• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.2
• /
• pp.144-152
• /
• 1997

Film absorption involves simultaneous heat and mass transfer in the vapor-liquid system. In the present work, the absorption process of water vapor by an aqueous soluton of LiBr flowing inside of the vertical tube was investigated. The continuity, momentum, energy and diffusion equations for the solution film and vapor were formulated in integral forms and solved numerically. The model could predict the film thickness, the pressure gradient, and the heat and mass transfer rate. Particularly the effects of vapor flow conditions on the absorption process were investigated in terms of the vapor Reynolds number. As the vapor Reynolds number increased, the shear stress at the vapor-solution interface also increased. Consequently solution film became thinner at higher vapor flowrate under the co-currentflow condition. Thinner film was capable of higher heat transfer to the wall and leaded to higher absorption rate of the water vapor into the solution film.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.4
• /
• pp.456-465
• /
• 1998

Effect of a non-absorbable gas on the absorption process in a vertical tube absorber was investigated numerically. The water vapor mined with air as the non-absorbable gas is absorbed into LiBr/water solution film. The flow is assumed to be laminar and fully developed in both liquid and gas phases. The diffusion and energy equations were solved in both phases to give the temperature and concentrations, from which heat and mass fluxes were determined. It was shown that the local absorption rate decreases as the mass fraction of air in water vapor increases. The vapor pressure of water at the liquid-vapor interface reduces significantly since the non-absorbable gas is accumulated near the interface. The effect of non-absorbable gases on absorption rate becomes larger as the mass flow rate of the vapor decreases. For small amount of non-absorbable gases the total absorption rate of water vapor increases as the mass flow rate of the vapor decreases. Total absorption rate increases as the mass flow rate of the vapor increases for large concentration of non-absorbables at the inlet of an absorber.

• Journal of Electrochemical Science and Technology
• /
• v.5 no.2
• /
• pp.58-64
• /
• 2014

The surface of an ordered mesoporous silica (OMS) was functionalized using 1H,1H,2H,2H-perfluorooctyltrimethoxysilane at $20^{\circ}C$ and $60^{\circ}C$. It was shown that only elevated temperature allows lyophobic properties on the walls of OMS, eventually preventing pore flooding with nonaqueous electrolytes. The functionalized OMSs (OMS-F) were characterized with various techniques: wettability test, $N_2$ sorption measurement, high-resolution transmission electron microscopy (HR-TEM). Cathodes of $10mg/cm^2$ loading were prepared with a commercial Pt/C catalyst and polyvinylidene fluoride (PVDF, 2.5 wt.%) binder using a typical doctor blade method on a commercial gas diffusion layer (GDL) in the presence or in the absence of OMS-F additives. Subsequent discharge-charge curves were taken in a 1M LiTFSI-TEGDME electrolyte at 60oC in pure oxygen atmosphere. It was found that the discharge capacity was significantly affected by OMS-F: 5 wt.% of additive extended discharge capacity by a factor 1.5. On the other hand, a similar OMS material but synthesized at $20^{\circ}C$ did not show lyophobic properties and deteriorated cathode capacity.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.160.2-160.2
• /
• 2014

Recently silicon has attracted intense interest as a promising anode material of lithium-ion batteries due to its extremely high capacity of 4200 mA/g (for Li4.2Si) that is much higher than 372 mAh/g (for LiC6) of graphite. However, it seriously suffers from large volume change (even up to 300%) of the electrode upon lithiation, leading to its pulverization or mechanical failure during lithiation/delithiation processes and the rapid capacity fading. To overcome this problem, Si nanowires have been considered. Use of such Si nanowires provides their facile relaxation during lithiation/delithiation without mechanical breaking. To design better Si electrodes, a study to unveil atomic-scale mechanisms involving the volume expansion and the phase transformation upon lithiation is critical. In order to investigate the lithiation mechanism in Si nanowires, we have developed a reactive force field (ReaxFF) for Si-Li systems based on density functional theory calculations. The ReaxFF method provides a highly transferable simulation method for atomistic scale simulation on chemical reactions at the nanosecond and nanometer scale. Molecular dynamics (MD) simulations with the ReaxFF reproduces well experimental anisotropic volume expansion of Si nanowires during lithiation and diffusion behaviors of lithium atoms, indicating that it would be definitely helpful to investigate lithiation mechanism of Si electrodes and then design new Si electrodes.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.4
• /
• pp.193-197
• /
• 2011

The influences of the thickness and microstructure of Fe layer on the electrochemical performances of Fe/Si multilayer thin film anodes were investigated. The Fe/Si multilayer films were prepared by electron beam evaporation, in which Fe layer was deposited with/without simultaneous bombardment of Ar ion. The kinetics of Li insertion/extraction reactions in the early stage are slowed down with increasing the thickness of Fe layer, but such a slowdown seems to be negligible for thin Fe layers less than about $500{\AA}$. When the Fe layer was deposited with ion bombardment, even the $300{\AA}$ thick Fe layer significantly suppress Li diffusion through the Fe layer. This is attributed to the dense microstructure of Fe layer, induced by ion beam assisted deposition (IBAD). It appears that the Fe/Si multilayer films prepared with IBAD show good cyclability compared to the film deposited without IBAD.

• Journal of the Korean Ceramic Society
• /
• v.56 no.1
• /
• pp.65-70
• /
• 2019

Simple fabrication of a powdered Ge-reduced graphene oxide (Ge-rGO) composite via spray pyrolysis and reduction is introduced herein. Successful incorporation of the rGO nanosheets with Ge hindered the aggregation of Ge and conferred enhanced structural stability to the composite by alleviating the mechanical stress associated with drastic volume changes during repeated cycling. The Li-ion storage performance of Ge-rGO was compared with that of powdered Ge metal. The reversible discharge capacity of Ge-rGO at the $200^{th}$ cycle was $748mA\;h\;g^{-1}$ at a current density of $1.0A\;g^{-1}$ and Ge-rGO showed a capacity of $375mA\;h\;g^{-1}$ even at a high current density of $5.0A\;g^{-1}$. The excellent performance of Ge-rGO is attributed to the structural robustness, enhanced electrical conductivity, and formation of open channels between the rGO nanosheets, which facilitated electrolyte penetration for improved Li-ion diffusion.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.4
• /
• pp.132-138
• /
• 2023

Doped and undoped-BiVO₄ samples with different elements (Li, Mg) and amounts were synthesized with a hydrothermal method. The synthesized samples were characterized using various techniques including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV-Vis diffusion reflectance spectroscopy (UV-Vis DRS), and photoluminescence (PL) spectroscopy. Photocatalytic activity of the samples was evaluated by measuring the degradation of methyl blue (MB) under visible light irradiation. The results indicated that the incorporation of Mg and Li into BiVO₄ caused lattice distortion, the presence of surface hydroxyl groups, a narrower band gap, and a reduced recombination ratio of photo-induced electron-hole pairs. Notably, the photocatalytic activity of Mg5%-Li5% co-doped BiVO₄ sample exhibited a significant improvement compared to that of undoped BiVO₄ sample.

• Journal of Electrochemical Science and Technology
• /
• v.14 no.2
• /
• pp.139-144
• /
• 2023

In this study, carbon-coated porous nanofibers were prepared via electrospinning and the performance of Li[Ni_0.93Co_0.07]O₂ (NC) synthesized by electrospinning (E-NC) and co-precipitation (C-NC) was compared. E-NC had a discharge capacity of 206 mAh g^-1 at 0.1C (17 mA/g), which is 10% higher than that of C-NC (189.2 mAh g^-1). E-NC shows a high-rate performance of 118.32 mAh g^-1 (61.7%) at 5C (850 mA/g), which is 50% higher than that of C-NC (78.22 mAh g^-1 = 45.7%). Charge transfer of the carbon-coated porous nanofiber E-NC decreased by 35% compared to C-NC after 20 cycles as observed using electrochemical impedance spectroscopy. The results of this study show that the nanofiber structure with carbon coating shortens the Li-ion diffusion path, improves electrical conductivity, resulting in excellent rate performance.

• Journal of applied mathematics & informatics
• /
• v.18 no.1_2
• /
• pp.273-286
• /
• 2005

Parameter identification problem of a three species (predator, mutualist-prey, and mutualist) ecological system with reaction-diffusion phenomenon is investigated in this paper. The mathematical model of the parameter identification problem is constructed and continuous dependence of the solution for the direct problem on the parameters identified is obtained. Finally, the existence of optimal solution and an optimality necessary condition for the parameter identification problem are given.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.1450-1452
• /
• 2009

In this work, a plastic diffuser which has a surface similar to Sinusoidal wave profile for application of LC D backlighting is proposed. This new pattern diffuser is achieved the values of the transmission efficiency an d diffusion efficiency all over 70%, and it also has the value about gain over 1.1. Additionally, this new patter n diffuser has high uniformity when we put it in the LCD backlight module and its thickness is only 2mm. With these foregoing properties, this diffuser film can widely applied to LCD displays systems etc.