• Journal of Environmental Health Sciences
• /
• v.24 no.2
• /
• pp.74-79
• /
• 1998

This study was conducted to evaluate the surfactant solutions which influence solvent extraction from light hydrocarbon contaminated soils. Nine characteristic compounds were studied: benzene, toluene, ethylbenzene, o-xylene, mxylene, p-xylene, n-propylbenzene, 1,2,4-trimethylbenzene, and n-butylbenzene which were found in gasoline. Adsee-799 and Witbreak DRA-22 showed some extractive capacity for light hydrocarbons from soil. There was no added advantage obtained by using other surfactants in this study. No removal of contaminants from soil was observed when the surfactant concentration was 0.5 percent or below. When the surfactant concentration was 4 percent, the average recovery for some hydrocarbons was 10.8 percent, which was the best obtained at these levels. There was 10 percent surfactant contribution for methanol extraction from soil with the Witbreak DPG-482 and Witbreak DRA-22. This study provided a useful screening technique for procedures that can be used to remediate soils contaminated with light hydrocarbons.

• Journal of Environmental Health Sciences
• /
• v.23 no.4
• /
• pp.82-90
• /
• 1997

This study was conducted to establish an ideal condition for obtaining maximum extraction efficiencies using an array of soil types and under a wide variety of conditions. Nine characteristic compounds were studied: benzene, toluene, ethylbenzene, o-xylene, m-xylene, p-xylene, n-propylbenzene, 1,2,4-trimethylbenzene, and n-butylbenzene which were found in gasoline. Increasing the moisture content resulted in decreased recovery, and recovery of hydrocarbons from wet soils was significantly lower than from dry soils. For the batch extraction process, 4 hours of extraction time was sufficient to give optimum recovery of the contaminants. With methanol as an extraction solvent, maximum recovery time appeared to be reached quicker for BTEX components than with 2-propanol. The 2 to 1 ratio of solvent/soil was chosen as a compromise to provide for the indicated minimum solvent use and high extraction efficiency. The 0.4 mg/g soil contamination was adequate to show quantitative recovery. The percent recovery of BTEX was concentration dependent more than the semivolatile compounds. Methanol and 2-propanol consistently gave higher efficiency than water. Methanol was superior to 2-propanol in removing contaminants from silty clay loam soil. Using the most efficient extraction procedure, the average recovery of the light hydrocarbons from the three soils was 66 percent. Recoveries were also dependent on soil type, solvent type, extraction time, solvent amount, contaminant concentration, and compounds volatility. This study provided a useful screening technique for procedures that can be used to remediate soils contaminated with light hydrocarbons.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.7
• /
• pp.1320-1332
• /
• 2016

Light hydrocarbons accumulated in subsurface soil by long-term microseepage could favor the anomalous growth of indigenous hydrocarbon-oxidizing microorganisms, which could be crucial indicators of underlying petroleum reservoirs. Here, Illumina MiSeq sequencing of the 16S rRNA gene was conducted to determine the bacterial community structures in soil samples collected from three typical oil and gas fields at different locations in China. Incubation with n-butane at the laboratory scale was performed to confirm the presence of "universal microbes" in light-hydrocarbon microseepage ecosystems. The results indicated significantly higher bacterial diversity in next-to-well samples compared with background samples at two of the three sites, which were notably different to oil-contaminated environments. Variation partitioning analysis showed that the bacterial community structures above the oil and gas fields at the scale of the present study were shaped mainly by environmental parameters, and geographic location was able to explain only 7.05% of the variation independently. The linear discriminant analysis effect size method revealed that the oil and gas fields significantly favored the growth of Mycobacterium, Flavobacterium, and Pseudomonas, as well as other related bacteria. The relative abundance of Mycobacterium and Pseudomonas increased notably after n-butane cultivation, which highlighted their potential as biomarkers of underlying oil deposits. This work contributes to a broader perspective on the bacterial community structures shaped by long-term light-hydrocarbon microseepage and proposes relatively universal indicators, providing an additional resource for the improvement of microbial prospecting of oil and gas.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.1
• /
• pp.108-121
• /
• 1998

Using gas chromatography, the light hydrocarbon emissions were analyzed from SI engine fueled with methane and liquified petroleum gas(LPG), and the effects of fuel and engine operating condition were discussed. For this purpose, 14 species of light hydrocarbon including 1, 3-butadiene were separated, calibrated with standard gas, and measured from undiluted emissions. The brake specific hydrocarbon emission(BSHC) and ozone forming potential(BSO)3 were calculated and discussed with the changes of fuel, engine speed, load, fuel/air equivalence ratio, coolant temperature, and spark timing. As a result, exhaust emission was composed of mainly fuel composed of mainly fuel comp- onent and other olefin components of similar carbon number. The olefin components such as ethylene and propylene determine most of the ozone forming potential. The fraction of fuel component in total hydrocarbon emission was bigger with methane fuel than with LPG fuel. Also fuel fraction increased at high speed or high speed or high temperature of exhaust gas, and to lesser extent with high coolant temperature and retarded spark. However, the effect of equivalence ratio had different tendency according to fuels.

• KSBB Journal
• /
• v.13 no.5
• /
• pp.606-614
• /
• 1998

In this study, biodegradation rate of Arabian light crude oil by mixed cultures of selected petroleum-degraders was determined. Their modes of hydrocarbon uptake were then observed to determine whether there are differences in biodegradation rate by the mixed cultures. By the mixed cultures of petroleum-degraders having same modes of hydrocarbon uptake, such as strain US1 and K1 (using pseudo-solubilized hydrocarbons by a biosurfactants), K2-2 and P1(using hydrocarbons by direct contact), CL 180 and IC-10 (mixed type of uptake modes), the biodegradation rates of aliphatics in the crude oil were increased more than those by their pure cultures, about 40%, 25% and 20%, respectively. Biodegradation rate of strain KH3-2 (using only water- dissolved hydrocarbons) was increased by mixed cultures with strain K1, CL180 or IC-10 possessing high emulsifying activity. However, the biodegradation rate of the crude oil was decreased about 20%-40% by the mixed cultures of petroleum-degraders having different mode of hydrocarbon uptake, such as addition of strain US1 or K1 in the cultures of K2-2 or P1. Biosurfactants produced by US1 or K1 seems to enhance the emulsification of crude oil in aqueous phase but inhibit the attachment of K2-2 or P1 to crude oil. As same phenomena, the addition to Triton X-100 into the culture of strain US1, K1, CL180, IC-10 or KH3-2 increased the biodegradation rate, but the addition in the culture of strain K2-2 or P1 decreased the biodegradation rate. The mixed culture made of CL180, IC-10 and KH3-2 degraded 61.5% of aliphatics and 69% of aromatics in 3% (v/v) of Arabian light crude oil added.

• Journal of Microbiology and Biotechnology
• /
• v.3 no.1
• /
• pp.46-50
• /
• 1993

In 12:12 hour light/dark cycle cultivation of D. salina 1650, maximum specific growth rate of 0.59 (l/day) and 0.35 (g-crude hydrocarbons/l/day) were obtained. The cell growth was inhibited at above 15$\times$$10^{-4} (kcal/cm^2/h)$ of light intensity in an outdoor cultivation. It was also showed that temperature is one of the critical growth parameters in the outdoor cultivation. The hydrocarbon production from D. salina 1650 seems to be partially growth related production process, and these algal hydrocarbons can be used for subsituting petroleum directly or through cracking processes. The value of weight fraction carbon of D. salina 1650 was similar to that of Botryococcus braunii and so was the hydrocarbon productivity.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.58.2-58.2
• /
• 2012

Heavy hydrocarbon reforming is a core technology for "Dirty energy smart". Heavy hydrocarbons are components of fossil fuels, biomass, coke oven gas and etc. Heavy hydrocarbon reforming converts the fuels into $H_2$-rich syngas. And then $H_2$-rich syngas is used for the production of electricity, synthetic fuels and petrochemicals. Energy can be used efficiently and obtained from various sources by using $H_2$-rich syngas from heavy hydrocarbon reforming. Especially, the key point of "Dirty energy smart" is using "dirty fuel" which is wasted in an inefficient way. New energy conversion laboratory of KAIST has been researched diesel reforming for solid oxide fuel cell (SOFC) as a part of "Dirty energy smart". Diesel is heavy hydrocarbon fuels which has higher carbon number than natural gas, kerosene and gasoline. Diesel reforming has difficulties due to the evaporation of fuels and coke formation. Nevertheless, diesel reforming technology is directly applied to "Dirty fuel" because diesel has the similar chemical properties with "Dirty fuel". On the other hand, SOFC has advantages on high efficiency and wasted heat recovery. Nippon oil Co. of Japan recently commercializes 700We class SOFC system using city gas. Considering the market situation, the development of diesel reformer has a great ripple effect. SOFC system can be applied to auxiliary power unit and distributed power generation. In addition, "Dirty energy smart" can be realized by applying diesel reforming technology to "Dirty fuel". As well as material developments, multidirectional approaches are required to reform heavy hydrocarbon fuels and use $H_2$-rich gas in SOFC. Gd doped ceria (CGO, $Ce_{1-x}Gd_xO_{2-y}$) has been researched for not only electrolyte materials but also catalysts supports. In addition, catalysts infiltrated electrode over porous $La_{0.8}Sr_{0.2}Ga_{0.8}Mg_{0.2}O_3-{\delta}$ and catalyst deposition at three phase boundary are being investigated to improve the performance of SOFC. On the other hand, nozzle for diesel atomization and post-reforming for light-hydrocarbons removal are examples of solving material problems in multidirectional approaches. Likewise, multidirectional approaches are necessary to realize "Dirty energy smart" like reforming "Dirty fuel" for SOFC.

• Applied Chemistry for Engineering
• /
• v.27 no.5
• /
• pp.546-550
• /
• 2016

Over 60~70% of the domestic soil contamination have occurred by petroleum products. B T E X including benzene, toluene, ethylbenzene, xylene and total petroleum hydrocarbon (TPH) have to be inspected for the contaminated soil by petroleum products. An accurate contamination analysis is necessary to estimate the are of contaminated soil and also establish an appropriate purification scheme. In this study, we analyzed a sectional TPH pattern for current domestic distributed petroleum products. Also, the TPH content was analyzed by compensating the defect of current Korea standard analytic methods for soil where the analytic range is just for $C_8{\sim}C_{40}$. The light distillate petroleum products such as gasoline and solvent 1 showed the maximum of 85% difference in the TPH content between the standard analytic and improved methods.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.5
• /
• pp.30-40
• /
• 1994

The direct-injection stratified-charge engine has the advantages of higher thermal efficiency and less CO and $NO_x$ emission levels than conventional spark ignition engines. However, its actual utilization is prevented by high unburned hydrocarbon emission levels during light-load operations. In this paper, fundamental studies were carried out using a pancake type constant volume bomb. The effects of intensification of local premixing by tangential and radial fuel injection were examined experimentally. Unburned hydrocarbon emission levels with radial fuel injection were shown to be lower than those of tangential fuel injection cases. The stratification and mixing process of fuel jet and combustion process were observed by schlieren photography.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.47-53
• /
• 2000

To overcome the shortage of conventional TWC that is activated at high temperature, higher than 25$0^{\circ}C$, photocatalyst is considered as an new technology. Because the photocatalytic reaction of photocatalyst is not a thermo mechanical reaction, it is necessary to heat the system to start the reaction. It can be activated just by ultra violet light that includes wavelengths shorter than 400 nanometers even at ambient temperature. In this study photocatalytic reduction of hydrocarbon was investigated with a model gas test. To understand the effects of co-existence gases on the hydrocarbon reduction by photoreaction, CO and NO, $O_2, H_2O$ gases those are components of exhaust gases of gasoline engine are supplied with C3H8/N2 to a photoreactor. The photoreactor contains $TiO_2$ photocatalyst powders and a UV bulb. The results show that oxygen is the most important factor to reduce HC emission with photocatalyst. Photocatalyst seems to have a good probability for automotive application to reduce cold start HC emissions.