• 한국항공우주학회지
• /
• 제34권9호
• /
• pp.76-81
• /
• 2006

본 논문에서는 공기흡입식 추진기관용 연료공급 시스템의 연료조절 밸브 시스템을 제안하였으며, 제안된 시스템은 서보밸브에 의해 구동되는 차압유지 밸브와 미터링 밸브로 구성되어 있다. 시스템 성능 및 안정성에 영향을 미치는 인자를 찾기 위해 비선형 및 선형 해석을 수행하였다. 이를 통해 미터링 밸브 오리피스 양단의 차압 유지량 ${\Delta}P$가 시스템 안정성에 영향을 미침을 예측하였고 실험 및 비선형 전산모사를 통하여 입증하였다. 해석 및 실험 결과차압 유지량 ${\Delta}P$를 줄이고 동시에 이등변 삼각형 형상의 오리피스를 차압유지 밸브에 적용함으로써 요구 유량에 따라 유량이득이 조절되도록 하여 시스템의 안정성을 높일 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.486-493
• /
• 2000

Flow mechanism around air flow sensor of electronic control engine, especially Karman vortex type, was investigated experimentally. The two-dimensional flow characteristics in the intermediate wake region behind a triangular vortex-generator respectively apex forward facing, apex backward facing and vertical flat plates following after apex forward facing(i.e vortex-flowmeter) were investigated at Reynolods number of $ReH=1.4\times10^4$; H is the width of a triangular vortex-generator. The vortex shedding frequency for wide Reynolds number from $7\times10^3$ to $2.1\times10^4$ was also surveyed. The velocity component was measured by X-type hot wire anemometer at 8H downstream from the bluff body. The coherent structure of the intermediate wake behind a bluff body was obtained by conditional phase average technique. As a result, it was verified that the vertical flat plates following after apex forward triangular vortex-generator make not only more linear relation between free stream velocity and vortex shedding frequency but also more periodic vortex in the vicinity of the center of wake.

• 한국자동차공학회논문집
• /
• 제23권1호
• /
• pp.56-64
• /
• 2015

This study presents a model-based gain scheduling strategy for PI-based EGR controllers. The air-to-fuel ratio is used as an indirect measurement of the EGR rate. In order to cope with the nonlinearity and parameter varying characteristics of the EGR system, we proposed a static gain model of the EGR system using a new scheduling parameter. With the 810 steady-state measurements, the static gain model achieved 0.94 of R-squared value. Based on the static gain of the EGR system, the PI gains were robustly designed using quantitative feedback theory. Consequently, the gains of the PI controller are scheduled according to the static gain parameter of the EGR path in runtime. The proposed model-based gain scheduling strategy was validated through various operating conditions of engine experiments such as setpoint step responses and disturbance rejections.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.690-693
• /
• 2002

According to the growth of communication biz, embedded market rapidly developing in domestic and overseas. Embedded system can be used in various way such as wire and wireless communication equipment or information products. There are lots of developing performance applying speech recognition to embedded system, for instance, PDA, PCS, CDMA-2000 or IMT-2000. This study implement minimum memory of speech recognition engine and DB for apply real time embedded system. The implement measure of speech recognition equipment to fit on embedded system is like following. At first, DC element is removed from Input voice and then a compensation of high frequency was achieved by pre-emphasis with coefficients value, 0.97 and constitute division data as same size as 256 sample by lapped shift method. Through by Levinson - Durbin Algorithm, these data can get linear predictive coefficient and again, using Cepstrum - Transformer attain feature vectors. During HMM training, We used Baum-Welch reestimation Algorithm for each words training and can get the recognition result from executed likelihood method on each words. The used speech data is using 40 speech command data and 10 digits extracted form each 15 of male and female speaker spoken menu control command of Embedded system. Since, in many times, ARM CPU is adopted in embedded system, it's peformed porting the speech recognition engine on ARM core evaluation board. And do the recognition test with select set 1 and set 3 parameter that has good recognition rate on commander and no digit after the several tests using by 5 proposal recognition parameter sets. The recognition engine of recognition rate shows 95%, speech commander recognizer shows 96% and digits recognizer shows 94%.

• 대한기계학회논문집A
• /
• 제36권11호
• /
• pp.1371-1379
• /
• 2012

본 논문에서는 직접분사 가솔린엔진 부품에 의해서 발생하는 진동에 대한 기여도를 분석하는 방법을 제시한다. 본 연구에서는 부분기여도함수를 적용하여 부품 상호간의 관련성에 대한 진동원을 규명 하는데 사용하였다. 직접분사 가솔린 엔진 부품의 진동원을 규명하는데 부분기여도함수 방법을 사용하기 위해서는 시스템의 모델링이 필요하며 본 연구에서는 진동 발생 경로를 2 입력과 단일 출력계로 시스템을 모델링하였다. 이 모델링을 증명 하기 위해서, 직접분사가솔린 엔진의 진동원인 고압펌프, 연료레일, 인젝터, 고압센서에 3 축 가속도계 센서로 각 부품의 진동을 측정했다. 이 모델링을 바탕으로 각각의 진동원에 대한 부분기여도 함수를 구했으며, 직접분사 부품들의 각각의 진동 기여도를 계산하였다. 부분기여도 함수를 바탕으로 한 모델링을 통해 각 부품들에서 발생되는 진동 출력 기여 값을 정량적으로 도출하였다.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.45-53
• /
• 2009

In this study, Finite Element Analysis (FEA) was used to decide three kinds of material property of vibration proof rubber with the unique characteristic of non-linear and large deformation. As well, three types of hardness (Hs 50, 55, 60) were compared with the result of fatigue tests, fatigue life was able to be predicted. The request for fatigue life becomes strict more and more as increasing stress under conditions like a compaction, high load and high temperature for parts because it is main characteristics of rubber mount for automotive. Regarding to the fatigue life under dynamic deformation condition, it can be predicted as checking forced deformation extends and its frequency and its strain-life curve. As for material property tests of uniaxial tension test, uniaxial compression test, pure shear test, Ogden model was used for FEA by observing relations between stress and strain's rate as curve fitting. As a result of FEA, fatigue life for rubber mount was predicted and accorded well with the experimental data of fatigue test with hourglass specimens. In addition, its property of the predictable fatigue life method suggested in this study was accorded well with the experimental data by comparing the predicted fatigue life of FEA with the result of fatigue test for rubber component of engine rubber mount.

• Tribology and Lubricants
• /
• 제31권3호
• /
• pp.125-140
• /
• 2015

In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.

• 한국추진공학회지
• /
• 제10권1호
• /
• pp.1-8
• /
• 2006

액체 로켓엔진 연소기에서 음향감쇠에 미치는 음향 공명기의 이중 주파수 동조(bituning) 효과를, 선형 음향해석을 통해 조사하였다. 이중 주파수 동조된 공명기는, 두가지 주요한 음향파 진동 모드인 제1접선 방향(1T) 모드와 제1반경 방향(1R) 모드에 동조된다. 먼저, 단일 주파수 동조된 공명기의 음향감쇠 효과를 조사하였다. 감쇠 성능은, 1T 또는 1R 모드에 동조된 공명기 개수의 함수로서 감쇠인자에 의해 정량화되었다. 다음으로, 이중 주파수 동조된 공명기의 감쇠 특성을 조사하였다 수치해석 결과로부터, 1T와 1R 모드 각각에 동조될 적절한 공명기의 개수를 선정할 수 있다. 더 나아가, 모드 분할 현상에 의한 음향감쇠 효과의 저하를 줄이기 위해 이와 같은 이중 주파수 동조의 개념을 적용하였으며, 이를 통해 최적의 이중 동조 주파수를 찾을 수 있었다.

• 한국태양에너지학회 논문집
• /
• 제30권6호
• /
• pp.118-124
• /
• 2010

In order to develop commercial model of 10kW dish-Stirling solar thermal power system, modification for the exiting facility was taken for a year as a Leading Project in KIER. During the project, solar tracking system, control and monitoring system and high durability reflector were developed and long term operation were performed. The solar tracking system was tested for four months to investigate the degree of precision and adapted to the control system for an actual operation from October in 2009. The sun tracking accuracy of ${\pm}4$ mrad using modified control system was obtained and the system operated successfully during the experimental period. The monitoring system displays engine pressure, electric generation amounts, generator RPM, receiver temperatures, and etc. from Stirling engine and weather data of Direct Normal Irradiation, Horizontal Global Insolation, wind speed & direction, and atmosphere temperature from weather station. According to the operating results in a clear sky day, electric power of 6,890 W was generated at the DNI value of 850 W/$m^2$ and the averaged solar-to-electricity efficiency during a whole day reached to 18.99%. From the overall operating results, linear power generation trend could be observed with increasing DNI value. The solar-to-electricity efficiency achieved to 19% around the DNI value of 700 W/$m^2$ and increased to 20% when the DNI value goes up to 900 W/$m^2$.

• 대한기계학회논문집
• /
• 제12권5호
• /
• pp.1197-1205
• /
• 1988

본 연구에서는 피스톤운동을 톱날파로 근사하였을 때 단열된 실린더를 갖는 스터링기관에 대한 해석적인 해를 구하고자 한다. 실제기관에서 피스톤운동은 기구 학적 구동기구에 따라 상이하지만 대략적으로 정현파가 되며, 이 경우에는 해석적인 해가 존재하지 않으므로 수학적으로 구간선형적인 톱날파로 근사하였다. 비록 이러 한 근사를 도입한 단열해석이라 하더라도 해석적인 해가 존재한다면 등온해석보다는 기관성능의 예측에 더욱 적합함은 당연하다.