• Proceedings of the Korea Water Resources Association Conference
• /
• 2017.05a
• /
• pp.514-514
• /
• 2017

Floating breakwaters were treated as solid bodies without any perforation in previous studies. In this study, however, a floating breakwater is perforated to allow the partial absorption of the energy produced by incident waves and an air chamber is placed in the upper part to control the breakwater draft. A series of laboratory experiments for a floating breakwater installed with a mooring system are carried out. In general, a mooring system can be classified by the number of mooring points, the shape of the mooring lines, and the degree of line tension. In this study, a four-point mooring is employed since it is relatively easier to analyze the measured results. Furthermore, both the tension-leg and the catenary mooring systems have been adopted to compare the performance of the system. In laboratory experiments, the hydraulic characteristics of a floating breakwater were obtained and analyzed in detail. Also, a hydraulic model test was carried out on variable changes by changing the mooring angle and thickness of perforated wall. A hydraulic model was designed to produce wave energy by generating a vortex with the existing reflection method. Analysis on wave changes was conducted and the flow field around the floating breakwater and draft area, which have elastic behavior, was collected using the PIV system. From the test results the strong vortex was identified in the draft area of the perforated both-sides-type floating breakwater. Also, the wave control performance of the floating breakwater was improved due to the vortex produced as the tension in the mooring line decreased.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.364-370
• /
• 2008

Spinning detonations propagating in a circular tube were numerically investigated with a one-step irreversible reaction model governed by Arrhenius kinetics. The time evolution of the simulation results was utilized to reveal the propagation mechanism of single-headed spinning detonation. The track angle of soot record on the tube wall was numerically reproduced with various levels of activation energy, and the simulated unique angle was the same as that of the previous reports. The maximum pressure histories of the shock front on the tube wall showed stable and unstable pitch modes for the lower and higher activation energies, respectively. The shock front shapes and the pressure profiles on the tube wall clarified the mechanisms of two modes. The maximum pressure history in the stable pitch remained nearly constant, and the single Mach leg existing on the shock front rotated at a constant speed. The high and low frequency pressure oscillations appeared in the unstable pitch due to the generation and decay of complex Mach interaction on the shock front shape. The high frequency oscillation was self-induced because the intensity of the transverse wave was changed during propagation in one cycle. The high frequency behavior was not always the same for each cycle, and therefore the low frequency oscillation was also induced in the pressure history.

• Journal of radiological science and technology
• /
• v.42 no.3
• /
• pp.195-199
• /
• 2019

Most of the vascular procedures performed for various diagnoses and treatments of various abdominal intervention procedures performed by the Department of Radiology and Angiography are performed by puncture of the femoral artery. For this reason, patients should undergo blood-related tests such as prothrombin time (PT) and partial thromboplatin time (PTT). Therefore, many patients are instructed to take precautions such as putting a sandbag on the puncture site to prevent delayed hemorrhage after hemostasis of the femoral artery puncture site, and not to bend the leg of the treated area for about 3 hours. Because of this, many patients have complained of pain during the procedure and inconvenience during the absolute bed rest time in the ward. The purpose of this study was to compare the safety of balloon ancillary devices with sandbags placed on the hemostasis site to prevent delayed hemorrhage after arterial puncture. We compared the safety of each patient with the results of medical records in consideration of the problem that the patient could not press with the focus, the position of the patient was changed depending on the patient's body shape, and the problem of falling down according to the location of the puncture site. As a result, the use of a balloon type ancillary device improves the effect of continuous hemostasis, reduces discomfort during the patient's absolute stabilization time, increases the patient's satisfaction, and is a good alternative to the existing sandbag.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.429-434
• /
• 1996

K-REM［1］, which is under development as a realistic evaluation model of large break LOCA, is applied to the analysis of cold leg guillotine break of Ulchin 3&4. Fuel parameters on which statistical analysis of their effects on the peak cladding temperature (PCT) are made and system parameters on which the concept of limiting value approach (LVA) are applied, are determined from the single parameter sensitivity study. 3 parameters of fuel gap conductance, fuel thermal conductivity and power peaking factor are selected as fuel related ones and 4 parameters of axial power shape, reactor power, decay heat and the gas pressure of safety injection tank (SIT) are selected as plant system related ones. Response surface of PCT is generated from the plant calculation results and on which Monte Carlo sampling is made to get plant application uncertainty which is statistically combined with code uncertainty to produce the 95th percentile PCT. From the break spectrum analysis, blowdown PCT of 1350.23 K and reflood PCT of 1195.56 K are obtained for break discharge coefficients of 0.8 and 0.5, respectively.

• Journal of Naturopathy
• /
• v.8 no.2
• /
• pp.63-70
• /
• 2019

Purpose: The purpose of this study was to investigate whether Qihyul-therapy was effective against subjects of bad Qihyul circulation who had narrowed muscles of the buttocks, a distorted body shape, or pain. Methods: Qihyul-therapy used. Results: The muscles of the buttocks remained almost untouched. The elasticity of the muscles restored. The skin tone brightened, and the anal muscle strengthened after Qihyul-therapy. The subject's body was shifted to the right by -7°. The right arm was about 6 cm longer than the left arm. But after correction, the right arm was about 5 cm shorter. The distorted body was almost balanced. After neck and shoulder correction, the distance between the collarbone and neck was 7~10 cm wider. After the pelvic correction, the pain in the buttocks was relieved, and the position of the hip joint returned correctly. The right leg that was turned 45° to the left was corrected, and the length became the same. Subjects had no knees attached, their right knees were up 5 cm above the left, and their ankles bent at an angle of 30 ° relative to the left, but after correction, the knees of the two legs stably attached. The height of the knee became the normal angle. Conclusion: If the Qihyul-therapy, the spine correction Qihyul-exercise and the pelvic correction Qihyul-exercise performed steadily, the deformed body shape restored adequately, and it is useful to prevent and cure related diseases by alleviating the pains.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.1
• /
• pp.141-152
• /
• 2022

As interest increases related to the development of eco-friendly energy, the offshore wind turbine market is growing at an increasing rate every year. In line with this, the demand for an installation vessel with large scaled capacity is also increasing rapidly. The wind turbine installation vessel (WTIV) is a fixed penetration of the spudcan in the sea-bed to install the wind turbine. At this time, a review of the spudcan is an important issue regarding structural safety in the entire structure system. In the study, we analyzed the current procedure suggested by classification of societies and new procedures reflect the new loading scenarios based on reasonable operating conditions; which is also verified through FE-analysis. The current procedure shows that the maximum stress is less than the allowable criteria because it does not consider the effect of the sea-bed slope, the leg bending moment, and the spudcan shape. However, results of some load conditions as defined by the new procedure confirm that it is necessary to reinforce the structure to required levels under actual pre-load conditions. Therefore, the new procedure considers additional actual operating conditions and the possible problems were verified through detailed FE-analysis.

• Journal of Korean Medicine Rehabilitation
• /
• v.32 no.3
• /
• pp.1-11
• /
• 2022

Objectives This study was designed to evaluate the healing effect of Cordyceps Militaris (CM) on collagen II-induced arthritis rats. Methods Sprague-Dawley rats were randomly divided into 6 groups (normal, control, positive control, CM with low/medium/high dosage each). Type II collagen mixed with complete Freund's adjuvant (with 1:1 v/v) was injected subcutaneously, and the mixture was injected in a same manner one week after the first injection to boost arthritis. Arthritis index, paw thickness and von Frey test were conducted to observe physical changes. hematoxylin and eosin (H&E) staining was performed to observe knee cartilage. The levels of messenger RNA (mRNA) expressions of interleukin (IL)-1𝛽, IL-6, tumor necrosis factor-alpha (TNF-𝛼) in spleen were assessed by real-time polymerase chain reaction. Results Rheumatoid arthritis is an autoimmune disease that occurs on multiple joints and can lead to temporary shape change of bones or organ failure in severe cases. Here, we aimed to determine the effect of CM extract on rheumatoid arthritis by measuring paw thickness, arthritis index, conducting von Frey test and H&E staining, and evaluating the level of IL-1𝛽, IL-6, TNF-𝛼. As a result, paw thickness, arthritis index significantly decreased in low concentration group, hind leg became less sensitive in all expermental groups. Also, histological analysis showed that the damage of knee cartilage was prevented in all experimental groups. The level of mRNA of IL-1𝛽, IL-6, and TNF-𝛼 in spleen was analyzed to decide the effectiveness of CM extract. IL-1𝛽 did not show significant change, but IL-6 and TNF-𝛼 showed significant decrease in at least one of the experimental groups. Conclusions CM showed protective effect on knee tissue destruction and improved the physical conditions of the leg involving arthritis. Also, it showed that CM has anti-inflammatory effect on specific cytokines inducing rheumatoid arthritis. In conclusion, this study demonstrated that the therapeutic potential of CM for the treatment rheumatoid arthritis, and set the foundation for the further studies.

• The Research Journal of the Costume Culture
• /
• v.19 no.6
• /
• pp.1150-1162
• /
• 2011

Considering the fact that the fit for men's clothes is important for the sizing system modern ready-made pants, an analysis of obese middle-aged men is required at this period of time to determine the appropriate fit for obese men. The following research focused on 635 middle-aged obese men who had a BMI index of at least 25 and a waist circumference from the belly-button level of 34 inches or more. This research deals with the articles of circumference, thickness and other major physical changes that happen during the 30s, 40s, and 50s. According to the analysis of these body measurement articles with specific regard to age, men's height and the height of their waist seemed to decrease as their age increased. This demonstrates that as these men grow older, the waist and stomach slowly curved into a circular and flat body type due to their obesity. In this study, the first factor figure was the height and leg length. The second factor figure was the waist form. The third factor figure was the center thigh circumference. The fourth and fifth factor figures were the hip length and shape. Lastly, the sixth factor figure was the calf circumference. These 6 factor figures construct 80.57% of the volume explanation and showed 3 patterns through a cluster analysis that showed different patterns of obesity forms for waist circumferences in key figure 1, waist and thigh circumferences in key figure 2, and waist and buttocks circumferences. Therefore, it was worthwhile to consider the circumferences of the waist, buttocks and thigh according to the body type category to enhance the drafting of well-fitting pants.

• The Korean Fashion and Textile Research Journal
• /
• v.20 no.3
• /
• pp.343-352
• /
• 2018

The objective of this study is to investigate the market of fitness compression wear as well as to design an optimal fitness compression wear by analyzing the muscle and movement characteristics of the elderly women in Korea. In this regard, research for functional garments is needed to increase muscle activity of elderly people during physical exercise. Firstly, we investigated the brand, design, size, material, and pattern of fitness wear based on the market survey. Secondly, we identified preference, evaluation items, evaluation method, and pattern design method based on the literature review. Finally, in addition, the motion type, range, angle to improve the muscle strength of the elderly were investigated and the maximum muscle strengths of each motion were analyzed by using 2007 Size Korea data (n = 386). It is also designed for muscle fatigue through exercise and rapid fatigue recovery after exercise. The evaluation methods for fitness compression wear were classified as motor functionality, physiological comfort, pattern and material suitability evaluations. The muscle strength at leg (pushing force) and waist (lifting force) of the ages of 60 to 69 years old showed 239.3 N and 274.5 N, respectively, which were the lowest forces compared to younger age groups. By applying these results to the design process of fitness wear, it is anticipated that the fitness wear will have a proper fit to the body shape of elderly people in South Korea as well as it can increase muscle efficiency to promote physical capability and healthy life for senior people.

• Korean Journal of Applied Biomechanics
• /
• v.18 no.1
• /
• pp.147-158
• /
• 2008

The purpose of this study was to analyze the kinematical variables involved in two types of service motion in tennis pinpoint and platform stance, to find the fastest serving method. Seven skilled high school tennis players participated, and the kinematics were recorded by the Vicon motion analysis system. For the gathering and analysis of the data workstation, bodybuilder and polygon were used. During the back swing for the pinpoint stance, as the back leg moves forward the COM and the racquet moves more, thus taking 0.04 seconds longer than the platform stance. The body of the subject takes a bow-shape as the subject's foot moves back and their hip moves forward. This movement enables the subject to create more power during the backswing to impact. It also increases the spread of the COM racquet and the serve speed is increase. As there is no forward movement of the foot during the backswing of the platform stance, the COM and the racquet move less and thus the time required is shorter than that for the pinpoint stance by 0.04seconds. Similarly, the time spent creating the power for the serve is shortened, the COM racquet is narrower and the speed is lessened. However, the advantage of this serve is that it increases the stability.