• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.213-214
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.645-649
• /
• 1997

In case of swash plate type axial piston hydraulic motor, hydrostatic bearing used to achieve the lubrication effect on the mechanical sliding contact areas between the following parirs ; sliooer-pad and swash plate,piston and cylinder bore,valve plate and cylinder block, etc. This study discussed the basic charateristic for the hydrostatic slipper-pad bearings with the capillary or orifice restrictor under static load condition. And, we also development of hydrostatic bearing tester for hydrostatic balancing test of pistion & slipper-pad assembly, and some experimental data on supply pressure step responce are reported.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.111-111
• /
• 2000

In order to form a uniform oxidation layer and spinel crystalline phase that has been help strong bonding in Kovar(Fe-29Ni-17Co)-to-glass sealing, the humidified nitrogen and nirtogen/hydrogen mixture was used as an oxidation atmosphere. Kovar oxidation was diffusion-controlled reaction and the activation energy was 25~32 kcal/mol at $600~900^{\circ}C.$ After oxidation at $600^{\circ}C, $ the oxidation layer was under 1 $\mu\textrm{m}$ thickness and crystalline phase was spinel which was found to be suitable for the Kovar-to-glass sealing. The Kovar-to-glass seal was carried out at $1010^{\circ}C$ and humidified nitrogen/hydrogen mixture atmosphere. Sealing properties were tested by Leak tester and SEM.

• Phonetics and Speech Sciences
• /
• v.7 no.4
• /
• pp.93-99
• /
• 2015

In case of PAS test, the air is sometimes leaked although the mask is tightly attached to the face, which is not reliable on the measured values. Therefore, this study aimed to assist the clinical practice suggesting the test method of PAS without air leakage. In the healthy subjects with 12 males and 12 females over 19 years old, three types of tests were performed on the voicing efficiency among the protocol of PAS Model 6600. They are; first, to attach the mask tightly to the face holding the handle of PAS with the subject's two hands (Method 1); second, to attach the mask tightly to the face holding the handle of PAS with the subject's one hand and pushing the body of PAS strongly with the other hand (Method 2); and third, to attach the mask tightly to the face pushing the upper part of the mask by the tester when the subject attached the mask to his or her face holding the handle of PAS with two hands (Method 3). Upon the study analyses, the mean negative pressure, the mean phonogram, subglottic air pressure, and voicing efficiency were shown to be statistically significantly different during PAS test in males depending on the methods. (p<.05) In case of females, only the target airflow rate showed significant difference depending on the methods during PAS test. (p<.001) In conclusion, Method 2 enhanced the noise level and strength while Method 1 was likely to leak the air more compared to the other two methods in males. In case of females, Method 1 showed significant leakage of the air flow. Not to allow the air flow leakage without affecting the outcome of PAS test, it will be the most useful for the tester to push the mask to the subject's face tightly (Method 3).

• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.114-118
• /
• 2014

This paper presents improvement of the production process of a unified fuel heater with the help of the performance evaluation system. In order to enhance a starting capability of diesel-engine car, the unified fuel heater is proposed, which consists of main body, upper plate, stopper, lower plate, PTC, screw, bimetal and terminals. In the proposed heater, the sensor is combined with heater body not only to maximize the performance of car but also to reduce the production cost. The performance test chamber is proposed to evaluate the performance of heater. Especially, an effective manufacturing progress for assembling the heater elements can cut down expenses.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.252-252
• /
• 2010

적외선 센서는 빛의 유무에 관계없이 주 야간 전방의 물체에서 발산하는 미약한 적외선(열선)을 감지하여 영상으로 재현하는 열상시스템은 자동차 야간 운전자 보조용 나이트 비젼, 핵심 시설의 감시 관리, 군수 등의 분야에 적용되어지고 있는 최첨단, 고부가가치를 지니고 있는 기술이다. 양자형은 센서 특성은 좋으나 냉각기(작동온도: $-196^{\circ}C$) 및 고진공 패키지인 dewar를 사용하는 반면에, 열형은 대부분 상온에서 동작되는 온도안정화를 위한 전자냉각모듈만을 구비하면 되므로 저가형으로 제작이 가능한 비냉각형 적외선 센서이다. 본 연구에서는 적외선 센서용 진공패키지 조립공정 및 패키지된 센서의 측정기술을 개발하였다. 금속 메탈패키지를 제작하였으며, 금속 진공패키지는 소자냉각용 TE Cooler와 장수명 진공유지를 위한 getter, 그리고 센서칩, 온도센서를. 장착하여 칩을 조립하였다. Cap ass'y와 base envelop의 솔더링 공정을 수행하였으며, 진공패키지의 진공유지를 위해 TMP를 이용하여 진공을 유지하고, 약 5일동안 패키지 bake-out을 수행하였다. 진공압력은 $10^{-7}\;torr$ 이하를 유지하였으며, getter를 활성화시키고, pinch-off 공정으로 조립 ass'y를 완성하였다. 진공 패키지의 기밀성은 He leak tester를 이용하여 측정하였으며, ${\sim}10^{-9}\;std.cm^3/sec$로 기밀성을 유지하였다. TE cooler를 작동한 온도안정성은 0.05 K 이하였다. 볼로미터 센서의 반응도는 $10^2\;V/W$ 이상을 나타내었으며, 탐지도는 $2{\times}10^8cm-Hz^{1/2}/W$를 나타내었다. 본 연구를 통하여 얻어진 결과는 향후 2차원 열영상용 어레이 검출기 및 웨이퍼수준의 패키징 공정에 유용하게 응용될 것으로 판단된다.