• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.97-97
• /
• 2009

The use of thin plate increases due to the need for light weight in large ship. Thin plate is easily distorted and has residual stress by welding heat. Therefore, the thin plate should be carefully joined to minimize the welding deformation which costs time and money for repair. For one effort to reduce welding deformation, it is very useful to predict welding deformation before welding execution. There are two methods to analyze welding deformation. One is simple linear analysis. The other is nonlinear analysis. The simple linear analysis is elastic analysis using the equivalent load method or inherent strain method from welding experiments. The nonlinear analysis is thermo-elastic analysis which gives consideration to the nonlinearity of material dependent on temperature and time, welding current, voltage, speed, sequence and constraint. In this study, the welding deformation is analyzed by using thermo-elastic method for PCTC(Pure Car and Truck Carrier) which carries cars and trucks. PCTC uses thin plates of 6mm thickness which is susceptible to welding heat. The analysis dimension is 19,200mm(length) * 13,825mm(width) * 376mm(height). MARC and MENTAT are used as pre and post processor and solver. The boundary conditions are based on the real situation in shipyard. The simulations contain convection and gravity. The material of the thin block is mild steel with $235N/mm^2$ yield strength. Its nonlinearity of conductivity, specific heat, Young's modulus and yield strength is applied in simulations. Welding is done in two pass. First pass lasts 2,100 second, then it rests for 900 second, then second pass lasts 2,100 second and then it rests for 20,000 second. The displacement at 0 sec is caused by its own weight. It is maximum 19mm at the free side. The welding line expands, shrinks during welding and finally experiences shrinkage. It results in angular distortion of thin block. Final maximum displacement, 17mm occurs around welding line. The maximum residual stress happens at the welding line, where the stress is above the yield strength. Also, the maximum equivalent plastic strain occurs at the welding line. The plastic strain of first pass is more than that of second pass. The flatness of plate in longitudinal direction is calculated in parallel with the direction of girder and compared with deformation standard of ${\pm}15mm$. Calculated value is within the standard range. The flatness of plate in transverse direction is calculated in perpendicular to the direction of girder and compared with deformation standard of ${\pm}6mm$. It satisfies the standard. Buckle of plate is calculated between each longitudinal and compared with the deformation standard. All buckle value is within the standard range of ${\pm}6mm$.

• Earthquakes and Structures
• /
• 제19권3호
• /
• pp.215-226
• /
• 2020

A self-centering wall (SCW) is a lateral resistant rocking system that incorporates posttensioned (PT) tendons to provide a self-centering capacity along with dampers to dissipate energy. This paper investigates the rocking responses of a SCW with base viscous dampers under a sinusoidal-type pulse considering yielding and fracture behaviour of the PT tendon. The differences in the overturning acceleration caused by different initial forces in the PT tendon are computed by the theoretical method. The exact analytical solution to the linear approximate equation of motion is also provided for slender SCWs. Finally, the effects of the ductile behaviour of PT tendons on the rocking response of a SCW are analysed. The results demonstrate that SCWs exhibit two overturning modes under pulse excitation. The overturning region with Mode 1 in the PT force cases separates the safe region of the wall into two parts: region S1 with an elastic tendon and region S2 with a fractured tendon. The minimum overturning acceleration of a SCW with an elastic-brittle tendon becomes insensitive to excitation frequency as the PT force increases. After the plastic behaviour of the PT tendon is considered, the minimum overturning acceleration of a SCW is increased significantly in the whole range of the studied w_g/p.

• 대한조선학회논문집
• /
• 제54권6호
• /
• pp.447-452
• /
• 2017

A rigid body supported by 4 linear springs has been analyzed, to investigate the effects of eccentricities on the vibration responses for naval shipboard equipments supported by elastic mounts. Considering mount eccentricity (the location of the center of spring reaction forces relative to the mass center) and excitation force eccentricity (the location of the center of the excitation force relative to the mass center), the vibration phenomena have been formulated and discussed. Also, the effects of the eccentricities have been evaluated and discussed for the elastically mounted naval shipboard equipment. Results show that the mount eccentricity has little effects on the structure-borne noise above the natural frequency of the system, however the excitation force eccentricity has significant effects all over the frequency range.

• 한국지반공학회지:지반
• /
• 제3권1호
• /
• pp.53-64
• /
• 1987

도로포장의 구조평가 및 유지관리를 위하여 매우 효율적인 장비로 알려진 Dynaflect의 이용이 날 로 증가하고 있어, 이에 대한 연구가 절실하다. 따라서 본 연구에서는 도로포장에 사용되는 재료의 탄성계수에 따른 해석모질을 설정하고, 이를 다층토 이론에 근거한 콤퓨터 프로그램을 통하여 Dyn select의 처짐곡선을 산출함으로써 표층 두께와 탄성계수에 따른 분산도의 특성을 연구하였다.

• Tribology and Lubricants
• /
• 제15권4호
• /
• pp.343-353
• /
• 1999

The role of viscosity index improver's(Ⅶ) additives for modem engine lubrication is complex. Under the condition of atmosphere or low shear rate, the characteristics of Ⅶ added lubricant is verified and quoted frequently for mathematical model of lubricant behavior. However, recent research shows that added lubricant has the characteristics of shear thinning at high shear rate condition although it performs well enough over the whole range of working temperature. At high shear rate, they show significant decrease of apparent viscosity irrespective of temperature. Many experimental researches verify that Ⅶ added lubricant shows boundary film layer formation on the solid surface as well as shear thinning effect by its polymeric molecular characteristics. The intend of our research is to verify the effects of Ⅶ from the viewpoint of continuum mechanics, because conventional Reynolds'equation with only pressure-viscosity relation cannot fully predict the lubricant behavior under the Ⅶ added condition. In these aspects, Reynolds'equation of Newtonian fluid model lacks the reflection of real fluid behavior and there is no way to explain the non-linear characteristics of Ⅶ added lubricant. In this research, we mathematically modeled the Ⅶ added lubricant behaviors which are the characteristics of non-Newtonian fluid behavior at high shear rate and boundary film formation on the solid surface. The consideration of elastic deformation in the contact region is also included in our computation and finally the converged film pressure and the film thickness with elastic deformation are obtained. The results are compared with those of Newtonian fluid model.

• Steel and Composite Structures
• /
• 제1권4호
• /
• pp.411-426
• /
• 2001

This paper treats the failure analysis of prestressing steel wires with different kinds of localised damage in the form of a surface defect (crack or notch) or as a mechanical action (transverse loads). From the microscopical point of view, the micromechanisms of fracture are shear dimples (associated with localised plasticity) in the case of the transverse loads and cleavage-like (related to a weakest-link fracture micromechanism) in the case of cracked wires. In the notched geometries the microscopic modes of fracture range from the ductile micro-void coalescence to the brittle cleavage, depending on the stress triaxiality in the vicinity of the notch tip. From the macroscopical point of view, fracture criteria are proposed as design criteria in damage tolerance analyses. The transverse load situation is solved by using an upper bound theorem of limit analysis in plasticity. The case of the cracked wire may be treated using fracture criteria in the framework of linear elastic fracture mechanics on the basis of a previous finite element computation of the stress intensity factor in the cracked cylinder. Notched geometries require the use of elastic-plastic fracture mechanics and numerical analysis of the stress-strain state at the failure situation. A fracture criterion is formulated on the basis of the critical value of the effective or equivalent stress in the Von Mises sense.

• Structural Engineering and Mechanics
• /
• 제4권1호
• /
• pp.25-35
• /
• 1996

This paper describes a continuum variational formulation for design optimization of nonlinear structures in the elastic-plastic domain, where unloading and reloading of the structures are allowed to occur. The Total Lagrangian procedure is used for the description of the structural deformation. The direct differentiation approach is used to derive the sensitivities of the various structural response measures with respect to the design parameters. Since the material goes into the inelastic range and unloading and reloading of the structure are allowed to occur, the structural response is path dependent and an additional step is needed to integrate the constitutive equations. It can be shown, consequently, that design sensitivity analysis is also path-dependent. The theory has been discretized by the finite element technique and implemented in a structural analysis code. Mathematical programming approach is used for the optimization process. Numerical applications on trusses are performed, where cross-sectional areas and nodal point coordinates are treated as design variables. Optimal designs have been obtained and compared by using two different strategies: a two level strategy where the levels are defined accordingly the type of design variables, cross sectional areas or node coordinates, and optimizing simultaneously with respect to both types of design variables.

• Advances in materials Research
• /
• 제6권3호
• /
• pp.257-278
• /
• 2017

A simple closed-form solution to calculate the interfacial shear and normal stresses of retrofitted concrete beam strengthened with thin composite plate under mechanical loads including the creep and shrinkage effect has been presented in this paper. In such plated beams, tensile forces develop in the bonded plate, and these have to be transferred to the original beam via interfacial shear and normal stresses. Consequently, debonding failure may occur at the plate ends due to a combination of high shear and normal interfacial stresses. These stresses between a beam and a soffit plate, within the linear elastic range, have been addressed by numerous analytical investigations. Surprisingly, none of these investigations has examined interfacial stresses while taking the creep and shrinkage effect into account. In the present theoretical analysis for the interfacial stresses between reinforced concrete beam and a thin composite plate bonded to its soffit, the influence of creep and shrinkage effect relative to the time of the casting, and the time of the loading of the beams is taken into account. Numerical results from the present analysis are presented both to demonstrate the advantages of the present solution over existing ones and to illustrate the main characteristics of interfacial stress distributions.

• Journal of Welding and Joining
• /
• 제7권1호
• /
• pp.28-35
• /
• 1989

The fatigue crack growth behavior in GTA butt welded joints of Al-Alloy 5052-H38 was examined using Single Edge Notched(SEN) specimens. It is well known that welding residual stress has marked influence on fatigue crack growth rate in welded structure. In the general area of fatigue crack growth in the presence of residual stress, it is noted that the correction of stress intensity factor (K) to account for residual stress is important for the determination of both stress intensity factor range(.DELTA.K) and stress ratio(R) during a loading cycle. The crack growth rate(da/dN) in welded joints were correlated with the effective stress intensity factor range(.DELTA.Keff) which was estimated by superposition of the respective stress intensity factors for the residual stress field and for the applied stress. However, redistribution of residual stress occurs during crack growth and its effect is not negligible. In this study, fatigue crack growth characteristics of the welded joints were examined by using superposition of redistributed residual stress and discussed in comparison with the results of the initial welding residual stress superposition.

• 한국식품과학회지
• /
• 제15권2호
• /
• pp.183-188
• /
• 1983

한국 재래식 국수류인 밀국수와 냉면국수의 점탄성을 연구하기 위하여 실험실에서 tensile시험기계를 만들고 이것을 이용하여 국수발에 대한 creep test를 실시하였다. 밀국수 및 냉면국수 모두 최초 단시간의 creep에서는 선형점탄성(linear viscoelastic)을 나타내었으나 creep시간이 경과함에 따라 비선형 점탄성을 나타내었다. 변형력 범위가 $4{\times}10^4-14{\times}10^4\;dyn\;cm^{-2}$일때 밀국수는 120초간, 냉면국수는 60초간 선형 점탄성을 나타내었다. 2000초 동안의 creep시험에서 추산된 밀국수의 탄성계수(elastic modulus)는 $7.0{\times}10^5\;dyn\;cm^{-2}$이었으며 냉면국수는 $3.9{\times}10^5\;dyn\;cm^{-2}$이었다. 변형력의 증가에 따른 점성변화를 평가한 결과 밀가루 반죽에서 보고된 결과와는 정반대 현상인 stress-hardening 성질을 나타내었다.