• 한국세라믹학회지
• /
• 제17권2호
• /
• pp.69-74
• /
• 1980

This study deals with the wire content, wire diameter, aspect ratio , it's arrangement of steel, wire fiber and the sorts of castable which affected the character of steel wire fiber reinformced refractory castable. Two kinds of alumina based refractory castables, one is for 1650℃ and the other is for 1800℃, and stainless steel which is SUS 304 type 0.25, 0.34 , 0.37 and 0.50m/min diameter were used respectively. Aspect ratio was adjusted to 50, 75, 100 and steel fiber content was also adjusted to 1-4wt% each. The results of the experiment were as follows : 1. At firing temperature around 1,000℃, MOR is increased with increasing wire content and aspect ratio with decreasing firing temperature, which depends on the Romualdi's Fiber Spacing Theory. But for calculation of the fiber spacing, Swamy equation is more a aplicable to the extensive fiber mixing conditions. However, the condition differs from the above at firing temperature around 1,350℃ ,because of the degradation of wire and the progress of sintering of castable. 2. Linear change is getting larger corresponding to the increase of wire content, and the spaling resistivity is increasing corresponding to the increase of wire content and to aspect ratio, and with decreasing wire diameter. 3. Firing shrinkage under load is getting greater as higher wire content, and the shrinkage of the test pieces which fiber is vertically oriented is getting greater than the test pieces which fiber is randomly oriented.

• 한국세라믹학회지
• /
• 제34권5호
• /
• pp.519-527
• /
• 1997

The effect of Al content and heating rate on the sintering behavior, microstructure, and mechanical properties of reaction bonded alumina (RBAO) was investigated. As the heating rate became slower a critical Al content which could be added to RBAO increased. The weight gain and linear shrinkage of RBAO containing of 55 vol% Al were 28% and 6.5%, respectively. The relative density of RBAO decreased from 96 to 94%, as the amount of Al increased from 15 to 55 vol%. The hardness of RBAO increased from 17.8 to 19.9 GPa and the bending strength enhanced from 370 to 570 MPa, as the amount of Al increased from 15 to 55 vol%. On the other hand, the wear rate of RBAO degraded from 6.7 to 3.39$\times$10-5 $\textrm{mm}^2$/kg and the fracture toughness decreased from 4.1 to 3.6 MPa.m1/2, as the amount of Al increased from 15 to 55 vol%. Fracture modes were shown to the mixed mode of inter/transgranular. However, transgranular fracture was dominant with increasing the content of Al.

• 한국세라믹학회지
• /
• 제27권7호
• /
• pp.899-906
• /
• 1990

The cordierite powders were prepared from Mg(NO3)2.6H2O, Al(NO3)3.9H2O and colloidal silica by the coprecippitation method, and the sintering behavior of the powders were investigated. Two different methods were applied for producing the precursor powders. The one was to added the aqueous solution of Mg(NO3)2.6H2O and Al(NO3)3.9H2O to NH4OH to adjust pH at 10 where the colloidal silica of pH 10 was added. The other wa to add the aqueous solution of Mg(NO3)2.6H2O and Al(NO3)3.9H2O to the colloidal silica with NH4OH to control the final mixture to be at pH 10. It was confirmed that more homogeneous powders were obtained from the latter method. The firing linear shrinkage of the powder compacts fabricated from the calcined powder between 90$0^{\circ}C$ and 110$0^{\circ}C$ was found to be larger as the calcination temperature was low. But all of them stopped shrinking around 120$0^{\circ}C$. The powder compacts, fabricated using the calcined powders at 90$0^{\circ}C$ and 95$0^{\circ}C$ for 2hours and sintered at 142$0^{\circ}C$ for 2hours, showed relative density of 93-96%, 3-point bending strength of 81-83MPa, KIC of 1.9-2.4 MPam1/2 and thermal expansion coefficient of 0.213-0.732$\times$10-6$^{\circ}C$.

• 한국세라믹학회지
• /
• 제29권2호
• /
• pp.101-106
• /
• 1992

Sintering behavior, distribution of dopant oxides and electrical properties in the ZnO-Bi2O3-CoO-Sb2O3 and ZnO-Bi2O3-CoO-Sb2O3-Cr2O3 systems were studied. The linear shrinkage of ZnO varistors from 850 to 950$^{\circ}C$ was related to the decomposition reaction (py\longrightarrowsp+Bi2O3) of the pyrochlore phase. In the distribution of the dopant oxides (CoO, Sb2O3, Cr2O3), Co distribute uniformly throughout the sample, the distribution of Sb coincided with small particles (spinel phase, Zn7Sb2O12), and Cr distributed very consistently with Sb. The increase in breakdown voltage, due to the addition of Cr2O3, was not only attributed to the decrease in the ZnO grain size but also to the solution of Cr2O3 in the spinel phase. The leakage current (80% V60 ${\mu}\textrm{A}$) was increased by the addition of Cr2O3.

• 한국세라믹학회지
• /
• 제20권4호
• /
• pp.347-355
• /
• 1983

A batch mixture was prepared as 16mol% CaO-84mol% $ZrO_2$ of regeant-grade powder. The monoclinic Zirconia powder had an average particle size of $9.24 \mu\textrm{m}$ and calcium carbonate powder had a reported purity of 99.7 weight percent and mean particle size of TEX>$24, 37<\mu\textrm{m}$. The specimens were fired at 1400, 1500, 1650 and $1750^{\circ}C$ for 0. 3, 5 and 7 hours respectively. After fired the specimens were investigated using Scaning electron microscopy. Density Porosity Compressive strength Modulus of rupture and Thermal expansion were measured X-ray diffration analysis was also carried out. The results are as follows ; 1) As the firing temperature or soaking time was increased firing linear shrinkage apparent density compressive strength and modulus of rupture increased but apparent porosity decreased, 2) Cubic and monoclinic Zirconia was found at $1400^{\circ}C$ and cubic Ziconia found above $1500^{\circ}C$ 3) The specimens fired at 140$0^{\circ}C$ without soaking display thermal expansion curves by monoclinic〓tetragonal transformation and no tranformation was found at $1400^{\circ}C$ for 5hrs and above $1500^{\circ}C$. 4) The lattice parameter had constant value of 5.1345 $\AA$ through all the ranges of firing temperature 5) The higher the firing temperature was or the longer the soaking time was the larger the grain size was.

• 한국전기전자재료학회논문지
• /
• 제34권5호
• /
• pp.342-347
• /
• 2021

Phase evolution, sintering behavior, microstructure, and microwave dielectric properties of (1-x) mol Ba₃V₄O₁₃ - (x) mol BaV₂O₆ system were investigated. The sintered specimens of all compositions consisted of Ba₃V₄O₁₃ and BaV₂O₆, and no secondary phase was observed. As x increased, the linear shrinkage decreased to the composition of x=0.5, and then increased again, implying that Ba₃V₄O₁₃ and BaV₂O₆ phases interfered mutually with each other during sintering. All compositions showed a dense microstructure with a large grain growth. Cracks were observed in some compositions because of the relatively high sintering temperature of 620~640℃. As x increased, the dielectric constant increased, while the quality factor was maintained from about 50,000 GHz to about 70,000 GHz up to the composition of x=0.9, and then decreased to 20,987~27,180 GHz at the composition of x=1.0. As x increased, the temperature coefficient of the resonance frequency showed a (+) value from a (-) value. The dielectric constant, the quality factor, and the temperature coefficient of resonant frequency of x=0.7 composition sintered at 640℃ for 4 hours were 10.61, 71,126 GHz, and -4.9 ppm/℃, respectively. This composition showed a good chemical compatibility with Al powder, indicating that the Ba₃V₄O₁₃-BaV₂O₆ ceramics are a candidate material for ULTCC (Ultra-Low Temperature Co-fired Ceramics) applications.

• 대한치과보철학회지
• /
• 제48권2호
• /
• pp.143-150
• /
• 2010

연구목적: 본 연구의 목적은 냉간 정수압 성형법 (cold isostatic press forming)을 이용한 새로운 지르코니아 블록의 제조와 이를 이용한 코어와 완전 도재관의 적합도를 비교 평가하여 임상적 이용 가능성을 평가 하고자 함이다. 연구 재료 및 방법:지르코니아 분말 (KZ-3YE Type A)을 단일 압축 성형하여 블록의 형태로 제작 한 후, 냉간 정수압 성형하여 블록을 제작하고, 성형이 끝난 지르코니아 블록은 $1040^{\circ}C$의 온도에서 반 소결하였다. 대조군은 상용 제품 ($Everest^{(R)}$, KAVO, Biberach/$Ri{\beta}$.)을 이용하였다. $1450{^{\circ}C}$의 온도에서 완전 소결된 실험군 블록과 대조군 블록의 수축률을 측정하고 비교하였다. CAD/CAM을 이용하여 총 21개의 코어를 제작하고 세 그룹으로 나누었다. Group I은 대조군 블록을 이용해 7개의 코어를 제작하고, Group II는 실험군 블록을 이용해 7개의 코어를 제작하였다. Group III은 실험군 블록을 이용해 7개의 코어를 제작하고 도재 ($Cerabien^{TM}$)를 축성하여 완전 도재관을 제작하였다. 제작된 코어와 완전 도재관을 모형에 합착한 후 레진으로 매몰하여 치관 장축의 협설과 근원심 방향을 따라 절단하고 지대치와 코어 사이의 변연 간격과 내부 축면 간격 그리고 내부 교합면 간격을 SEM ($S-4700^{(R)}$)을 이용해 측정하였다. 모든 측정값은 평균과 표준편차를 계산하고, one-way ANOVA test를 시행하여 실험 결과를 분석하였고, 95%유의 수준으로 검정하였다. 결과:실험군과 대조군 블록의 수축률을 측정한 결과 실험군 블록의 수축률은 19.00%였고, 대조군 블록의 수축률은 20.09%로 실험군 블록의 수축률이 더 낮은 것으로 나타났다. 적합도 측정 결과 변연 간격의 측정값에서 Group II의값($29.67{\pm}6.58 {\mu}m$)이 Group I의값($36.84 {\pm}7.18 {\mu}m$)보다 통계적으로 유의하게 작은 것으로 나타났다. 또한 Group II와 Group III의 값 사이에서는 유의한 차이가 없었다. 내부 측면 간격의 측정값에서 Group III의값($32.23{\pm}6.33 {\mu}m$)이 Group I와 Group II의내부측면간격의값($37.57{\pm}6.81{\mu}m$, $38.14{\pm}6.81{\mu}m$)보다 큰 것으로 나타났다. 각 부위의 간격 측정결과 내부 교합면 간격의 값이 변연 간격 및 내부 축면 간격의 값보다 유의하게 큰 것으로 나타났다. 결론: 현재 상용중인 대조군 블록과 비교하여 냉간 정수압 성형법으로 제조된 실험군 블록의 적합도는 유의한 차이를 보이지 않았다. 변연 적합도는 실험군에서 더 우수하였으며 도재를 축성한 완전 도재관의 적합성이 약간 더 향상되는 경향을 보였다. 변연 적합도는 대조군과 실험군 모두에서 임상적으로 허용되는 양호한 수치를 보였다.