• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.425-432
• /
• 2001

This paper presents the studies of the characteristics of dynamic behavior of single layer latticed domes with laminated rubber bearing and establishes the effectiveness of the system. The base isolation system installed between base and structures reduces the responses due to earthquake motions and increases the natural period of structures. Numerical analysis is carried out using modal superposition method and Newmark-βmethod which is linear acceleration method with (equation omitted) : 1/2 and β : 1/6. The time interval Δt for response calculation is 0.001 sec. Damping ratio is 2 % as Rayleigh damping and El Centro NS(1940) as earthquake motion is the input excitation data. The acceleration response of dome with base isolation is reduced to 30 % of the response of non-isolation system. From the results of the numerical studies on the models, it is confirmed that base isolation system effectively suppresses the responses of the domes subjected to horizontal earthquakes.

• 대한기계학회논문집A
• /
• 제40권12호
• /
• pp.1077-1085
• /
• 2016

선형 롤러베어링은 하중이 크고 정밀성이 요구되는 이송장치를 지지하기 위해 광범위하게 사용되는 기계요소이다. 본 논문에서는 외력을 받는 선형 롤러베어링의 변위를 계산하기 위한 새로운 모델링 방법을 제시하였다. 먼저 LM 블록을 강체로 가정하여 롤러와 LM 블록의 지배방정식을 유도하였고 Newton-Raphson법을 이용해 계산하였다. 롤러와 레이스 사이의 접촉하중은 롤러의 형상을 고려하여 슬라이싱 기법을 이용하여 계산하였다. 강체 LM 블록 모델에 의해 계산된 접촉하중을 활용하여 LM 블록의 구조적 변형을 유한요소 모델로부터 계산하였다. 최종적인 변위는 강체 LM 블록을 가정한 모델로부터 계산된 변위와 LM 블록 구조해석 결과를 조합하여 도출하였다. 제안된 방법에 의한 결과와 베어링 제작 업체 프로그램 결과와의 비교를 통해 제안된 방법을 검증하였다.

• 한국자기학회:학술대회 개요집
• /
• 한국자기학회 2011년도 자성 및 자성재료 국제학술대회
• /
• pp.7-8
• /
• 2011

Although yttrium iron garnet (YIG) has provided a great vehicle for the study of spin waves in the past, associated difficulties in film deposition and device fabrication using YIG had limited the applicability of spin waves to practical devices. However, microfabrication techniques have made it possible to characterize both the resonant as well as the travelling characteristics of spin waves in permalloy (Py). A variety of methods have been used for measuring spin waves, including Brillouin light scattering (BLS), magneto-optic Kerr effect (MOKE), vector network analyzer ferromagnetic resonance (VNA-FMR), and pulse inductive microwave magnetometry (PIMM). PIMM is one of the most preferred methodologies of measuring travelling spin waves. In this method, an electrical impulse is applied at one of two coplanar waveguides patterned on top of oxide-insulated Py, producing a local disturbance in the magnetization of the Py. The resulting disturbance travels down the Py in the form of waves, and is inductively picked up by the other coplanar waveguide. We investigate the effect of the pulse width of excitation pulses on the generated spin wave packets using both experimental results and micromagnetic simulations. We show that spin wave packets generated from electrical pulses are a superposition of two separate spin wave packets, one generated from the rising edge and the other from the falling edge, which interfere either constructively or destructively with one another, depending upon the magnitude and direction of the field bias conditions. A method of spin wave amplitude modulation is also presented by the linear superposition of spin waves. We use interfering spin waves resulting from two closely spaced voltage impulses for the modulation of the magnitude of the resultant spin wave packets.

• 한국지진공학회논문집
• /
• 제1권4호
• /
• pp.1-9
• /
• 1997

본 논문은 고층건물의 지진응답해석에서 탄성 및 탄소성 응답스펙트럼 해석법에 대하여 고찰한 것이다. 선형 구조물의 지진응답 해석에 널리 사용되고 있는 응답스펙트럼법은 여러 연구자들에 의해 서로 다른 모드 조합방법으로 제안되었으며, 이들 조합방법에 따른 차이점을 상세히 검토하였다. 탄소성 지진응답해석에 응답스펙트럼법은 아직 널리 사용되고 있지 못한 실정이다. 본 연구에서는 장주기를 갖는 고층 건물의 탄소성 지진응답해석에 응답스펙트럼을 확장하여 적용하는 방법을 제시한다. 본 논문에서 제안한 탄소성 응답스펙트럼법을 이용하면, 고층건물의 예비 설계에서 시간이력해석 대신으로 보다 간편히 탄소성 응답치를 예측하는 도구로서 활용할 수 있을 것으로 사료된다.

• 한국경영과학회지
• /
• 제23권4호
• /
• pp.97-109
• /
• 1998

In this paper, we propose a new approach to solve stochastic fluid flow models applied to the analysis of ceil loss of an ATM multiplexer. Existing stochastic fluid flow models have been analyzed by using linear differential equations. In case of large state space, however. analyzing stochastic fluid flow model without numerical errors is not easy. To avoid this numerical errors and to analyze stochastic fluid flow model with large state space. we develope a new computational algorithm. Instead of solving differential equations directly, this approach uses iterative and numerical method without calculating eigenvalues. eigenvectors and boundary coefficients. As a result, approximate solutions and upper and lower bounds are obtained. This approach can be applied to stochastic fluid flow model having general Markov chain structure as well as to the superposition of heterogeneous ON-OFF sources it can be extended to Markov process having non-exponential sojourn times.

• 한국수산과학회지
• /
• 제20권5호
• /
• pp.457-462
• /
• 1987

Stochastic stability criterias for ocean wave analysis add simulation are studied using the data simulated by the linear superposition method. To clarify the criterias, the effects of the simulation parameters on the variance of stochastic properties of ocean waves are investigated, and the stable conditions of the parameters are estimated through the comparative study on the stochastic properties of simulated waves and well-known ocean waves. The simulation parameters considered are high frequency cut-off, data length, and number and phase angle of component waves. Statistical characteristics analysed are wave height, period and steepness, and the formation of groups of higher waves, resonance periods, steeper higher waves and extreme run-length of the run.

• Wind and Structures
• /
• 제31권6호
• /
• pp.509-522
• /
• 2020

Wind load is the principal cause for a large number of the collapse of transmission lines around the world. The transmission line is traditionally designed for wind load according to a linear equivalent method, in which dynamic effects of wind are not appropriately included. Therefore, in the present study, incremental dynamic analysis is utilized to investigate the stability behavior of a 400 kV transmission line under wind load. In that case, the effects of vibration of cables and aerodynamic damping of cables were considered on the stability behavior of the transmission line. Superposition of the harmonic waves method was used to calculate the wind load. The corresponding wind speed to the beginning of the transmission line collapse was determined by incremental dynamic analysis. Also, the effect of the yawed wind was studied to determine the critical attack angle by the incremental dynamic method. The results show the collapse mechanisms of the transmission line and the maximum supportable wind speed, which is predicted 6m/s less than the design wind speed of the studied transmission line. Based on the numerical modeling results, a retrofitting method has been proposed to prevent failure of the tower members under design wind speed.

• 한국농공학회논문집
• /
• 제48권6호
• /
• pp.45-56
• /
• 2006

The finite element method is a practical tool to compute the response of the irregularly layered soil deposit to the base-rock motions. The method is useful not only in estimating the interaction between the structure and the surrounding soil as a whole and the local behavior of the contacting area in detail, but also in predicting the resulting behavior of the superstructure affected by such soil-structure interactions. However, the computation of finite element analysis is marched in the time domain (TD), while the site response analysis has been carried out mostly in the frequency domain (FD) with equivalent linear analysis. This study is intended to compare the results of the TD and FD analysis with focus on the peak response accelerations and the predominant frequencies, and thus to evaluate the applicability and the validity of the finite element analysis in the site response analysis. The comparison shows that one can obtain the results very close to that of FD analysis, from the finite element analysis by including sufficiently large width of foundation in the model and further by applying partial mode superposition. The finite element analysis turned out to be well agreeing with FD analysis in their computed results of the peak acceleration and the acceleration response spectra, especially at the surface layer.

• 한국해양공학회지
• /
• 제19권6호통권67호
• /
• pp.58-63
• /
• 2005

The estimation of springing responses for recent ships is carried out, and application to a ship design is described. To this aim, springing effects on hull girder were re-evaluated, including non-linear wave excitations and torsional vibrations of the hull. The Timoshenko beam model was used to calculate stress distribution on the hull girder, using the superposition method. The quadratic strip method was employed to calculate the hydrodynamic forces and moments on the hull. In order to remove the irregular frequencies, we adopted 'rigid lid' on the hull free surface level, and addedasymptotic interpolation along the high frequency range. Several applications were carried out on the following existing ships: The Bishop and Price's container ship, S-175 container ship, large container, VLCC, and ore carrier. One of them is compared with the ship measurement result, while another with that of the model test. The comparison between the analytical solution and the numerical solution for a homogeneous beam-type artificial ship shows good agreement. It is found that Most springing energy comesfrom high frequency waves for the ships having low natural frequency and North Atlantic route etc. Therefore, the high frequency tail of the wave spectrum should be increased by $\omega$$\^{-3}$ instead of $\omega$$\^{-4}$ or $\omega$$\^{-5}$ for the springing calculation.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2004년도 학술대회지
• /
• pp.173-178
• /
• 2004

The estimation of springing responses for recent ships are carried out and application to a ship design are described. To this aim, springing effects on hull girder were re-evaluated including non-linear wave excitations and torsional vibrations of the hull. The Timoshenko beam model was used to calculate stress distribution on the hull girder by the superposition method. The strip method was employed to calculate the hydrodynamic forces and moments on the hull. In order to remove the irregular frequencies, we adopted 'rigid lid' on the hull free surface level and added asymptotic interpolation along the high frequency range. Several applications to the existing ships were carried out. They are Bishop and Price's container ship, S-175 container ship, large container, VLCC and ore carrier. One of them is compared with ship measurement result while another with that of model test. Comparison between analytical solution and numerical one for homogeneous beam type artificial ship shows good agreement. It is found that most springing energy came from high frequency waves for the ships having low natural frequency and North Atlantic route etc. Therefore, the high frequency tail of the wave spectrum should be increased by $\omega^{-3}\;instead\;of\;\omega^{-4}\;or\;\omega^{-5}$ for springing calculation.