• International Journal of Aerospace System Engineering
• /
• v.1 no.1
• /
• pp.16-20
• /
• 2014

Recently, various kinds of study on light weight structure are performing in the world. The Al honeycomb sandwich structural type adopt for improvement of lightness and structural stability to major part structure of aircraft or spacecraft. Adhesion badness properties of adhesive and adhesion properties of fillet mainly studied about al honeycomb structure. But study for adhesive properties of sandwich construction with surface treatment of Aluminum alloy barely performed. In this study, adhesive film was used between Al and honeycomb core of honeycomb panel[1]. The study for adhesive properties of sandwich construction with surface treatment of AA 5052 skin was performed.

• Journal of Bio-Environment Control
• /
• v.4 no.2
• /
• pp.232-239
• /
• 1995

This study was carried out to get required torque data needed to design and develop a roll-up ventilation system in a pipe-constructed plastic film green-house. The results obtained from this study are as follows : 1. The required torques of a roll-up ventilation system in greenhouse are the functions of its length. The torques should multiplied by the conversion coefficients (2.0 in ceiling vent, 1.8 in side vent) in case of application. 2. In constructing pipe-constructed plastic film greenhouse, a shaft pipe is the largest essential element in roll - up shaft weight constitution which have an effect on the required torques. Therefore, the pipe should be light using nonferrous materials like aluminum alloy. 3. A planetary reduction ventilator of differential ring gear type is suitable for a roll-up ventilation system, because it can make high efficient reduction just using the first step shift.

• Journal of Power System Engineering
• /
• v.19 no.1
• /
• pp.50-55
• /
• 2015

This study takes AC8A, which is a representative light weight alloy as matrix, and nickel as reinforcement for its superior properties. The manufacturing method applied in this study required low pressure for the infiltration of the metal matrix into the reinforcement. Porous Ni was applied as preform. The fabrication was conducted under 0.3 MPa at 600, 700 and 750 degrees centigrade, respectively. Intermetallic compounds Al3 generated between Al and Ni were observed in the composites. Microstructure, Vickers' hardness and wear characteristics of the composites were also investigated. The result indicates that the structures of compounds created at 650 degree centigrade were distributed densely; the grain size of the substances and the compounds was increased with the infiltration temperature.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1118-1123
• /
• 2003

Based on the design requirements(size, strength, structure, weight, and etc.) for the rubber-tired AGT vehicle, carbody made of aluminum alloy is designed. The analysis of strength and stiffness is performed in the designed carbody, which results in the modification for optimal shapes and structures. It consists of a under frame, side frame, roof frame, end frame and forehead frame. After the carbody manufactured, tests are performed, which are vertical load test, longitudinal compressive load test, twisting load test, twisting natural frequency measurement, bending natural frequency measurement and 3 points supporting test. Results of them can guarantee a structural safety.

• Journal of the Korean institute of surface engineering
• /
• v.25 no.2
• /
• pp.57-65
• /
• 1992

Increasing demands of high corrosion resistant sheet steels for the automotive body panels have been leading to a tendency toward heavier coatings of electroplated sheet steels. The specimens were prepared from lab-scale electroplating simulator with various coating weights of zinc, zinc-iron and zinc-nickel coated sheet steels and evaluated in the light of the application for the automotive body panels. Corrosion resistances by sacrificial action were improved with increasing coating weights for all electroplated sheet under survey, but blistering resistances of pure zinc coated sheet steels were not as much. On the other hand, the adhesions of heavy alloy coatings showed poor powdering performances by the external compressive or tensile forces.

• Journal of Korea Foundry Society
• /
• v.31 no.5
• /
• pp.243-248
• /
• 2011

Magnesium alloys have many advantages such as light-weight, high machinability, damping capacity, etc. So magnesium alloy parts have been used in transportation, mobile phone, military industries. Because of HCP atomic structure, Magnesium is very difficult in plastic deformation process, so most of magnesium products are fabricated by casting process. Magnesium alloys have low heat-capacity, high fluidity and low Fe solubility. For these reasons it is more suitable than aluminum in mass-production by casting. And various casting technologies have been developed. So casting technologies for magnesium developed recently is discussed in this paper.

• Composites Research
• /
• v.25 no.3
• /
• pp.82-89
• /
• 2012

This paper investigated the composite materials application examples and trends in the future to the solid rocket motor cases. The motor case must be stiff and tolerate at the high pressures, and light weight. In accordance to these kind of requirements, the composite materials showed the adaptable efficiency, and glass fibers, aramid, carbon fibers are applied to orderly. The comparison of the motor case efficiencies of the D6AC steel alloy, aramid, carbon fibers results in the carbon fibers best. Also the capacity of the payload will be increased more than 20% by using the high strength ones.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.91-97
• /
• 2003

In many countries such as Japan, France and so on, the number of double-deck trains has been dramatically increased for the purpose of public traffic. Several researchers have performed feasiblilty studies related to the operations of double deck rolling stock vehicles in Korea since 2001. In recent years, rolling stock vehicles are required to have light weight to save energy consumption and maintenance costs. For these reasons, the standard EMU vehicle developed by KRRI and Kwan-Ju EMU(Electric Multi Unit) are made of aluminum extruded panels. The concept model of a double-deck rolling stock vehicle investigated in this study is also designed to use AEP(Aluminum Extruded Panel). In this paper, the methods related to the structural strength improvements of the car body are proposed through careful modifications of thicknesses and shapes of AEP.

• Journal of Auto-vehicle Safety Association
• /
• v.10 no.3
• /
• pp.38-44
• /
• 2018

Conventional brake system was used for passenger cars and SUV for a long time. However, the high performance brake system has strongly required because of increase of engine power and customer's favorites etc. In this paper, a new high performance brake system for Europe was proposed. For this system, the high performance caliper and disc were newly developed. The superiorities of the developed high performance brake system were verified via heat capacity, hydraulic stiffness, corrosion and harsh braking mode test. Also, the high performance caliper and disc for the light-weight were applied to AL-Alloy and can obtain the weight reduction effect of 2.9 kg per vehicle. Finally, a developed high performance brake system is expected to be used for realization of the high performance at the same platforms.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.1-4
• /
• 2008

Fuel cells have the potential of providing several times higher energy storage densities than those possible using current state-of-the-art lithium-ion batteries, but current energy density of fuel cell system is not better than that of lithium-ion batteries. To achieve the high energy density, volume and weight of fuel cell system need to be reduced by miniaturizing system components such as stack, fuel tank, and balance-of-plant. In this paper, the thin flexible PCB (Printed circuit board) is used as a current collector to reduce the stack volume. Two end plates are made from light weight aluminum alloy plate. The plate surface is wholly oxidized through the anodizing treatment for electrical insulation. The opening rate of cathode plate hole is optimized through unit cell performance measurement of various opening rates. The performances are measured at room temperature and ambient pressure condition without any repulsive air supply. The active area of MEA is 10.08 $cm^2$ and active area per a unit cell is 1.68 $cm^2$. The peak power density is about 210 mW/$cm^2$ and the air-breathing planar stack of 2 Wis achieved as a small volume of 18 cc.