• 대한조선학회지
• /
• 제3권1호
• /
• pp.11-18
• /
• 1966

In a polarized light field, triangular plate bracket specimen of CR-39 with lightening hole were subjected to tension. The variables of the models used in the experiment were taken in the range of length-depth $ratio=0.583{\sim}1.715$, eccentricity of lightening hole from the geometrical center of $bracket=-1/4"{\sim}+1/4"$, and the lightening hole $diameter=1/2"{\sim}2"$. The isoclinics were drawn and from those the stress trajectories were constructed. Then the distributions of boundary stress around the lightening holes were determined from the isochromatic fringe pattern. The conclusions reached in this investigation are as follows: 1. Maximum stresses of the hole boundary are gradually increased when the diameter of the lightning hole increase. 2. Maximum stresses of the lightning hole boundary are decreased gradually when the eccentricity of the lightning hole from the geometrical center of the bracket to the farther side from the free end. 3. If the minimum distances from the free end of the brackets to the lightening hole boundaries are equal, the variation of the maximum stresses are in a small range for the change of lightening hole diameter and its location. 4. When the length-depth ratios are smaller than 0.8, the maximum stresses increase steeply. In the range of $0.8{\sim}1.2$ maximum stresses increase gradually and thereafter increase rapidly when the length-depth ratio of the bracket increase for the same diameter of a lightening hole.

• 한국항공우주학회지
• /
• 제36권10호
• /
• pp.979-987
• /
• 2008

항공우주 구조물의 설계 시, 과도한 응력집중을 방지하기 위해 경감공의 위치를 변경해야 하는 경우가 종종 발생한다. 이러한 위치 최적 설계를 위해서는 경감공의 위치 갱신에 따라 변경된 구조 형상을 반영할 수 있도록 재 모델링을 수행해야 한다. 널리 사용되는 재 모델링 기법으로는 재 격자 생성기법을 들 수 있다. 그러나 구조물의 형상이 변경될 때마다 격자를 재생성 할 경우 많은 시간이 소요되며, 특히 사면체나 삼각형에 비해 좋은 성능을 가진 육면체나 사각형 격자 사용에 제약이 따르게 된다. 본 논문에서는 이러한 문제점을 보완하기 위해 이동최소자승법 기반의 중첩 격자 기법과 유전자 알고리듬을 이용한 새로운 위치 최적 설계 알고리듬을 제안하였으며, 제안된 위치 최적 설계 알고리듬의 성능을 평가하기 위해 2차원 구조물의 경감공 위치 최적 설계를 수행하였다.

• Journal of Biosystems Engineering
• /
• 제23권3호
• /
• pp.259-270
• /
• 1998

An automatic seedling transplanter, employed an innovative plug-seedling feeder was developed by improving the problems of conversational feeding and transplanting mechanisms. With conventional methods, missing and damage rates of seedling were high for long seedlings over 20cm and also breaking seed-bed was frequently observed. Thus, a pushout-bucket slide-hopper type trandsplanter was devised and tested. Test results of picking and transferring accuracies of the developed transplanter are as follows : A prototype transplanter performed with 1.5% of missing rate. The deviations of horizontal feed ranged from -0.3mm to 2.8mm and averaged 0.673mm for the 128-hoe test tray : and ranged from -lmm to ＋3mm and averaged 0.785mm for the 200-hole test tray. The deviations could decrease with precise manufacturing and lightening the mechanism. The maximum and deviations of vertical feed were -2.3mm and + 1mm, respectively, for the 128-hole test tray ; and were ＋3mm and ＋2.5mm, respectively, for the 200-hole test tray. The missing rate, seeding bruise rate and seed-bed damage rate were esitmate to be 1.3％, 0.4% and 3.5％, respectively, with the developed automatic transplanter.

• 한국분무공학회지
• /
• 제9권4호
• /
• pp.77-82
• /
• 2004

This paper describes the improvement of engine cooling system. To improve engine cooling performance, the authors approached in two ways. One is to increase water pump performance, changing of impeller shape and lightening of material were carried out. The second one is cooling efficiency rise, which were investigated with head gasket coolant flow passage optimization with flow visualization technique. The test results show that water pump performance was increased effectively, reduction of pump drive torque, and increase of pump flow-rate and pressure rise. Gasket hole pattern optimization test results represent an optimized head coolant flow which stands cross flow from exhaust to intake port side and small vortex were removed.

• Design & Manufacturing
• /
• 제11권1호
• /
• pp.1-6
• /
• 2017

In these days, due to generalization of using smart mobile phone and wearable device such as smart watch, demand of Cover-glass and touch screen panel for protecting display increases. With increasing the demand of Cover-glass, slimming technique is promising for weight lightening, zero bezel. Cover-glass produced by this technique is required to decreasing thickness with increase strength. In the Cover-glass manufacturing process, mechanical processing and chemical processing has improve in the strength. Generally, Diamond electrodeposition wheel is used in mechanical process. Reinforced glass with the characteristics of the brittle and high hardness was manufactured by using a diamond electrodeposition wheel. At this time, Because of surface of the tool present non-uniform distribution of diamond particle, it has generate Loading of wheel and it has been decrease life of grinding tool, efficiency of grinding, quality and shape accuracy of workpiece. Thus Research is needed to controling particle distribution of diamond electrodeposition wheel uniformly. And it is necessary to study micro hole machining such as proximity senser hole, speaker hole positioned Cover-glass. Reinforced glass with the characteristics of the brittle and high hardness is difficult to machining. Processing of reinforced glass have generated wear of tool, micro cracks. Also, it is decreasing shape accuracy. In this paper, We conducted a study on how to control particle distribution uniformly about the diamond tool manufactured using elecetodeposition processing. It analyzed the factors that affect the arrangement of the particles in the electrodeposition process by design of experiment. And There is produced the grinding tool, which derives an optimum deposition conditions, for processing Cover-glass edge and the machinability was evaluated.