• 한국전자파학회논문지
• /
• 제18권11호
• /
• pp.1279-1290
• /
• 2007

본 논문에서는 복합 빔 패턴들을 형성하기 위해 오프셋 선형 급전 배열에 의해 공간 급전되는 원통형 하이브리드 안테나에 대하여 기술한다. 선형 급전 배열은 12개의 마이크로스트립 패치 소자들로 구성되며, 수평면에서 $90^{\circ}$의 구형 빔 패턴을 형성한다. 그리고, 수직면에서 $-5^{\circ}{\sim}-25^{\circ}$ 범위에 걸쳐 코씨컨트 빔 패턴을 형성하기 위해 선형 급전 배열에 의해 원통형 반사판상의 수직 곡선이 성형화 된다. IMT-2000 서비스 대역에서 동작하는 $140{\times}50\;cm$ 크기의 원통형 반사판 개구면을 갖는 하이브리드 안테나 시제품을 설계 및 제작하였으며, 또한 안테나의 전기적 성능들을 측정하고 그 결과들을 분석하였다.

• 정보통신설비학회논문지
• /
• 제7권1호
• /
• pp.41-58
• /
• 2007

A compact and broadband $4{\times}1$ array antenna was developed for 3G smart antenna system testbed. The $4{\times}1$ uniform linear array antenna was designed to operate at 1.885 to 2.2GHz with a total bandwidth of 315MHz. The array elements were based on the novel broadband L-probe fed inverted hybrid E-H (LIEH) shaped microstrip patch, which offers 22% size reduction to the conventional rectangular microstrip patch antenna. For steering the antenna beam, a commercial variable attenuator (KAT1D04SA002), a variable phase shifter (KPH350SC00) with four units each, and the corporate 4-ways Wilkinson power divider which was fabricated in-house were integrated to form the beamforming feed network. The developed antenna has an impedance bandwidth of 17.32% ($VSWR{\leq}1.5$), 21.78% ($VSWR{\leq}2$) with respect to center frequency 2.02GHz and with an achievable gain of 11.9dBi. The design antenna offer a broadband, compact and mobile solution for a 3G smart antenna testbed to fully characterized the IMT-2000 radio specifications and system performances.

• 정보통신설비학회논문지
• /
• 제5권1호
• /
• pp.43-59
• /
• 2006

A compact and broadband $4\times1$ array antenna was developed for 3G smart antenna system testbed. The $4\times1$ uniform linear away antenna was designed to operate at 1.885 to 2.2GHz with a total bandwidth of 315MHz. The array elements were based on the novel broadband L-probe fed inverted hybrid E-H (LIEH) shaped microstrip patch, which offers 22% size reduction to the conventional rectangular microstrip patch antenna. For steering the antenna beam, a commercial variable attenuator (KAT1D04SA002), a variable phase shifter (KPH350SC00) with four units each, and the corporate 4-ways Wilkinson power divider which was fabricated in-house were integrated to form the beamforming feed network. The developed antenna has an impedance bandwidth of 17.32% $(VSWR\leq1.5)$, 21.78% $(VSWR\leq2)$ with respect to center frequency 2.02GHz and with an achievable gain of 11.9dBi. The design antenna offer a broadband, compact and mobile solution for a 3G smart antenna testbed to fully characterized the IMT-2000 radio specifications and system performances.

• 한국전자파학회논문지
• /
• 제20권3호
• /
• pp.280-288
• /
• 2009

본 논문에서는 좁은 빔 특성을 가지고 35 dB 이상의 부엽 레벨(Side Lobe Level: SLL)을 가지는 Chebyshev 전류 분포의 선형 배열 안테나를 위한 고전력, 저손실의 스트립라인 10-출력 전력분배 기를 설계, 제작하였다. T-junction 전력분배기를 기본 구조로 하여 단위 셀을 설계하였고, 설계된 단위 셀을 결합하여 전체 전력분배기를 설계하였다. 설계 시 특성 개선을 위하여 다중 임피던스 변환기와 변형된 링 하이브리드 구조를 적용하였고 커넥터 구조의 변경을 통한 동축선로-스트립라인 천이 구조의 개선으로 반사 및 삽입 손실 특성을 개선하였다.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2000년도 종합학술발표회 논문집 Vol.10 No.1
• /
• pp.345-349
• /
• 2000

A microstrip polarized 8${\times}$2 linear phased array antenna with four 4-bit phase shifters is designed at 10 GHz. The 180$^{\circ}$and 90$^{\circ}$ sections of the phase shifter are of the switched line type, and the rests are of the loaded line type. A 2${\times}$2 sequential sub-array is adopted for a broad axial ratio bandwidth. The construction of the array antenna is of the tile type placing the phase shifters on the same layer containing the feed network. The element spacing is chosen to be 0.45λ$\sub$0/ to exclude the grating lobe. Measurement results show a gain 9.69 dB at broadside and 8.3 dB at the beam-tilt angle of 16$^{\circ}$ by imposing a progressive phase of 90$^{\circ}$.

• Tribology and Lubricants
• /
• 제30권3호
• /
• pp.139-145
• /
• 2014

Nowadays, most micro-patterns are manufactured during flow line production. However, a conventional rotary chemical mechanical polishing (CMP) system has a limited throughput for the fabrication of large and flexible electronics. To overcome this problem, we propose a novel linear roll-CMP system for the planarization of large-area electronics. In this paper, we present a statistical analysis on the linear roll-CMP process of copper-clad laminate (CCL) to determine the impacts of process parameters on the material removal rate (MRR) and its non-uniformity (NU). In the linear roll-CMP process, process parameters such as the slurry flow rate, roll speed, table feed rate, and down force affect the MRR and NU. To determine the polishing characteristics of roll-CMP, we use Taguchi's orthogonal array L16 (44) for the experimental design and F-values obtained by the analysis of variance (ANOVA). We investigate the signal-to-noise (S/N) ratio to identify the prominent control parameters. The "higher is better" for the MRR and "lower is better" for the NU were selected for obtaining optimum CMP performance characteristics. The experimental and statistical results indicate that the down force and roll speed mainly affect the MRR and the down force and table feed rate determine the NU in the linear roll-CMP process. However, over 186.3 N of down force deteriorates the NU because of the bending of substrate. Roll speed has little relationship to the NU and the table feed rate does not impact on the MRR. This study provides information on the design parameter of roll-CMP machine and process optimization.

• 한국전자파학회논문지
• /
• 제12권7호
• /
• pp.1057-1066
• /
• 2001

본 논문에서는 전자기적으로 결합하는 다이폴을 이용하여 직선편파를 복사하는 마이크로스트립 안테나의 설계에 관하여 기술하였다. 다이폴의 위치에 의해 서로 다른 직선편파를 가지는 안테나의 해석 및 설계는 FDTD 법으로 행하였다. 급전선로와 복사소자간의 상호결합을 고려한 단일 소자 안테나의 설계로부터 각 편파에 대한 설계파라미터들을 구했으며, 이를 이용한 어레이 설계에서 Offset을 변화시켜 복사전력을 조절할 수 있었다. 또한 어레이 소자간의 간격을 조정함으로써 원하는 방향으로의 지향각을 설계할 수 있었다. 5 소자 어레이 안테나를 제작하여 측정을 행하였고, 이들 결과는 이론치와 잘 일치하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1142-1143
• /
• 2008

As well known, the maximum power point tracking (MPPT) is an important role in photovoltaic (PV) power systems. MPPT finds and maintains the operation of PV at the maximum power point when the irradiation and cell-temperature change. In this paper, the studied system includes a PV array, a Buck-Boost DC/DC converter, a DC/AC inverter and it is connected to the three phase power system. The solar array operates as a non-linear voltage source. The P&O algorithm with power feed-back is used to control the operating point of PV array at the maximum power point. The effects of irradiation and cell-temperature on the dynamic responses are also considered.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.321-322
• /
• 2002

This paper presents study of effects of cutting parameters such as cutting speed, feed rate and depth of cut on the surface roughness in hard turning. Taguchi Method and linear regression model of design parameters were utilized to identify the controlling process parameters that can monitor the surface roughness in the hard turning operation. In the process optimization, experimental planning was performed using the orthogonal array and concept of the signal-to-noise ratio. Cutting parameters such as speed, feed rate, and depth of cut were selected as process parameters and the ANOVA analysis showed that feed rate and cutting speed had more effect on the roughness variation that depth of cut.

• 천문학회보
• /
• 제41권2호
• /
• pp.66.2-66.2
• /
• 2016

KASI and NAOJ are making collaborating efforts to implement faster mapping capability into the new 275-500 GHz Atacama Submillimeter Telescope Experiment focal plane array (FPA). Feed horn antenna is one of critical parts of the FPA. Required fractional bandwidth is almost 60 % while that of traditional conical horn is less than 50 %. Therefore, to achieve this wideband performance, we adopted a horn of which the corrugation depths have a longitudinal profile. A profiled horn has features not only of wide bandwidth but also of shorter length compared to a linear-tapered corrugated horn, and lower cost fabrication with less error can be feasible. In our design process the flare region is represented by a cubic splined curve with several parameters. Parameters of the flare region and each dimension of the throat region are optimized by a differential evolution algorithm to keep >20 dB return loss and >30 dB maximum cross-polarization level over the operation bandwidth. To evaluate RF performance of the horn generated by the optimizer, we used a commercial mode matching software, WASP-NET. Also, Gaussian beam (GB) masks to far fields were applied to give better GB behavior over frequencies. The optimized design shows >23 dB return loss and >33 dB maximum cross-polarization level over the whole band. Gaussicity of the horn is over 96.6 %. The length of the horn is 12.5 mm which is just 57 % of the ALMA band 8 feed horn (21.96 mm).