• 한국산학기술학회논문지
• /
• 제15권7호
• /
• pp.4692-4697
• /
• 2014

태양광 전원은 태양광 패널이 설치된 지역의 위치와 날씨 그리고 기후 등에 매우 큰 영향을 받으며, 전원으로서의 사용시간의 제한과 출력의 불확실성이라는 특성을 갖는다. 이러한 태양광 전원의 불확실성을 가능한 줄이기 위해, 태양광 전원의 출력에 대한 오랜 기간 동안의 데이터를 분석하여 출력의 평균값을 산출해 내었다. 태양광 전원의 출력의 평균값은 태양광 전원에 직접 연결되어 그리드에 안정적인 전력을 공급하기 위한 Li 에너지 저장장치의 적정 용량산정과 운용방식에 꼭 필요한 데이터이며, 이로부터 Li 배터리의 충방전모드에 의해 그리드에 일정한 출력의 전력을 공급하는 것이 가능하도록 하였다. 태양광 전원과 Li 배터리를 포함하는 시스템이 악조건의 그리드 운전상태에서의 동작특성을 관찰하기 위해 Li 배터리의 충전율이 100%에서 10%로 단시간에 감소될 정도의 과부하 상태에 대해 태양광 전원과 Li 배터리의 운용특성을 분석하고 Li 배터리 셀 단위의 출력 및 온도특성을 해석하였다.

• 조명전기설비학회논문지
• /
• 제28권8호
• /
• pp.106-112
• /
• 2014

This paper presents the analysis of connected operation of photo voltaic source and Li energy storage system. The micro-grid has been installed and operated for several years at the campus of USF and has been a role of test bed. Photo voltaic source has been strongly influenced by the location, weather and climate of a installed area and Li battery is connected directly to the photo voltaic source to compensate for the limitations. The Li battery is operated to supply power output to the grid by the charging or discharging mode based on the average power output of the PV source which is calculated from monitored data for several years. The load of the PV and Li battery system is operated as a severe loading condition and the operating characteristics of PV source and Li battery are analyzed in detail. In connected operations of PV and Li battery to power system, the PV and Li battery is operated to supply constant power during only day time or peak time to increase load shedding ratio and efficient usage of generation sources in power system.

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.737-743
• /
• 2006

[ $Li[Co_{0.50}Li_{0.17}Mn_{0.33}]O_2$ ] powder was prepared using a simple combustion method. specially, ratio of 2:1, 3:2, 1:1, 2:3, 1:2 was adopted as acetate source/nitrate source. The diffraction pattern of $Li[Co_{0.50}Li_{0.17}Mn_{0.33}]O_2$ powder showed that this compound could be classified as hexagonal $a-NaFeO_2$ structure (space group : $R\bar{3}m$). The size of powder was less than $1{\mu}m$. Small particle size of cathode powder would give a good ionic and electronic conductivity to cathode electrode, which made of cathode powder. As the increase of nitrate source-ratio, discharge capacity of $Li[Co_{0.50}Li_{0.17}Mn_{0.33}]O_2$ at high charge-discharge rate was increased. When the ratio of acetate source/nitrate source was 1:2, discharge capacity at 10 C rate (2000 mA/g) was 180 mAh/g. It was $10{\sim}15%$ larger than that of powder, which have 2:1 as acetate source/nitrate ratio.

• 분석과학
• /
• 제5권1호
• /
• pp.57-61
• /
• 1992

중성자 스펙트럼을 측정하기 위해 $^6Li$ 중성자 분광계를 설치하고 $^{137}Cs$과 $^{207}Bi$ 점선원을 사용하여 $^6Li$ 검출관의 특성을 파악하고 $^{241}Am-Be$ 중성자 선원을 사용하여 중성자 포획피이크를 측정하였으며, $^6Li$ (n, ${\alpha}$) T 반응에 의한 에너지 파고스펙트럼을 측정하였다. 또한 중성자 선원의 조사 시간의 변화, 선원과 검출관 사이의 거리의 변화, 파고분석기의 문턱조절자를 미세하게 변환시키는 경우에 파고스펙트럼을 측정하였다.

• Journal of Electrochemical Science and Technology
• /
• 제13권3호
• /
• pp.407-415
• /
• 2022

Surface coating of cathodes is an essential process for all-solid-state batteries (ASSBs) based on sulfide electrolytes as it efficiently suppresses interfacial reactions between oxide cathodes and sulfide electrolytes. Based on computational calculations, Li₃PO₄ has been suggested as a promising coating material because of its higher stability with sulfides and its optimal ionic conductivity. However, it has hardly been applied to the coating of ASSBs due to the absence of a suitable coating process, including the selection of source material that is compatible with ASSBs. In this study, polyphosphoric acid (PPA) and (NH₄)₂HPO₄ were used as source materials for preparing a Li₃PO₄ coating for ASSBs, and the properties of the coating layer and coated cathodes were compared. The Li₃PO₄ layer fabricated using the (NH₄)₂HPO₄ source was rough and inhomogeneous, which is not suitable for the protection of the cathodes. Moreover, the water-based coating solution with the (NH₄)₂HPO₄ source can deteriorate the electrochemical performance of high-Ni cathodes that are vulnerable to water. In contrast, when an alcohol-based solvent was used, the PPA source enabled the formation of a thin and homogeneous coating layer on the cathode surface. As a consequence, the ASSBs containing the Li₃PO₄-coated cathode prepared by the PPA source exhibited significantly enhanced discharge and rate capabilities compared to ASSBs containing a pristine cathode or Li₃PO₄-coated cathode prepared by the (NH₄)₂HPO₄ source.

• 한국태양에너지학회 논문집
• /
• 제24권3호
• /
• pp.39-46
• /
• 2004

In this paper, thermodynamic design data for heating of double-effect absorption system using LiCl-water for evaporator heating source of sofar energy are investigated for the water-LiCl pair and a comparative study of the water-LiCl pair with the water-LiBr pair is given used for the computer simulation. The computer simulation is based on mass, material and heat balance equations for each part of the system. Coefficients of performance and flow ratios for effects of different operating temperatures are investigated. It is found that the heating COP is higher for the water -LiCl pair than for the water-LiBr pair, and FR is lower for the water-LiCl pair than for the water LiBr pair.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 춘계학술대회 논문집
• /
• pp.95-99
• /
• 2001

As a way to use energy effectively, the present study is aimed at investigating the performance characteristics of a Single Effect LiBr/Water Absorption Refrigerator using a low temperature driving heat-source. It was carried out by changing the driving heat-source temperature, the cold water outlet temperature(the refrigeration load), the cooling water inlet temperature, and the weak solution flow rate and this study compares the performance characteristics of refrigerator against the existence and non-existence of the Recirculation of the Weak solution which is used as a method to improve the performance of refrigerator. In case of Recirculation of the weak solution, more improved the Refrigeration Capacity and COP was obtained, and these effects became more larger in the high temperature of driving heat-source and large quantity of solution.

• Bulletin of the Korean Chemical Society
• /
• 제25권4호
• /
• pp.511-516
• /
• 2004

A Li$[Co_{0.17}Li_{0.28}Mn_{0.55}]O_2$ cathode compound was prepared by a simple combustion method. The X-ray diffraction pattern showed that this compound could be classified as ${\alpha} -NaFeO_2$ structure type with the lattice constants of a = 2.8405(9) ${\AA}$ and c = 14.228(4) ${\AA}$. According to XANES analysis, the oxidation state of Mn and Co ions in the compound were 4+ and 3+, respectively. During the first charge process, the irreversible voltage plateau at around 4.65 V was observed. The similar voltage-plateau was observed in the initial charge profile of other solid solution series between $Li_2MnO_3\;and\;LiMnO_2$ (M=Ni, Cr...). The first discharge capacity was 187 mAh/g and the second discharge capacity increased to 204 mAh/g. As the increase of cycling number, one smooth discharge profile was converted to two distinct sub-plateaus and the discharge capacity was slowly decreased. From the Co and Mn K-edge XANES spectra measured at different cyclic process, it can be concluded that irreversible transformation of phase is occurred during continuous cycling process.

• 한국전기전자재료학회논문지
• /
• 제22권7호
• /
• pp.576-579
• /
• 2009

This paper suggests a autonomous linear Li-ion battery charger which can safely distribute power between an external power source(AC adapter, auto adapter, or USB source), battery, and the system load. Depending on an external power source's capability, the charger selects proper charging-mode automatically. The charger IC designed and fabricated on Dongbu HITEC's $0.35{\mu}m$ BCD process with layers of one poly and three metals.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.27-28
• /
• 2009

This paper suggests a autonomous linear Li-ion battery charger which can safely distribute power between an external power source(AC adapter, auto adapter, or USB source), battery, and the system load. Depending on an external power source's capability, the charger selects proper charging-mode automatically. The charger IC designed and fabricated on Dongbu HITEC's $0.35{\mu}m$ BCD process with layers of one poly and three metals.