• 한국농공학회지
• /
• 제44권4호
• /
• pp.107-113
• /
• 2002

The pipe framed and arch shape plastic greenhouse, which is the most popular greenhouse in Korea, is relatively weak in snowdrift. Reinforcement of rigid frame or column is required to reduce the damage from heavy snow in this type. But additional rigid frames or columns decrease light transmissivity or workability, and increase construction cost. So it is desirable to prepare some temporary poles and to install them when the warning of heavy snow is announced. This study was carried out to develop the temporary pole supporting system using galvanized steel pipes for plastic housing and to evaluate the safe snow load on a temporary pole. A pipe connector, which is inserted in the top of pipe used in the temporary pole and supports the center purline, was designed and manufactured to be able to carry the upper loads safely. And a bearing plate was safely designed and manufactured in order to carry the loads acting on it to the ground. When temporary poles of ${\phi}$ 25 pipe are installed at 2.4m interval, it shows that the single span plastic greenhouses with 5~7 m width are able to support the additional snow depth of 13.9~25.3 cm beyond the snow load supported by main frame.

• 한국산학기술학회논문지
• /
• 제15권8호
• /
• pp.4763-4768
• /
• 2014

본 최근 비닐하우스의 개폐를 위해 사용되는 스틸 관 대신에 가볍고 내식성이 우수한 알루미늄 관의 사용이 확대되었다. 하지만 이러한 알루미늄 관은 스틸 관에 비해 큰 열팽창 계수를 가지고 있기 때문에 겨울철에 스틸관에 비해 상대적으로 동파에 취약한 문제가 제기되고 있다. 본 논문은 기존 연구사례를 바탕으로 수치해석을 이용하여 동파가능성을 예측하였다. 이를 위해 알루미늄 관 내부의 얼음은 냉동되면서 최대 50%까지 부피가 팽창한다고 가정하여 얼음의 부피가 팽창되는 과정에서 관의 기계적 열적 거동을 관찰하였다. 해석결과 관 내부에 완전히 찬 얼음이 팽창할 때 높은 내압이 발생하며, 동시에 알루미늄 관은 항복강도 이상의 응력이 발생하였고, 얼음의 팽창율이 약 6 ~ 7%에 이르면 알루미늄의 연신율 17%에 이르게 되기 때문에 알루미늄관은 완전히 동파될 것으로 판단되었다. 따라서 이와 같은 동파해석을 통해 관은 좌 우의 유입구를 완전하게 밀봉하여 근원적으로 관내부에 얼음이 생성되지 않도록 하는 것이 매우 중요함을 알 수 있다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.168-171
• /
• 2004

If a research trend present in and outside the country is often seen, the structure measurement method of having used PZT and the optical fiber (FBG) will be the actual condition which has accomplished the stock. In order to manage such cracks, time, efforts and expense are required. Such a method has many difficulties in application of a structure by the difficult problem of the measurement range, and the expensive sensor price. Progressive cracks were generated by fracture of glass pipe sensor. Moreover, the experiment which can detect damage propriety by external Light Emitting Diode by damaging a glass pipe by load change with the application of switch using strain gage of a glass pipe was conducted.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.173.1-173
• /
• 2001

This paper proposes the methodology in image processing algorithm that estimates the pose of the pipe crawling robot. The pipe crawling robots are usually equipped with a lighting device and a camera on its head for monitoring and inspection purpose. The proposed methodology is using these devices without introducing the extra sensors and is based on the fact that the position and the intensity of the reflected light varies with the robot posture. The algorithm is divided into two parts, estimating the translation and rotation angle of the camera, followed by the actual pose estimation of the robot. To investigate the performance of the algorithm, the algorithm is applied to a sewage maintenance robot.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2002년도 봄 학술발표회 논문집
• /
• pp.413-420
• /
• 2002

Recent experimental research results of connection method between steel pipe pile and concrete footing are provided based on various experimental observations. It gives a shedding light toward developing better and concrete connection method for steel pipe pile at the field application. In this study, the newly developed method is tested for compressive, pull put and combination load including moment with carefully designed monitoring system. The measured data show that new method have at least equivalent or better load resistant capacities compared with those of specified method in Korea Highway Corporation design code. It is also tried to define and investigate the load transfer mechanism for new method.

• Journal of Welding and Joining
• /
• 제16권5호
• /
• pp.119-133
• /
• 1998

To implement full automation in pipe welding, it si most important to develop special sensors and their related systems which act like human operator when detecting irregular groove conditions. In this study, an automatic pipe Gas Metal Arc Welding (GMAW) system was proposed to full control pipe welding procedure with intelligent sensor systems. A five-axes manipulator was proposed for welding torch to automatically access to exact welding position when pipe size and welding angle were given. Pool status and torch position were measured by using a weld-pool image monitoring and processing technique in root-pass welding for weld seam tracking and weld pool control. To overcome the intensive arc light, pool image was captured at the instance of short circuit of welding power loop. Captured image was processed to determine weld pool shape. For weld seam tracking, the relative distance of a torch position from the pool center was calculated in the extracted pool shape to move torch just onto the groove center. To control penetration of root pas, gap was calculated in the extracted pool image, and then weld conditions were controlled for obtaining appropriate penetration. welding speed was determined with a fuzzy logic, and welding current and voltage were determined from a data base to correspond to the gap. For automatic fill-pass welding, the function of human operator of real time weld seam control can be substituted by a sensor system. In this study, an arc sensor system was proposed based on a fuzzy control logic. Using the proposed automatic system, root-pass welding of pipe which had gap variation was assured to be appropriately controlled in welding conditions and in torch position by showing sound welding result and good seam tracking capability. Fill-pass welding by the proposed system also showed very successful result by tracking along the offset welding line without any control of human operator.

• Journal of Advanced Marine Engineering and Technology
• /
• 제38권10호
• /
• pp.1200-1205
• /
• 2014

The effect of nanofluids on the heat transfer performance of a pulsating heat pipe has been experimentally investigated. Water-based diamond nanofluid and aluminium oxide ($Al_2O_3$) nanofluid were tested in the concentration range of 0.5-5%. The pulsating heat pipe was constructed using clear Pyrex tubes of 1.85 mm in inner diameter in order to visualize the pulsating action. The total number of turns was eight each for heated and cooled parts. The supply temperatures of heating water and cooling water were fixed at $80^{\circ}C$ and $25^{\circ}C$ respectively. The liquid charging ratio of the nanofluid was 50-70%. The test results showed that the case of 5% concentration of diamond nanofluid showed 18% increase in heat transfer rate compared to pure water. The case of 0.5% concentration of $Al_2O_3$ nanofluid showed 24% increase in heat transfer rate compared to pure water. But the increase of $Al_2O_3$ nanofluid concentration up to 3% did not show further enhancement in heat transfer. It is also observed that the deposited nanoparticles on the tube wall played a major role in enhanced evaporation of working fluid and this could be the reason for the enhancement of heat transfer by a nanofluid, not the enhanced thermal conductivity of the nanofluid.

• 한국구조물진단유지관리공학회 논문집
• /
• 제8권1호
• /
• pp.221-229
• /
• 2004

강관말뚝 머리를 확대기초 내에 얕게 근입하는 방법은 작업성과 배근의 용이성 등의 이점 때문에 일본과 우리나라에서 널리 적용되고 있다. 또한 일본은 몇 차례의 시방서 개정으로 말뚝머리 연결방법을 표준화하기에 이르렀고, 다양한 연결방법에 대하여 실험적 연구와 이론적 연구가 축적되었다. 따라서 국내에서도 최근 말뚝머리 보강설계에 대한 연구의 필요성이 대두되어 본 연구에서는 도로교 시방서에서 제시하는 대표적인 강관 말뚝머리 연결부 방법B 속채움방법에 대한 구조적 성능 및 특성을 파악하고자 단순 인발실험 및 단순 압입실험을 실시하여 말뚝머리 연결부의 거동 메카니즘을 규명하고자 한다. 또한 인발 및 압입실험의 결과에서 미끄럼 방지턱을 용접대신 고장력볼트로 접합하여 사용했을 경우 구조적 거동안정성을 파악하고자 한다.

• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.87-100
• /
• 2000

HC and CO emissions during the cold start contribute the majority of the total emissions in the legislated driving cycles. Therefore, in order to minimize the cold-start emissions, the fast light-off techniques have been developed and presented in the literature. One of the most encouraging strategies for reducing start-up emissions is to place the light-off catalyst, in addition to the main under-body catalyst, near the engine exhaust manifold. This study numerically consider three-dimensional, unsteady compressible reacting flow in the light-off and under body catalyst to examine the impact of a light-off catalyst on thermal response of the under body catalyst and tail pipe emission. The effect of flow distribution on the temperature distribution and emission performance have also been examined. The present results show that flow distribution has a great influence on the temperature distribution in the monolith at the early stage of warm-up process and the ultimate conversion efficiency of light-off catalyst is severly deteriorated when the space velocity is above $100,000hr^{-1}$.

• Journal of Biosystems Engineering
• /
• 제26권5호
• /
• pp.441-448
• /
• 2001

Hot air heater with light oil combustion is used as the most common heater for greenhouse heating in the winter season. However, exhaust gas heat discharged to atmosphere through chimney reaches up to 10~20% of total heat capacity of the oil burred. In order to recover the heat of this exhaust gas and to use for greenhouse heating, the heat pipe type exhaust heat recovery system was manufactured and tested in this experiment. The system consisted of a heat exchanger made of heat pipes, ø15.88${\times}$600mm located in the rectangular box of 675(L)${\times}$425(W)${\times}$370(H)mm, an air suction fan and air ducts. The number of heat pipe was 60, calculated considering the heat exchange amount between exhaust gas and air and heat transfer capacity of a heat pipe. The working fluid of heat pipe was acetone because acetone is known for its excellent heat transfer capacity. The system was attached to the exhaust gas path. According to the performance test it could recover 53,809 to 74,613kJ/h depending on the inlet air temperature of 12 to -12˚at air flow rate of 1.100㎥/h. The temperature of the exhaust gas left the heat exchanger dropped to 100$^{\circ}C$ from 270$^{\circ}C$ after the heat exchange between the suction air and the exhaust gas.