• Journal of the Korean Operations Research and Management Science Society
• /
• v.22 no.1
• /
• pp.25-49
• /
• 1997

Printed circuit board (PCB) assembly line configuration is characterized by very long set-up times and high work in process (WIP) inventory level. The scheduling method can significantly reduce the set-up times and WIP inventory level. Greedy sequence dependent scheduling (GSDS) method is proposed based on the current methods. The proposed method is compared with the current method in terms of three performance measures: line throughput, average WIP inventory level, and implementation complexity.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.155-159
• /
• 2001

In this paper, an on-line dead-time compensation method based on a time delay control approach is presented. The disturbance voltages caused by the dead time are estimated in an on-line manner by the time delay control without any additional circuits and off-line experimental measurements. And the estimated disturbance voltages are fed to voltage references in order to compensate the dead-time effects. The proposed method is applied to a PM synchronous motor drive system and implemented by using software of a digital signal processor (DSP) TMS320C31. Experiments are carried out for this system and the results well demonstrate the effectiveness of the proposed method.

• Structural Engineering and Mechanics
• /
• v.76 no.2
• /
• pp.239-250
• /
• 2020

This paper deals with free vibration of plates with steps and internal line supports by using a modified matched interface and boundary (MMIB) method. Different kinds of interfaces caused by steps, rigid and elastic line supports and their combinations are taken into account. Detailed MMIB procedures for dealing with these different interfaces are presented. Various examples are chosen to illustrate the accuracy and convergence of MMIB method. Numerical results show that the proposed MMIB is a highly accurate and convergent approach for solving the title issue. This study will extend the application range of MMIB method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.10
• /
• pp.982-987
• /
• 2009

On the controller switching time, even though on-line/off-line controller outputs are the same, a problem which deteriorates the performance of bumpless transfer can happen in case that any discrepancy between the two controller inputs is transferred directly to the controller output. In this paper, we analyze the cause of that phenomenon in existing research results and propose a new method which improves that problem. In order to solve this problem, the off-line controller is augmented to an anti-windup structure and an improved bumpless transfer method is derived by using the changed input of the off-line controller instead of the plant input. We exemplify the performance of the proposed method by comparing with the performance of the existing method via numerical examples.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.558-561
• /
• 2002

In the embodiment of power line modem, the important elements are selection of a suitable line-coupler, choice of a modulation method good for channel environments, and an efficient data coding method etc. In this paper an appropriate modulation method was implemented their results in details and verified by the simulations. The data compensation request techniques that uses error checking was discussed. Finally, application of other modulation method by detection of error rate per bit according to vary of channel error caused by electric equipment that is connected to power line was studied.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.1
• /
• pp.40-47
• /
• 2010

This paper presents a simultaneous localization and mapping (SLAM) of an indoor hallway environment using Rao-Blackwellized particle filter (RBPF) along with a line segment as a landmark. Based on the fact that fluent line features can be extracted around the ceiling and side walls of hallway using vision sensor, a horizontal line segment is extracted from an edge image using Hough transform and is also tracked continuously by an optical flow method. A successive observation of a line segment gives initial state of the line in 3D space. For data association, registered feature and observed feature are matched in image space through a degree of overlap, an orientation of line, and a distance between two lines. Experiments show that a compact environmental map can be constructed with small number of horizontal line features in real-time.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1309-1317
• /
• 2007

In this paper, the Induced voltage on transmission line by lightning was calculated using FDTD method and the lightning parameters such as peak voltage, rise time, and decay time for the lightning location and line length were analyzed. To verify the results, lightning induced voltage was measured in the field using real telecommunication line. Results from the collected data were compared with the calculated results. It was found that the rise time and the decay time were increased as the line length and the distance between the line and lightning location were increased. Also, the peak voltage was affected more by the overhead line length than by the total line length, while the rise time and the decay time were more affected by the total line length.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.3
• /
• pp.13-20
• /
• 1983

A method for the detecting defined vertices is described in this paper. An alogrithm detecting vertex position by means of calculating an error and distinguishing the defined inner and outer corners by the chain code of line segments is described. To calculate the error, virtual links are detected by means of a jointing relations of line segments for a contour. And so an error is calculated by measuring a minimum distance from a jointing point between the line segments to virtual link. As a result, this method is more flexible and effective than conventional Freeman's method.

• Journal of Wind Energy
• /
• v.9 no.4
• /
• pp.47-56
• /
• 2018

This paper introduces an active power dependent standard characteristic curve, Q(P) to compensate for voltage variations due to the output of distributed generation. This paper presents an efficient control method of grid-connected inverters by comparing and analyzing voltage variation magnitude and line loss according to the compensation method. Voltage variations are caused not only by active power, but also by the change of reactive power flowing in the line. In particular, the system is in a relatively remote place in a coastal area compared with existing power plants, so it is relatively weak and may not be suitable for voltage control. So, since it is very important to keep the voltage below the normal voltage limit within the specified inverter capacity and to minimize line loss due to the reactive power. we describe the active power dependent standard characteristic curve, Q(P) method and verify the magnitude of voltage variation by simulation. Finally, the characteristics of each control method and line loss are compared and analyzed.

• Proceedings of the KSR Conference
• /
• 2003.10b
• /
• pp.157-162
• /
• 2003

The curved line in construction of railroad is inevitable. Also it needs a transition curve when the straight line connects to curved line. In this research, by establishing the reciprocal relations of inner, center and outer track, we will present the calculation method of construction-center line in normal double-track railroad which uses cubic parabolic type as a transition curve.