• 산업기술연구
• /
• 제19권
• /
• pp.135-145
• /
• 1999

This thesis is to investigate the sliding behavior of cantilever retaining wall by using the commercially available program of FLAC to simulate its behavior numerically. Cantilever retaining walls with flat base, sloped base and base with shear key, uniform surcharges being applied on the surface of backfill, were investigated to figure out appropriate location of shear key beneath the base of wall and, thus, its applicability to field condition was assessed by comparing the analyzed results to each other. On the other hand, previously performed centrifuge model test results (Eum, 1996) were analyzed numerically with FLAC to compare test results with respect to characteristics of load-settlement of surcharges and load-lateral movement of wall. Based on the failure mechanism observed during centrifuge tests, limit equilibrium method of finding the ultimate load inducing the sliding failure of wall was used to compare with values of the ultimate load obtained from conventional method of limit equilibrium method. Therefore, appropriate location of shear key was determined to mobilize the maximum resistance against sliding failure of wall.

• Computers and Concrete
• /
• 제24권4호
• /
• pp.303-311
• /
• 2019

The depth of superstructure is the summation of the height of girders and the thickness of the deck floor. In this study, it is aim to determine the maximum span length of girders and minimum depth of the superstructure of prestressed concrete I-girder bridge. For this purpose the superstructure of the bridge with the width of 10m and the thickness of the deck floor of 0.175m, which the girders length was changed by two meter increments between 15m and 35m, was taken into account. Twelve different girders with heights of 60, 75, 90, 100, 110, 120, 130, 140, 150, 160, 170 and 180 cm, which are frequently used in Turkey, were chosen as girder type. The analyses of the superstructure of prestressed concrete I girder bridge was conducted with I-CAD software. In the analyses AASHTO LRFD (2012) conditions were taken into account a great extent. The dead loads of the structural and non-structural elements forming the bridge superstructure, prestressing force, standard truck load, equivalent lane load and pedestrian load were taken into consideration. HL93, design truck of AASHTO and also H30S24 design truck of Turkish Code were selected as vehicular live load. The allowable concrete stress limit, the number of prestressed strands, the number of debonded strands and the deflection parameters obtained from analyses were compared with the limit values found in AASHTO LRFD (2012) to determine the suitability of the girders. At the end of the study maximum span length of girders and equation using for calculation for minimum depth of the superstructure of prestressed concrete I-girder bridge were proposed.

• Structural Engineering and Mechanics
• /
• 제50권3호
• /
• pp.305-322
• /
• 2014

Reliability-based design limit states and associated partial load factors provide a consistent level of design safety across bridge types and members. However, limit states in the current AASHTO LRFD have not been developed explicitly for the situation encountered by integral abutment bridges (IABs) that have unique boundary conditions and loads with inherent uncertainties. Therefore, new reliability-based limit states for IABs considering the variability of the abutment support conditions and thermal loading must be developed to achieve IAB designs that achieve the same safety level as other bridge designs. Prestressed concrete girder bridges are considered in this study and are subjected to concrete time-dependent effects (creep and shrinkage), backfill pressure, temperature fluctuation and temperature gradient. Based on the previously established database for bridge loads and resistances, reliability analyses are performed. The IAB limit states proposed herein are intended to supplement current AASHTO LRFD limit states as specified in AASHTO LRFD Table 3.4.1-1.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.17-22
• /
• 2001

This paper is the first of companion papers, which investigate port-masking effects on lean misfire limit. Port-masking was applied to commercial SOHC 3-valve and DOHC 4-valve engine by inserting masking plates between manifold and port. To induce various conditions of stratification, six types of masking plates were applied. The masking plates were placed in the upstream of injector to prevent wall wetting and two ports were not separated to permit both fuel and air entering through masked port. The results were compared with those by conventional port throttling. The results show that lean misfire limit mainly depends on masking direction, that is, high lean misfire limit is achieved when the port near the spark plug is masked. The mechanism of stratification by masking is different from axial stratification by port throttling. In this case, the rich mixture entering through masked port plays a very important role in the stratification process.

• Geomechanics and Engineering
• /
• 제11권2호
• /
• pp.235-252
• /
• 2016

This paper presents a new numerical solution of the ultimate lateral capacity of rectangular piles in clay. The two-dimensional plane strain finite element was employed to determine the limit load of this problem. A rectangular pile is subjected to purely lateral loading along either its major or minor axes. Complete parametric studies were performed for two dimensionless variables including: (1) the aspect ratios of rectangular piles were studied in the full range from plates to square piles loaded along either their major or minor axes; and (2) the adhesion factors between the soil-pile interface were studied in the complete range from smooth surfaces to rough surfaces. It was found that the dimensionless load factor of rectangular piles showed a highly non-linear function with the aspect ratio of piles and a slightly non-linear function with the adhesion factor at the soil-pile interface. In addition, the dimensionless load factor of rectangular piles loaded along the major axis was significantly higher than that loaded along the minor axis until it converged to the same value at square piles. The solutions of finite element analyses were verified with the finite element limit analysis for selected cases. The empirical equation of the dimensionless load factor of rectangular piles was also proposed based on the data of finite element analysis. Because of the plane strain condition of the top view section, results can be only applied to the full-flow failure mechanism around the pile for the prediction of limiting pressure at the deeper length of a very long pile with full tension interface that does not allow any separation at soil-pile interfaces.

• 대한기계학회논문집A
• /
• 제34권9호
• /
• pp.1293-1298
• /
• 2010

본 연구에서는 인공감육엘보에 대해 내압 및 굽힘의 복합하중을 작용시킨 실 배관 실증실험으로부터 생성한 회전각 대비 모멘트 곡선으로부터 감육결함 엘보에서 소성변형이 시작되는 1 배탄성구배법에 기초한 OES 탄성하중과 2 배탄성구배법에 기초한 TES 소성하중의 거동 및 상관관계를 살펴보았다. ASME 에서도 제시하고 있는 TES 소성하중은 균열손상에 따른 배관계통 구조 건전성 상실을 배제하면서도 지속사용을 허용할 수 있는 대체 관리 기준으로서 적합한 것으로 판단된다.

• 한국지반공학회논문집
• /
• 제21권10호
• /
• pp.113-122
• /
• 2005

신뢰성 기반의 한계상태설계법(Limit State Design; LSD)의 지반공학적 적용은 세계적으로 확산추세이며, 북미지역의 경우 일부 시방서에 하중 및 저항에 의한 LRFD 설계법이 지반공학적 설계에 적용되고 있다. 그러나 지금까지 제안되어 온 지반공학적 저항계수는 상당히 포괄적인 값이며, 이와 관련된 연구는 아직까지 초기단계라 할 수 있다. 콘관입시험은 대표적인 현장시험으로 특히 말뚝 설계에서 유용하게 활용되고 있으며, 다양한 말뚝 지지력 산정법이 제시되어 왔다. 본 연구에서는 콘관입시험을 이용한 항타 말뚝 지지력 평가를 위한 저항계수를 산정하고자 한다. 이를 위하여 여러 지역에서 수행된 말뚝재하시험과 콘관입시험 결과를 수집하여 확률적 분석을 수행하였으며, 이를 종합하여 저항계수 산정에 적용하였다. 본 연구에서는 전체지지력뿐만 아니라 말뚝의 선단 및 주면 지지력 각각에 대한 저항계수 또한 도출하고자 하였다. 저항계수 산정 결과, 목표신뢰도지수 $2.0{\sim}2.5$의 범위에서 전체지지력에 대한 저항계수 $0.35{\sim}0.55$범위를 나타내었다.

• 대한토목학회논문집
• /
• 제39권1호
• /
• pp.13-24
• /
• 2019

이 연구에서는 국내 도로교 한계상태설계법에서 콘크리트부재의 설계를 위하여 적용하고 있는 재료계수의 문제점을 제기하고, 잘 정립된 최적화 과정에 의한 재료계수를 제안하였다. 신뢰도분석을 통하여 현 설계기준의 하중계수와 제안 재료계수가 목표신뢰도지수 보다 높은 신뢰도수준을 확보하고 있음을 보이고, 역신뢰도해석을 통하여 목표신뢰도지수를 잘 근사할 수 있는 하중계수를 제시하였다. 유로코드에서 제시하고 있는 기본 개념에 근거하여 신뢰도기반 하중-재료계수 결정법을 정식화하였다. 제안된 접근법이 신뢰도개념에 의하여 유도되었지만, 이 접근법에 의하여 계산된 하중-재료 계수가 목표신뢰도지수를 정확히 만족시키지 못하는 요인으로서 재료와 부재간에 존재하는 불확실성의 차이를 지적하고, 이러한 차이를 고려하지 않는 유로코드의 개념적 문제점을 제기하였다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1156-1163
• /
• 2010

The bi-directional high pile load test(BDH PLT) does not have weaknesses found in the existing bi-directional low pile load test(BDL PLT); it has strong economics, is unbound by load capacity limit and secures quality stability of working piles. In this study, Verification the field found a very high capacity level of stability and reliability of the BDH PLT, as well as outstanding field applicability. Field verifications reaffirmed the advantage of the BDH PLT device, which was capable of loading 90 MN capacities as maximum. It was also found to be durable enough to load high capacity with ease.

• 한국자동차공학회논문집
• /
• 제8권1호
• /
• pp.157-162
• /
• 2000

The ball bearings are the widely-used machine elements in many machineries. They support not only the radial and the axial force but also the moment in many cases. To simply determine the limit load which can be maintained on an ball bearing or survived in wanted life, the combined the radial and axial force with the moment is converted to the equivalent radial or axial load. However, it is not easy to calculate the equivalent load on the ball bearings. So the simplified equations to evaluate the dynamic and static equivalent load considering the axial force and moment are proposed in this analysis. And the modified equation for the static equivalent radial load with the moment and the axial load is proposed. It is desired that these equations are effectively refered in designing the machineries where the ball bearings are installed.