• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.913-922
• /
• 2009

Fourteen model pile load tests using a calibration chamber and instrumented model pile were preformed to investigate the variation of the behaviors of driven piles in sands with soil and lateral cyclic loading conditions. Results of the model tests showed that the first loading cycle generated more than 70% of the pile head rotation developed for 50 lateral loading cycles. Lateral cyclic loading also made an increase of the ultimate lateral load capacity of piles for $K_0$=0.4 and an decrease for $K_0$ higher than 0.4. Higher portion of the increase or decrease in the ultimate lateral load capacity by lateral cyclic loading was generated for the first loading cycle due to densification of loosening of the soil around the pile by lateral cyclic loading. It was also observed that a two-way cyclic loading caused higher ultimate lateral load capacity of driven piles than a one-way cyclic loading. When the pile was in the ultimate state, the maximum bending moment developed in the pile increased with increasing $K_0$ value of soil and was insensitive to the magnitude and number of lateral cyclic loading.

• Steel and Composite Structures
• /
• 제1권2호
• /
• pp.201-212
• /
• 2001

In order to investigate the effect of the loading rate on the mechanical behavior of SRC shearwalls, we conducted the lateral loading tests on the 1/3 scale model shearwalls whose edge columns were reinforced by H-shaped steel. The specimens were subjected to the reversed cyclic lateral load under a variable axial load. The two types of loading rate, 0.01 cm/sec for the static loading and 1 cm/sec for the dynamic loading were adopted. The failure mode in all specimens was the sliding shear of the in-filled wall panel. The edge columns did not fail in shear. The initial lateral stiffness and lateral load carrying capacity of the shearwalls subjected to the dynamic loading were about 10% larger than those subjected to the static loading. The effects of the arrangement of the H-shaped steel on the lateral load carrying capacity and the lateral load-displacement hysteresis response were not significant.

• 한국지반공학회논문집
• /
• 제27권3호
• /
• pp.63-73
• /
• 2011

반복수평하중을 받는 말뚝의 거동은 반복하중의 크기와 재하횟수 뿐만 아니라 반복하중의 재하방법(한방향 또는 양방향 재하)에도 영향을 받는다. 본 연구에서는 반복수평하중의 재하방법이 모래지반에 타입된 항타말뚝의 거동에 미치는 영향을 조사하기 위해서 가압토조를 이용한 모형말뚝재하시험을 수행하였다. 실험결과에 따르면 반복수평하중을 한방향으로 받는 말뚝의 누적 영구수평변위는 최초 재하방향과 같은 방향으로 발생하지만, 반복하중을 양방향으로 받는 말뚝의 영구수평변위는 최초 재하방향과 반대 방향으로 발생하였다. 그리고 이와 같은 반복하중의 재하방법에 따른 말뚝 영구수평변위의 변화로 인해 한방향 반복재하는 말뚝의 반복극한수평지지력을 감소시키고 양방향 반복 재하는 말뚝의 반복극한수평지지력을 증가시켰으며, 수평하중의 반복재하횟수가 많아질수록 하중의 재하방법에 따른 말뚝의 반복극한수평지지력 차이는 더욱 확대되었다. 또한 반복수평하중의 재하방법에 따른 말뚝 주변지반의 다짐도 차이로 인해 수평하중이 반복재하되는 동안 말뚝에 발생하는 최대 휨모멘트는 반복하중이 양방향보다 한방향으로 재하되는 경우에 더 크게 나타났다. 그러나 극한상태에서 말뚝에 발생한 최대 휨모멘트는 반복하중이 한방향보다 양방향으로 재하된 경우에 그리고 반복재하를 받은 경우보다 그렇지 않은 경우에 더 큰 것으로 조사되었다.

• 한국지진공학회논문집
• /
• 제1권2호
• /
• pp.31-37
• /
• 1997

삼국시대 이후 근대까지 민가의 가장 보편적인 형태였던 초가삼가의 평균적인 상세 구조를 제시하였다. 목조 프레임이 주로 사용되었으며 프레임의 조인트는 사개맞춤이 일반적이었다. 초가삼간을 구성하는 평주 및 고주 프레임의 정적 수평내력을 1:1 실험모델을 통하여 평가하였다. 기둥 상부 조인트의 형태 및 심벽이 수평내력에 미치는 영향과 조인트의 파괴모드를 분석하였다. 실험결과 평주 프레임의 극한 수평내력은 1,090N, 파괴시 최대 수평변위는 400mm(1/6 rad)이었다. 고주 프레임의 경우 이들 값은 각각 4,160 N 및 250 mm(1/9.6 rad)이었다. 프레임의 거동은 모두 조인트의 거동에 지배되었으며 매우 큰 비선형을 보였다. 조인트의 파괴모드는 평주 프레임의 경우 화통가지의 전단파괴, 고주프레임의 경우 화통가지의 휨파괴가 주요한 모드였다.

• Structural Engineering and Mechanics
• /
• 제49권2호
• /
• pp.147-161
• /
• 2014

In this paper a nonlinear finite element analysis model is established for cold-formed steel zed-section purlins subjected to uplift loading. In the model, the lateral and rotational restraints provided by the sheeting to the purlin are simplified as a lateral rigid restraint imposed at the upper flange-web junction and a rotational spring restraint applied at the mid of the upper flange where the sheeting is fixed. The analyses are performed by considering both geometrical and material nonlinearities. The influences of the rotational spring stiffness and initial geometrical imperfections on the uplift loading capacity of the purlin are investigated numerically. It is found that the rotational spring stiffness has significant influence on the purlin performance. However, the influence of the initial geometric imperfections on the purlin performance is found only in purlins of medium or long length with no or low rotational spring stiffness.

• Earthquakes and Structures
• /
• 제18권5호
• /
• pp.581-598
• /
• 2020

This paper aims to investigate the seismic behavior and influence parameters of the large-scaled thin-walled reinforced concrete (RC) tubular columns in air-cooled supporting structures of thermal power plants (TPPs). Cyclic loading tests and finite element analysis were performed on 1/8-scaled specimens considering the influence of wall diameter ratio, axial compression ratio, longitudinal reinforcement ratio, stirrup reinforcement ratio and adding steel diagonal braces (SDBs). The research results showed that the cracks mainly occurred on the lower half part of RC tubular columns during the cyclic loading test; the specimen with the minimum wall diameter ratio presented the earlier cracking and had the most cracks; the failure mode of RC tubular columns was large bias compression failure; increasing the axial compression ratio could increase the lateral bearing capacity and energy dissipation capacity, but also weaken the ductility and aggravate the lateral stiffness deterioration; increasing the longitudinal reinforcement ratio could efficiently enhance the seismic behavior; increasing the stirrup reinforcement ratio was favorable to the ductility; RC tubular columns with SDBs had a much higher bearing capacity and lateral stiffness than those without SDBs, and with the decrease of the angle between columns and SDBs, both bearing capacity and lateral stiffness increased significantly.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 추계 학술발표회 논문집
• /
• pp.77-80
• /
• 2006

Longitudinal reinforcements of the plastic hinge region were behaved tensile deformation and compressional deformation by direction of lateral loading. However Confinement steels were behaved only tensile deformation by lateral loading. Transverse steels were laid the state of tension in the lateral loading of time, and they were laid state that stress is zero when it was removed lateral load. Nine specimens were tested under cyclic stresses(tension and zero). The purpose of this research is to investigate the strain behavior and capacity of energy for confinement steel. The selected test variables are $L/d_b(L/d_b=6)$, size of reinforcement and specified yielding strength(300, 400, 500 MPa).

• Earthquakes and Structures
• /
• 제14권1호
• /
• pp.11-20
• /
• 2018

Three-dimensional panels are one of the modern construction systems which can be placed in the category of industrial buildings. There have always been a lot of studies and efforts to identify the behavior of these panels and improve their capacity due to their earthquake resistance and high speed of performance. This study will provide a comparative evaluation of behavior of updated three-dimensional panel's structural components under lateral load in both independent and dependent modes. In fact, this study tries to simultaneously evaluate strengthening effect of three-dimensional panels and the effects of system state (independent, L-shaped and BOX shaped Walls) with reinforcement armatures with different angles on the three-dimensional panels. Overall, six independent wall model, L-shaped, roofed L-shaped, BOX-shaped walls with symmetric loading, BOX -shaped wall with asymmetrical loading and roofed BOX-shaped wall were built. Then the models are strengthened without strengthened reinforcement and with strengthened reinforcements with an angle of 30, 45 and 60 degrees. The applied lateral loading, is exerted by changing the location on the end wall. In BOX-shaped wall, in symmetric and asymmetric loading, the load bearing capacity will be increased about 200 and 50% respectively. Now, if strengthened, the load bearing capacity in symmetric and asymmetric loading will be increased 3.5 and 2 times respectively. The effective angle of placement of strengthened reinforcement in the independent wall is 45 and 60 degrees. But in BOX-shaped and L-shaped walls, the use of strengthened reinforcement 45 degrees is recommended.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권4호
• /
• pp.99-108
• /
• 2007

풍하중 및 지진하중등 횡하중이 작용하는 무량판 슬래브는 전단파괴와 같은 취성파괴를 지연시키기 위해서 충분한 전단강도와 연성능력을 보유하여야 한다. 본 연구에서는 반복 횡하중을 받는 무량판 슬래브의 전단강도와 변형성능을 고찰하기 위하여, 무보강 및 전단 보강된 총 4개의 내부기둥-슬래브 접합부를 실험하였다. 실험결과, 전단보강 슬래브의 이방향 전단강도는 무보강 슬래브보다 최대 1.5배까지 증가시켜 적용하는 콘크리트구조설계기준(KCI)과 ACI 318-02 기준은 중력하중만이 작용하는 경우에는 적절하나 조합하중 특히 횡하중의 영향이 클 경우에는 매우 불안전측 이었다. 한편, 변형성능 측면에서 슬래브-기둥 접합부의 1.5% 횡변위 성능을 확보하기 위하여 이방향 전단강도에 대한 중력하중비를 40%이하로 제한한 ACI-ASCE 352 위원회의 권고는 안전측인 것으로 나타났다.

• Earthquakes and Structures
• /
• 제8권6호
• /
• pp.1277-1297
• /
• 2015

Post-tensioned precast segmental bridge columns have shown high level of strength and ductility, and low residual displacement, which makes them suffer minor damage after earthquake loading; however, there is still lack of confidence on their lateral response against severe seismic loading due in part to their low energy dissipation capacity. This study investigates the influence of major design factors such as post-tensioning force level, strands position, columns aspect ratio, steel jacket and mild steel ratio on seismic performance of self-centring segmental bridge columns in terms of lateral strength, residual displacement and lateral peak displacement. Seismic analyses show that increasing the continuous mild steel ratio improves the lateral peak displacement of the self-centring columns at different levels of post-tensioning (PT) forces. Such an increase in steel ratio reduces the residual drift in segmental columns with higher aspect ratio more considerably. Suggestions are proposed for the design of self-centring segmental columns with various aspect ratios at different target drifts.