• Proceedings of the IEEK Conference
• /
• 2004.08c
• /
• pp.780-783
• /
• 2004

The two-dimensional modeling of the non-stationary thermal state and voltage responsivity of the sensitive elements usually used in solid-state pyroelectric focal plane arrays are presented. Temperature distributions under periodical thermal excitation and the response of the thermal imaging device, which is composed of the pyroelectric sensitive elements mounted on a single silicon substrate, are numerically calculated. The sensitive element consists of a covering metal layer, infrared polymer absorber, front metal contact, sensitive pyroelectric element, the interconnecting column and the bulk silicon readout. The results of the numerical modeling show that the thermal crosstalk between sensitive elements to be critical especially at low frequency (f < 10Hz) of periodically modulated light. It is also shown that the use of our models gives the possibility to improve the design, operating regimes and sensitivity of the device.

• Journal of Biomedical Engineering Research
• /
• v.14 no.1
• /
• pp.17-22
• /
• 1993

Radiation-induced fibrosarcoma tumors were grown on the flanks of C3H mice. The mice were divided intro two groups. One group was injected with Photofrin II, intravenously (2.5mg/kg body weights). The other group received no Photofrin E Mice from both groups were irradiated for approximately 15 minutes at 100,300, or $500{\;}mW/\textrm{cm}^2$ with the argon (488nm/514.5 nm), dye(628nm) and gold vapor (pulsed 628 nm) laser light. A photosensitizer behaved as an added absorber. Under our experimental conditions, the presence of Photofrin II increased surface temperature by at least 40% and the temperature rise due to $300{\;}mW/\textrm{cm}^2$ irradiation exceeded values for hyperthermia. Lights and temperature distributions with depth were estimated by a computer model. The model demonstrated the influence of wavelength on the thermal process and proved to be a valuable tool to investigate internal temperature rise.

• Macromolecular Research
• /
• v.15 no.6
• /
• pp.560-564
• /
• 2007

The photostabilization and cure kinetics of UV-curable, optical resins containing various formulations of photostabilizers were investigated to determine the system with the highest cure conversion and durability. Photo-DSC analysis revealed that increasing the concentration of a UV absorber (UVA) decreased both the crosslink density and the cure rate due to competition for the incident photons between the photoinitiator and the UVA, whereas including a hindered amine light stabilizer (HALS) hardly affected either the cure conversion or the cure rate due to its very low absorption of 365 nm. This result was confirmed by FTIR-ATR spectroscopy and UV-visible spectroscopy analyses. QUV ageing experiments showed that the cure conversion and durability were the highest for the UVA/HALS formulation at a ratio of 1 : 2, which is due to their synergistic action.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.235-236
• /
• 2008

Wet etched ZnO:Al films for thin film solar cells were prepared by Facing Target sputtering(FTS) method. Wet etching has been used to produce a rough TCO surface that enables light trapping in the absorber. The ZnO:Al films for thin film solar cells were etched by HCl 0.5%. The etching performance of ZnO:Al films can be tuned by changing etching time. The etched ZnO:Al films compared to a smooth ZnO:Al thin film structure. From the results, the lowest resistivity of deposited films was $5.67\times10^{-4}$ [$\Omega$-cm] and the transmittance of all ZnO:Al thin films were over 80% in visible range.

• Journal of the Korean institute of surface engineering
• /
• v.48 no.4
• /
• pp.169-173
• /
• 2015

$CuInSe_2$ thin films which have been widely used for thin solar cells as a light absorber were prepared by hydrazine solution processing, and their microstructural properties were investigated. Hydrazine $CuInSe_2$ precursor solutions were prepared by dissolving $Cu_2S$, S, $In_2Se_3$ and Se powder in hydrazine solvent. Multilayer $CuInSe_2$ chalcopyrite phase thin films were prepared by repeating spin-coating process using the precursor solution. Unfortunately, the presence of the interfaces between each $CuInSe_2$ layer formed by multi-layer coating impeded grain growth across the interface. Here, by doing simple interface engineering to solve the limited grain growth issue, the large grained (${\sim}1{\mu}m$) $CuInSe_2$ thin films were obtained.

• Solar Energy
• /
• v.18 no.3
• /
• pp.9-14
• /
• 1998

The present solar energy concentrator is a 2-dimensional system that incorporates with a tubular absorber. A new design theory is developed on the basis of the generalized edge-ray principle. The result shows the increase of concentration ratio for the same acceptance angle as the basic CPC by a factor of $C_{new}=C_{cpc}\{1+(d/{\pi}r)\;sin^2{\theta}_c\}$. For example, if ${\theta}_c=30^{\circ}$, the new design offers the concentration of $2.0{\sim}2.72$, whereas $C_{cpc}=2$. The new system also provide a thin and light-weight design.

• Proceedings of the KSR Conference
• /
• 2000.05a
• /
• pp.645-651
• /
• 2000

In this paper, numerically evaluated is the regulations for crashworthy design of the Korean standard urban train suggested by KRRI. The 4-car consist of K-EMU(Korean Electric Multiple Unit) train developed in recent is analyzed under various collision conditions such as normal coupling, heavy shunt, light and heavy collisions. The collision conditions are assumed as K-EMU collides against another stationary one at 5 kph, 10 kph, 25 kph and 32 kph. According to the numerical results and bibliographical study, it is necessary that the regulations by KRRI be complemented from crashworthy point of view. Furthermore, the K-EMU train is recommended to adopt a new coupler with an additional energy absorber or a mechanical fuse.

• Nuclear Engineering and Technology
• /
• v.50 no.7
• /
• pp.1024-1036
• /
• 2018

In this paper, McCARD code was verified using various models listed in the NUREG/CR-6361 benchmark guide, which provides specifications for single pin-cells, single assemblies, and the whole core classified depending on the nuclear properties and structural characteristics. McCARD code was verified by comparing its results with those of SCALE code for single pin-cell and single assembly benchmark problems. The difference in the multiplication factor obtained through the two codes did not exceed 90 pcm. The benchmark guide treats a total of 173 whole core experiments. The experiments are categorized as simple lattices, separator plates, reflecting walls, reflecting walls and separator plates, burnable absorber fuel rods, water holes, poison rods, and borated moderator. As a result of numerical simulation using McCARD, the mean value of the multiplication factors is 1.00223 and the standard deviation of the multiplication factors is 285 pcm. The difference between the multiplication factors and the experimental value is in the range of -665 pcm to + 1609 pcm. In addition, statistics of results for experiments categorized by reactor shape, additional structure, burnable poison, etc., are detailed in the main text.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.5
• /
• pp.391-399
• /
• 2011

The purpose of this paper is to predict the shock absorbing characteristics of the aluminum honeycomb in a lunar lander. Aluminum honeycomb has been used for shock absorbers of lunar lander due to its characteristics such as light weight, high energy absorption efficiency and applicability under severe space environments. Crush strength of the honeycomb should have strength to endure during shock energy absorbing process. In this paper, the crush strength, which depends on the shape of honeycomb and impact velocity, is estimated using FEM. Ls-dyna is used for finite element analysis of the honeycomb shock absorber. The unit cells of the honeycomb shape are modeled and used for the finite element analysis. Energy absorption characteristics are decided considering several conditions such as impact velocity, foil thickness and branch angle of the honeycomb.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.2
• /
• pp.37-41
• /
• 2017

Cuprous oxide ($Cu_2O$) is one of the potential candidates as an absorber layer in ultra-low-cost solar cells. $Cu_2O$ is highly desirable semiconducting oxide material for use in solar energy conversion due to its direct band gap ($E_g={\sim}2.1eV$) and high absorption coefficient that absorbs visible light of wavelength up to 650 nm. In addition, $Cu_2O$ has other several advantages such as non-toxicity, low cost and also can be prepared with simple and cheap methods on large scale. In this work, we deposited the $Cu_2O$ thin films by electrodeposition on gold coated $SiO_2/Si$ wafers. We changed the process conditions such as pH of the solution, applied potential on working electrode, and solution temperature. Finally, we confirmed the structural properties of the thin films by XRD and SEM.