• 한국소음진동공학회논문집
• /
• 제16권8호
• /
• pp.848-856
• /
• 2006

This paper describes the aeroelastic stability test of the small-scaled 'Next-generation Blade(NRSB)' with NRSH (next-generation hub system) and HCTH hingeless hub system in hover and forward flight conditions. Excitation tests of rotor system installed in GSRTS (general small-scale rotor test system) at KARI (Korea Aerospace Research Institute) were carried out to get lead-lag damping ratio of blades with flexures as hub flexure. MBA(moving block analysis) technique was used for the estimation of lead-lag damping ratio. First, NRSB-1F blades with HCTH hub system, then NRSB- 1F with NRSH hub system were tested. Second, NRSB-2F blades with NRSH hub system were tested. Tests were done on the ground and in the wind tunnel according to the test conditions of hover and forward flight, respectively. Non-rotating natural frequencies, non-rotating damping ratios and rotating natural frequencies were showed similar level for each cases. Estimated damping ratios of NRSB-1F, NRSB-2F with HCTH and NRSH were above 0.5%, and damping ratio increased by collective pitch angle increasement. Furthermore damping ratios of NRSB-2F were higher than damping ratios of NRSB-1F in high Pitch angle. It was confirmed that the blade design for noise reduction would give observable improvement in aeroelastic stability compared to paddle blade and NRSB-1F design.

• 조명전기설비학회논문지
• /
• 제23권12호
• /
• pp.146-153
• /
• 2009

최근 대형 건축물들은 접지그리드를 기반으로 한 공통접지방식을 채택하고 있다. 이러한 접지시스템의 성능평가는 접지저항만으로 불충분하므로 접지임피던스의 측정이 요구된다. 대형 접지시스템의 접지임피던스에 대한 측정 방법은 IEEE standard 81.2에 기술되었으나 세부적인 평가방법들은 제시되지 못한 상태이다. 본 논문은 15[m]$\times$15[m] 접지그리드에 대하여 수정된 전위강하법에 기반한 접지임피던스의 정확한 측정방법과 보조전극의 위치에 따른 도전유도 및 전자유도에 의한 측정오차를 기술한다. 그 결과 도전유도에 의한 오차는 보조전극의 거리가 늘어날수록 감소하였다. 전자유도에 의한 오차를 배제하기 위해서 전위측정선은 전류측정선과 90도를 이루어야 한다. 전위측정선과 전류측정선이 예각 또는 둔각을 이루었을 때 전자유도전압은 각각 + 또는 -를 나타내었다. 일반적으로 전자유도에 의한 오차는 예각에 비해서 둔각의 경로가 작게 나타났다.

• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.825-835
• /
• 2003

Previous studies have demonstrated the importance of joint angle errors mainly due to skin artifact and measurement errors during gait analysis. Joint angle errors lead to unreliable kinematics and kinetic analyses in the investigation of human motion. The purpose of this paper is to present the Joint Averaging Coordinate System (JACS) method for human gait analysis. The JACS method is based on the concept of statistical data reduction of anatomically referenced marker data. Since markers are not attached to rigid bodies, different marker combinations lead to slightly different predictions of joint angles. These different combinations can be averaged in order to provide a "best" estimate of joint angle. Results of a gait analysis are presented using clinically meaningful terminology to provide better communication with clinical personal. In order to verify the developed JACS method, a simple three-dimensional knee joint contact model was developed, employing an absolute coordinate system without using any kinematics constraint in which thigh and shank segments can be derived independently. In the experimental data recovery, the separation and penetration distance of the knee joint is supposed to be zero during one gait cycle if there are no errors in the experimental data. Using the JACS method, the separation and penetration error was reduced compared to well-developed existing methods such as ACRS and Spoor & Veldpaus method. The separation and penetration distance ranged up to 15 mm and 12 mm using the Spoor & Veldpaus and ACRS method, respectively, compared to 9 mm using JACS method. Statistical methods like the JACS can be applied in conjunction with existing techniques that reduce systematic errors in marker location, leading to an improved assessment of human gait.

• Structural Engineering and Mechanics
• /
• 제53권5호
• /
• pp.957-979
• /
• 2015

The present paper investigates the influence of the orientation of the ground-motion reference axes, the seismic incident angle and the seismic intensity level on the inelastic response of asymmetric reinforced concrete buildings. A single storey asymmetric building is analyzed by nonlinear dynamic analyses under twenty bi-directional ground motions. The analyses are performed for many angles of incidence and four seismic intensity levels. Moreover three different pairs of the horizontal accelerograms corresponding to the input seismic motion are considered: a) the recorded accelerograms, b) the corresponding uncorrelated accelerograms, and c) the completely correlated accelerograms. The nonlinear response is evaluated by the overall structural damage index. The results of this study demonstrate that the inelastic seismic response depends on the orientation of the ground-motion reference axes, since the three individual pairs of accelerograms corresponding to the same ground motion (recorded, uncorrelated and completely correlated) can cause different structural damage level for the same incident angle. Furthermore, the use of the recorded accelerograms as seismic input does not always lead to the critical case of study. It is also shown that there is not a particular seismic incident angle or range of angles that leads to the maximum values of damage index regardless of the seismic intensity level or the ground-motion reference axes.

• 대한정형도수물리치료학회지
• /
• 제19권2호
• /
• pp.1-9
• /
• 2013

Background: The purpose of this study is to analysis of correlation upper body according to forward head posture. Methods: The subjects of this study were 40 female university students who were equally and randomly allocated to a forward head posture group, normal group. Using general posture system, electromyograph, visual analogue scale, tape measurement, neck disability index were evaluated. Results: There was positive correlation between posture analysis and Sternocleidomastoid, neck flexion (p<.05). There was positive correlation between Craniovertebral angle (CVA) and trapezius upper, VAS (p<.05). There was negative correlation between posture analysis and CVA (p<.05). There was negative correlation between Cranial rotation angle and CVA (p<.05). Conclusion: Increased forward head posture lead to increase of pain, muscles activity, so it suggests to be necessary on the prevention of dysfunction and limited activities daily living.

• 천문학회보
• /
• 제43권1호
• /
• pp.72.2-72.2
• /
• 2018

The Opposition Effect (OE) is an enhancement of the brightness of a reflecting light as the phase angle (the Sun-target-observer angle) approaches zero. The mechanisms have been studied both theoretically and experimentally and nowadays recognized that there are two major mechanisms, namely, coherent backscattering OE (CBOE) and shadow hiding OE (SHOE). From data analyses of an S-type asteroid Itokawa taken with the Hayabusa spacecraft onboard camera, it is suggested that the CBOE would be dominant at phase angle smaller than ~ 1.4 deg, while SHOE dominates at larger phase angles (M. Lee & M. Ishiguro, under review). The study on the physical parameters which affect the OE, such as size and composition, will lead us to find a way to disentangle each of them from observation. The experiments in lab, however, faces two major difficulties: (a) the detector blocks the incident light if phase angle is nearly zero and (b) incident and emission angles must be controlled with high angular resolution to prevent blurring of OEs at different phase angles in one measurement. In this presentation, we introduce a new apparatus which has been installed at Seoul National University to investigate the OE in our lab, and summarize the initial results. It will be a valuable starting point to establish infrastructure in Korea, and will shed light on the investigation of OE physics using laboratory simulants.

• 터널과지하공간
• /
• 제5권2호
• /
• pp.104-113
• /
• 1995

Shear strength of the discontinuity on which the pre-failure of rock slope was occurred during surface excavation was measured through the direct shear test using core samples obtained in-situ. Internal friction angle was increased as the roughness of discontinuity surface(JRC) was increased. Results of the tilt test using core samples of higher JRC also showed very similar trend as those of the direct shear test. When the samples replicated from natural cores were used int he tilt test, results of friction angles showed almost perfect continuation of the residual friction angles from the direct shear test. However, when the gouge material existed in the discontinuity the internal friction angle strongly depended upon the rate of filling thickness to the height of asperity irrespective of the JRC. Based on the results of both direct shear test and tilt test internal friction angle and cohesion of discontinuity, which reflect the in-situ conditions fo pre-sliding failure and also can be used for the optimum design of support system, were assessed. Two kinds of support measures which were expected to increase the stability of rock slope were considered; lowering of slope face angle and installation of rock cable. But, it was found that the first method might lead to more unstable conditions of rock slope when the cohesion of discontinuity plane was negligibly low and in that case the support systems of any kind which could exert actual resisting force were needed to ensure the permanent stability of rock slope.

• 대한치과교정학회지
• /
• 제18권1호
• /
• pp.175-188
• /
• 1988

The purposes of the present study were to describe the vortical and anteroposterior facial dysplasia, and to identify morphologic differences associated with various facial patterns. Anteroposterior dysplasia was classified by traditional Angle's malocclusion classification and according to vertical relationships based on the SN-MP angle, facial pattern was subclassified to 3 vertical groups in each malocclusion group. Each vertical group composed of 20 samples and total 180 samples aged from 9 to 14 years. The results were as follows; 1. The skeletal differences that lead to disportionate lower facial height in vortical and anteroposterior facial dysplasia were closely related to mandibular morphology. 2. Hyperdivergent group, compared with hypodivergent group, demonstrated decrease of SNA and SNB and linguoversion of maxillary and mandibular central incisors in all malocclusion groups. 3. Irrespective of rotation of the jaws, Wits appraisal was a useful measurement in evaluation of relative anteroposterior relationship of maxilla and mandible. 4. As SN-MP angle increased, anterior facial height, especially lower anterior facial height, demonstrated significant increase and intermaxillary space also tended to increase. 5. The correlation coefficients of SN-MP angle and PTFH/ATFH demonstrated the highest value in all malocclusion groups.

• 한국전문물리치료학회지
• /
• 제28권2호
• /
• pp.117-122
• /
• 2021

Background: Flat-back posture refers to a posture in which the pelvis is tilted backward, the lumbar spine is bent, the upper thoracic spine is increasingly bent, and the lower thoracic spine is straight. Given that most of the day is spent sitting, we need to develop exercise programs and devices that are suitable for people who spend less time exercising than sitting. Objects: This study investigated the effects of resistance footrest exercise on spine posture angles in visual display terminal (VDT) workers with flat back. Methods: We measured the upper lumbar angle (ULA) and lower lumbar angle (LLA) using a flexible ruler for the ULA and LLA. Then, after 1 week of resistance footrest exercise designed to strengthen the lumbar spine musculature, we measured these angles again. We measured each angle three times and then compared measurements from before and after exercise. Results: There were no significant differences in the ULA following the strengthening exercise, but significant differences were observed in LLA. Conclusion: The resistance footrest exercise strengthened the muscles affecting the pelvic and lumbar lordotic angles, and increases in the LLA were changed. This suggests that the role of the lower lumbar spine in the lumbar lordotic curve is greater than that of the upper lumbar spine. In addition, considering the contemporary tendency to lead fairly sedentary lives, these results indicate that exercising while seated can be effective.

• 한국분무공학회지
• /
• 제29권1호
• /
• pp.32-37
• /
• 2024

Macroscopic visualization of non-evaporating sprays was experimentally conducted to investigate spray tip penetration and spray angle under low-density conditions, corresponding to an early injection strategy. Furthermore, injectors with varying injection angles (146° and 70°) and numbers of holes (8 and 14) were employed to examine the impact of injector configuration. Compared to the baseline injector, 8H146, which has 8 holes and a 146° injection angle, the spray tip penetration of the 8H70 injector was found to be longer. This can be attributed to higher momentum due to a smooth flow field between the sac volume and the nozzle inlet, which is located closer to the injector tip centerline. The increase in velocity led to intense turbulence generation, resulting in a wider spray angle. Conversely, the spray tip penetration of the 14H70 injector was shorter than that of the 8H70 injector. The competition between increased velocity and decreased nozzle diameter influenced the spray tip penetration for the 14H70 injector; the increase in momentum, previously observed for the 8H70 injector, contributed to an increase in spray tip penetration, but a decrease in nozzle diameter could lead to a reduction in spray tip penetration. The spray angle for the 14H70 injector was similar to that of the 8H146 injector. Moreover, injection rate measurements revealed that the slope for a narrow injection angle (70°) was steeper than that for a wider injection angle during the injection event.