조직, 결정성 변화에 관하여 비교 분석하였다. 콜타르 핏치는 액상을 경유한 탄화 과정을 거치며, 탄화 온도가 증가함에 따라 미세조직이 점차 변화되는 것을 확인할 수 있었다. 탄화 온도가 증가함에 따라 콜타르 핏치 및 페놀 레진 모두 결정성은 증가하는 경향을 나타냈지만, 콜타르 핏치는 미세조직이 급변하는 500 및 600 ℃ 구간에서 결정성도 급격히 변화는 것을 확인할 수 있었다. 또한 미세조직과 결정성은 서로 밀접한 연관성이 있었다.

• 농약과학회지
• /
• 제2권3호
• /
• pp.36-44
• /
• 1998

각기 다른 종류의 입상담체(extruded pellets, sands, zeolites)를 이용하여 보조제의 종류와 조성을 달리하고 주성분을 피복 또는 흡착시켜 제제한 제제품과 조립흡착식으로 제조된 butachlor + chlometholefen(3.5 + 7.0%, 부로트 입제) 혼합입제의 부유성, 수중확산 또는 붕괴성, 수중용출도 및 생물효과를 비교하여 우수한 물성 및 효과를 갖는 용출제어형 입제 제조법을 개발하고자 하였다. 물성이 다른 원제를 이용하여 입제를 제조하기 위해서 여러 제조방식을 이용하는데 원제 2개 이상 혼합된 입제를 제조하기 위해서 고상인 원제와 증량제 및 보조제를 첨가시켜 조립한 뒤 여기에 액상 원제를 흡착시켜 제조한 입제는 우수한 부유성과 수중붕괴성, 안정된 수중용출도를 나타내었으며, 생물효과도 안정적으로 발휘시킬 수 있었다. 기립입자를 담체로 이용하여 피복 또는 흡착시킨 기립피복식 입제들은 부유성, 수중붕괴성 및 생물효과면에서 기존 입제와 대등하거나 우수하였지만 불안정한 수중용출 경향을 나타내었다. 그러나 모래피복형의 경우 기립피복식이나 지오라이트피복식과 달리 액상의 binder가 비교적 안정적으로 주성분들의 수중용출에 도움을 주었고 분상의 dispersing agent보다 액상이 부유성, 수중붕괴성 및 생물효과 면에서 기존과 비슷했거나 좋았던 결과로 볼 때 적절한 binder와 액상의 dispersing agent를 선택하여 제조한다면 기존 조립흡착식 입제와 대등하거나 우수한 물성 및 생물효과를 발현하는 입제를 개발할 수 있는 제조방식인 것으로 판단되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 춘계학술대회 및 기술 세미나 논문집 디스플레이 광소자
• /
• pp.42-42
• /
• 2008

Considerable attention has been focused on the applications of flexible liquid crystal (LC)-based displays because of their many potential advantages, such as portability, durability, light weight, thin packaging, flexibility, and low power consumption. To develop flexible LCDs that are capable of delivering high-quality moving images, like conventional glass-substrate LCDs, the LC device structure must have a stable alignment layer of LC molecules, concurrently support uniform cell gaps, and tightly bind two flexible substrates under external tension. However, stable LC molecular alignment has not been achieved because of the layerless LC alignment, and consequently high-quality images cannot be guaranteed. To solve these critical problems, we have proposed a PDMS pixel-wall based bonding method via the IB irradiation was developed for fasten the two substrates together strongly and maintain uniform cell gaps. The effect of the IB irradiation on PDMS with PI surface was also evaluated by side structure configuration and a result of x-ray photoelectron spectroscopic analysis of PDMS interlayer as a function of binder with substrates. large number of PDMS pixel-walls are tightly fastened to the surface of each flexible substrate and could maintain a constant cell gap between the LC molecules without using any other epoxy or polymer. To enhance the electro-optical performance of the LC device, we applied an alignment method that creates pretilt angle on the PI surface via ion beam irradiation. Using this approach, our flexible LCDs have a contrast ratio of 132:1 and a response time of about 15 ms, resulting in highly reliable electro-optical performance in the bent state, comparable to that of glass-substrate LCDs.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1704-1706
• /
• 1999

$YBa_2Cu_3O_x$ superconducting thick film was fabricated by surface diffusion process of $Y_2BaCUO_5$ and the mixed compound of $(3BaCuO_2+2CuO)$ expected to be liquid phase above the peritectic temperature of YBa2Cu30x. For the surface diffusion. 3BaCu02+2CuO mixed with binder material was patterned on $Y_2BaCuO_5$ substrate by the screen printing method. The characteristic of current limit on thick film fabricated was measured. The thick film limited the current from $2.8213mA_{rms}$ to $4.2034mA_{rms}$ with $500{\Omega}$ load resistance, and from $4.1831mA{rms}$ to $4.2150mA_{rms}$ with $10{\Omega}$ load resistance.

• 한국세라믹학회지
• /
• 제46권3호
• /
• pp.288-294
• /
• 2009

The platelet AlO(OH) nano colloids were prepared by hydrothermal reaction of the $\gamma-Al_2O_3$ obtained with dehydration of $\gamma$-AlO(OH) and dilute $CH_3COOH$ solution. In hydrothermal reaction process, reversible reaction was accompanied between $\gamma-Al_2O_3$ and AlO(OH), and hydrothermal reaction temperature, hydrothermal reaction time and $CH_3COOH$ concentration had an effect on the crystal structure, surface chemical property, surface area, pore characteristics and crystal morphology of the AlO(OH) nano colloid particles. In this study, it was investigated to the hydrothermal reaction condition of the AlO(OH) nano colloid for using catalyst support, heat resisting agent, adsorbents, binder, polishing agent and coating agent. The crystal structure, surface area, pore volume and pore size of the platelet AlO(OH) nano colloids were investigated by XRD, TEM, TG/DTA, FT-IR and $N_2$ BET method in liquid nitrogen temperature.