• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 B
• /
• pp.1155-1156
• /
• 2006

In this paper, we analyzed the effect of EVA Sheet Gel Content depending on curing condition for photovoltaic module. Gel Content was measured by manufacturing Glass/EVA Sheet/Back Sheet scheme at several curing temperature and curing time. And the surface analysis of EVA Sheet depending on process condition could be observed using SEM(Scanning Electron Microscope). Through this experiment, we could confirm that there are differences on Gel Content of EVA Sheet and surface configuration depending on curing temperature and curing time. To find out the optical characteristic dependency on curing condition, Class/EVA Sheet/Glass scheme was fabricated. The optical transmittance of EVA Sheet at visible wavelength was enhanced 5% when compared to Glass/Glass scheme. And the transmittance of $130^{\circ}C$/4min, $110^{\circ}C$/4min, $160^{\circ}C$/6min process condition was higher at ultraviolet wavelength range. These curing conditions could be regarded as the best process for suppression the discoloration speed of EVA Sheet under UV light.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.375-376
• /
• 2010

본 연구는 WCP 대체율 및 오토클레이브 양생시간 변화에 따른 경량기포콘크리트의 미세구조 및 광물분석을 통한 화학적 특성을 검토하였다. 경화체의 미세구조 분석으로부터 수열 반응 후 WCP 대체율 및 양생시간에 관계없이 반응하여 판상형, 섬유형의 결정 구조물의 수화물을 형성한 것을 확인하였다. 또한 Tobermorite(C5S6H5)는 WCP의 구성성분인 결정질 Quartz의 반응에 의한 것으로 추정된다.

• Journal of Korean Dental Science
• /
• 제8권2호
• /
• pp.82-88
• /
• 2015

Purpose: To evaluate the effect of light-curing on the immediate and delayed micro-shear bond strength (${\mu}SBS$) between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramics and RelyX Ultimate when using Single Bond Universal (SBU). Materials and Methods: Y-TZP ceramic specimens were ground with #600-grit SiC paper. SBU was applied and RelyX Ultimate was mixed and placed on the Y-TZP surface. The specimens were divided into three groups depending on whether light curing was done after adhesive (SBU) and resin cement application: uncured after adhesive and uncured after resin cement application (UU); uncured after adhesive, but light cured after resin cement (UC); and light cured after adhesive and light cured resin cement (CC). The three groups were further divided depending on the timing of ${\mu}SBS$ testing: immediate at 24 hours (UUI, UCI, CCI) and delayed at 4 weeks (UUD, UCD, CCD). ${\mu}SBS$ was statistically analyzed using one-way ANOVA and Student-Newman-Keuls multiple comparison test (P<0.05). The surface of the fractured Y-TZP specimens was analyzed under a scanning electron microscope (SEM). Result: At 24 hours, ${\mu}SBS$ of UUI group ($8.60{\pm}2.06MPa$) was significantly lower than UCI group ($25.71{\pm}4.48MPa$) and CCI group ($29.54{\pm}3.62MPa$) (P<0.05). There was not any significant difference between UCI and CCI group (P>0.05). At 4 weeks, ${\mu}SBS$ of UUD group ($24.43{\pm}2.88MPa$) had significantly increased over time compared to UUI group (P<0.05). The SEM results showed mixed failure in UCI and CCI group, while UUI group showed adhesive failure. Conclusion: Light-curing of universal adhesive before or after application of RelyX Ultimate resin cement significantly improved the immediate ${\mu}SBS$ of resin cement to air-abrasion treated Y-TZP surface. After 4 weeks, the delayed ${\mu}SBS$ of the non-light curing group significantly improved to the level of light-cured groups.

• 치위생과학회지
• /
• 제19권1호
• /
• pp.39-47
• /
• 2019

Background: Light-emitting diodes curing unit (LCU), which emit blue light, is used for polymerization of composite resins in many dentistry. Although the use of LCU for light-cured composite resin polymerization is considered safe, it is still controversial whether it can directly or indirectly have harmful biological influences on oral tissues. The aim of this study was to elucidate the biological effects of LCU in wavelengths ranging from 440 to 490 nm, on the cell viability and secretion of inflammatory cytokines in MDPC-23 odontoblastic cells and inflammatory-induced MDPC-23 cells by lipopolysaccharide (LPS). Methods: The MTT assay and observation using microscope were performed on MDPC-23 cells to investigate the cell viability and cytotoxic effects on LCU irradiation. Results: MDPC-23 cells and LPS stimulated MDPC-23 cells were found to have no effects on cell viability and cell morphology in the LCU irradiation. Nitric oxide (NO) and prostaglandin $E_2$ which are the pro-inflammatory mediators, and interleukin-$1{\beta}$ and tumor necrosis factor-${\alpha}$ (TNF-${\alpha}$) which are the proinflammatory cytokines were significantly increased in MCPD-23 cells after LCU irradiation as time increased in comparison with the control. LCU irradiation has the potential to induce inflammation or biological damages in normal dental tissues, including MDPC-23 cells. Conclusion: Therefore, it is necessary to limit the use of LCU except for the appropriate dose and irradiation time. In addition, LCU irradiation of inflammatory-induced MDPC-23 cells by LPS was reduced the secretion of NO compared to the LPS alone treatment group and was significantly reduced the secretion of TNF-${\alpha}$ in all the time groups. Therefore, LCU application in LPS stimulated MDPC-23 odontoblastic cells has a photodynamic therapy like effect as well as inflammation relief.

• 대한소아치과학회지
• /
• 제23권4호
• /
• pp.906-914
• /
• 1996

Due to the various reason, sealing of pit & fissure might be imperfect. One of these reason can be the fracture of sealant material because of the low hardness value of sealing material. The purpose of this in vitro study was to evaluate the microhardness of two different curing type pit and fissure sealants: Dual-cure and Light-cure. The result from the present study can be summarized as follows: 1. All pit and fissure sealants that used in this study showed statistically significant difference in their microhardness of upper and lower surface. (P <0.05) 2. Except of lower surface of teethmate, microhardness of 40-second curing sealant was statistically higher than that of 20-second curing sealant. (P <0.05) 3. In comparison of sealants, microhardness of dual-cure sealant was statistically higher than that of light-cure sealant. Above results suggest that the use of dual-cure sealant and longer curing time are recommended.

• 대한소아치과학회지
• /
• 제24권1호
• /
• pp.139-147
• /
• 1997

Argon laser used in this case report, is special in having two wavelength of 488, 514nm blue-green visible light spectrum. Blue light is used for composite resin polymerization and caries detection. Green light is used for soft tissue surgery and coagulation. Maximum absorption of this laser light occurs in red pigmentation such as hemoglobin. The argon laser may be well-suited for selective destruction of blood clots and hemangioma with minimal damage to adjacent tissues. Argon laser light penetrates tissue to the 1 mm depth, so its thermal intensity is lower than $CO_2$ laser light. Also, due to its short wavelength it can be focused in a small spot and even single gene can be excised by this laser and microscopy. After applicating argon laser to 4 patient for surgical procedure and to 1 patient for curing the composite resin, following results were obtained. 1. Improved visibility were gained due to hemostasis and no specific technique were needed according to easy recontouring of the tissue. 2. Ability to use by contact mode, tactile sense was superior but tissue dragability and accumulation of tissue on the tip needed sweeping motion. 3. Additive local anesthetic procedure was needed. 4. No suture and less curing time reduced chair time, this made argon laser available in pediatric dentistry.

• Restorative Dentistry and Endodontics
• /
• 제32권1호
• /
• pp.28-36
• /
• 2007

본 연구는 광중합형 복합레진 중합 시 기존의 중합법과 가변광도 중합형인 soft start 중합법 및 exponential 중합법 간의 중합수축효과를 비교하고자 하였다. 본 연구를 위해 3종의 복합레진 (Synergy Duo Shade, Z250, Filtek Supreme) 및 3종의 광조사기 (Spectrum 800, Elipar Highlight, Elipar Trilight)를 사용하였다. 총 중합시간은 40초로 일정하게 유지하였으며, 선형 중합수축률의 측정은 linometer를 이용하였으며, 90초간의 선형 수축률을 0.5초 간격으로 측정하였다. 재료별로 각 중합 방법별 시간에 따른 중합수축률을 one-way ANOVA test로 분석하여 최종 중합수축률에 도달하는 시간을 산출하였고, 90초 후 최종 선형 중합수축률을 two-way ANOVA test를 이용하여 재료, 광조사 방법, 재료 및 광조사 방법의 교호작용이 중합수축에 미치는 영향이 있는지를 검증하였다. 또한 90초까지의 선형 중합수축률에 대한 20초까지의 선형 중합수축률의 비를 two-way ANOVA로 비교하고, 각각의 통계치를 95% Scheffe test로 검증하였는바, 다음과 같은 결과를 얻었다 1. Supreme을 제외한 다른 군에서는 재료 및 광조사 방법에 관계없이 대부분의 중합 수축이 광조사 후 20초 이내에 이루어졌다 (p < 0.05). 2. 90초 후, 최종 중합수축률은 재료 (p = 0.000)와 광조사 방법 (p = 0.003) 모두 유의성 있는 영향을 끼쳤으나, 재료와 광조사 방법 상호간의 작용은 영향이 없었다. 3. 90초 후 최종 중합수축률은 총 광에너지가 가장 낮은 exponential 중합법에서 유의성 있게 낮았다 (p < 0.05). 4. 20초까지의 초기 수축률은 soft start와 exponential중합법 등 가변광도 중합이 conventional 중합법에 비하여 유의성 있게 낮은 수축률을 보였다 (p < 0.05). 본 실험 결과만을 토대로 볼 때, 가변광도 중합법은 초기 중합수축 속도를 감소시켜 수축응력을 감소시킨다고 볼 수 있다. 그러나 총 조사 광에너지의 차이로 인해 그 물리적 성질에 영향이 있을 수 있으므로 향후 이에 대한 더 많은 고찰이 필요할 것으로 사료된다.

• 대한치과교정학회지
• /
• 제40권1호
• /
• pp.27-33
• /
• 2010

성인 교정환자의 수요가 증가하면서 보철물 표면에 교정장치를 부착해야 하는 빈도가 늘어나고 있다. 본 연구는 금속표면에 교정장치를 직접 접착하고자 할 때 사용하는 metal primer와 silicoating으로 각각 금합금의 표면을 처리한 후 light emitting diode (LED) 광중합기를 사용하여 광중합을 시행하여 접착력을 평가해 보고자 하였다. Type III gold alloy 표면에 aluminum oxide를 이용한 sandblasting 후 4-META 계열의 metal primer로 처리한 시편과 silica를 이용한 sandblasting 후 silane으로 처리한 시편에 광중합형 접착레진인 Transbond XT를 이용하여 금속 브라켓을 접착하고 접착 후 1시간, 6시간, 24시간 후 전단접착강도의 변화를 비교, 관찰하였다. 측정된 값을 이원분산분석(two-way analysis of variance)을 이용하여 비교하고 두 가지 표면처리 방법 간에 접착강도에 차이가 있는지도 살펴보았다. 연구결과, metal primer에 비하여 silicoating을 시행한 시편에서 높은 전단접착강도가 관찰되었으며, 시간이 경과할수록 접착강도가 증가하는 경향을 보였다. Adhesive remnant index (ARI)에서는 군 간 유의한 차이를 보이지 않았다. LED를 이용하여 광중합을 시행하는 경우 법랑질에 비하여 긴 시간의 광중합을 실시하고 metal primer보다는 silicoating 방법을 사용하는 것이 금합금표면에 교정장치를 부착할 때 더 높은 접착강도를 얻을 수 있을 것이다.

• 한국기계가공학회지
• /
• 제17권2호
• /
• pp.47-53
• /
• 2018

Nowadays, additive manufacturing (AM) technology is a promising process to fabricate complex shaped devices applied in medical and dental services. Among the AM processes, a DLP (digital light processing) type 3D printing process has some advantages, such as high precision, relatively low cost, etc. In this work, we propose a simple method to fabricate precise dental models using a DLP 3D printer. After 3D printing, a part is commonly post-cured using secondary UV-curing equipment for complete polymerization. However, some shrinkage occurs during the post-curing process, so we adaptively control the UV-exposure time on each layer for over- or under-curing to change the local shape-size of a part in the DLP process. From the results, the shrinkage amounts in the post-curing process vary due to the UV-dose in 3D printing. We believe that the proposed method can be utilized to fabricate dental models precisely, even with a change of the 3D CAD model.

• 대한치과교정학회지
• /
• 제34권5호
• /
• pp.429-438
• /
• 2004

본 연구는 Plasma arc light를 이용하여 금속 브라켓의 부착시 광조사 방향, 중합시간 그리고 경화시간이 전단결합강도에 미치는 영향을 평가하기 위해서 시행되었다. 240개의 발거된 소구츠를 16군으로 나눈 후. 광중합기(Plasma arc light와 Halogen light), 중합시간(Plasma arc light 2. 4. 6초와 Halogen light 20초). 그리고 광조사 방향(Vertical 방향과 Oblique 방향)을 다르게 하여 브라켓을 부착하였다. 광증합 접착제는 Transbond XT를 이용하였으며 브라켓 부착 후 5분과 24시간 후에 만능물성시험기를 이용하여 전단결합강도를 측정하였다. 결과는 다음과 같다. 광중합기의 종류와 중합시간에 관계없이 Vertical군과 Oblique군간의 전단결합강도는 유의한 차이가 없었다.(p>0.05) Plasma arc light를 이용하여 2초 동안 광중합한 군들의 전단결합강도는 다른 중합시간의 군들보다 현저히 낮았다(P<0.05). 부착 5분 후의 전단결합강도는 24시간 후보다 현저히 낮았다(P<005), ARI 점수는 군들 간에 통계적으로 유의한 차이가 없었다. 이상의 결과는 plasma arc light를 사용한 금속 브라켓의 부착시 광조사 방향은 전단결합강도에 영향을 끼치지 않으며. Halogen light와 유사한 결합강도를 얻기 위해서는 4초 이상의 중합시간이 필요함을 시사한다.