• 대한기계학회논문집A
• /
• 제24권7호
• /
• pp.1801-1809
• /
• 2000

A study on the topology optimization of Hard-Disk-Driver(HDD) actuator arm in free vibration is presented. The purpose of this research is to increasse the natural frequency of the first lateral mode of the HDD actuator arm under the constraint of total moment of inertia, so as to facilitate the position control of high speed actuator am. The first lateral mode is an important factor in the position control process. Thus the topology optimization for 2-D model of the HDD actuator arm is considered. A new objective function corresponding to multieigenvalue optimization is suggested to improve the solution of the eigenvalue optimization problem. The material density of the structure is treated as the design variable and the intermediate density is penalized. The effects of different element types and material property functions on the final topology are studied. When the problem is discretized using 8-node element of a uniform density, the smoothly-varying density field is obtained without checker-board patterns incurred. As a result of the study an improved design of the HDD actuator arm is suggested. Dynamic characteristics of the suggested design are compared computationally with those of the old design. With the same amount of the moment of inertia, the natural frequency of the first lateral mode or the suggested design is subsequently increased over the existing one.

• Earthquakes and Structures
• /
• 제15권5호
• /
• pp.529-540
• /
• 2018

The influences of initial damage paths and aftershock (AS) spectral shape on the assessment of AS collapse fragility are investigated. To do this, a four-story ductile reinforced concrete (RC) frame structure is employed as the study case. The far-field earthquake records recommended by FEMA P695 are used as AS ground motions. The AS incremental dynamic analyses are performed for the damaged structure. To examine the effect of initial damage paths, a total of six kinds of initial damage paths are adopted to simulate different initial damage states of the structure by pushover analysis and dynamic analysis. For the pushover-based initial damage paths, the structure is "pushed" using either uniform or triangle lateral load pattern to a specified damage state quantified by the maximum inter-story drift ratio. Among the dynamic initial damage paths, one single mainshock ground motion or a suite of mainshock ground motions are used in the incremental dynamic analyses to generate a specified initial damage state to the structure. The results show that the structure collapse capacity is reduced as the increase of initial damage, and the initial damage paths show a significant effect on the calculated collapse capacities of the damaged structure (especially at severe damage states). To account for the effect of AS spectral shape, the AS collapse fragility can be adjusted at different target values of ${\varepsilon}$ by using the linear correlation model between the collapse capacity (in term of spectral intensity) and the AS ${\varepsilon}$ values, and coefficients of this linear model is found to be associated with the initial damage states.

• 한국지반환경공학회 논문집
• /
• 제18권11호
• /
• pp.27-33
• /
• 2017

Nonlinear dynamic analysis is performed to calculate the response of U-shaped cantilever retaining structure under seismic loading using the finite element (FE) analysis program OpenSees. A particular interest of the study is to evaluate whether the moment demand in the cantilever can be accurately predicted, because it is an important component in the seismic design. The numerical model is validated against a centrifuge test that was performed on cantilever walls with dry medium dense sand in backfill. Seismic analysis is performed using the pressure-dependent, multi-yield-surface, plasticity based soil constitutive model implemented in OpenSees. Normal springs are used to simulate the soil-structure interface. Comparison with centrifuge show that FE analysis provides good estimates of both the acceleration response and bending moment. The lateral earth pressure near the bottom of the wall is overestimated in the numerical model, but this does not contribute to a higher prediction of the moment.

• 한국항공우주학회지
• /
• 제31권3호
• /
• pp.39-49
• /
• 2003

본 논문에서는 먼저 델타연산자 접근법과 섭동기법을 소개하였다. 전자는 수치연산에 있어서 round-off error를 줄여주고 후자는 시스템을 빠른 종속시스템과 느린 종속시스템으로 분리하여 연산시간을 줄여준다. 항공기의 동력학은 종방향 혹은 횡방향 모두 장주기(Phugoid)와 단주기 운동을 동시에 보여준다. 여기서는 경비행기 Beaver의 횡방향 모델에 섬동기법과 델타접슨법을 적용하여 얻는 근사치 해를 정확한 해와 비교하였다. 그 겨로가 개루프 시스템의 경우는 단 한번의 iteration을 시행하여 얻은 근사치 해가 정확한 해와 일치했고, 페루프 시스템의 경우는 iteration없이도 근사치 값이 정확한 해와 일치하였다. 이로써 제안된 방법들의 적용이 항공기 동력학 및 제어에 있어서 매우 유효함이 검증되었다.

• 농업과학연구
• /
• 제50권4호
• /
• pp.773-784
• /
• 2023

In this study, we developed a dynamic model and steering controller model for an autonomous tractor and evaluated their performance. The traction force was measured using a 6-component load cell, and the rotational speed of the wheels was monitored using proximity sensors installed on the axles. Torque sensors were employed to measure the axle torque. The PI (proportional integral) controller's coefficients were determined using the trial-error method. The coefficient of the P varied in the range of 0.1 - 0.5 and the I coefficient was determined in 3 increments of 0.01, 0.05, and 0.1. To validate the simulation model, we conducted RMS (root mean square) comparisons between the measured data of axle torque and the simulation results. The performance of the steering controller model was evaluated by analyzing the damping ratio calculated with the first and second overshoots. The average front and rear axle torque ranged from 3.29 - 3.44 and 6.98 - 7.41 kNm, respectively. The average rotational speed of the wheel ranged from 29.21 - 30.55 rpm at the front, and from 21.46 - 21.63 rpm at the rear. The steering controller model exhibited the most stable control performance when the coefficients of P and I were set at 0.5 and 0.01, respectively. The RMS analysis of the axle torque results indicated that the left and right wheel errors were approximately 1.52% and 2.61% (at front) and 7.45% and 7.28% (at rear), respectively.

• Structural Engineering and Mechanics
• /
• 제47권5호
• /
• pp.661-678
• /
• 2013

As a new type of vibration reduction, the ladder track system has been successfully used in engineering. In this paper, a numerical model of the train-track-viaduct system is established to study the dynamic responses of an elevated bridge with ladder track. The system is composed of a vehicle submodel, a track submodel and a bridge submodel, with the measured track irregularities as the system self-excitation. The whole time histories of a train running through an elevated bridge with $3{\times}27m$ continuous PC box girders are simulated. The dynamic responses of the bridge such as deflections, lateral and vertical accelerations, and the vehicle responses such as derailment factors, offload factors and car-body accelerations are calculated. The calculated results are partly validated through the comparison with the experimental data. Compared to the common slab track, adapting the ladder sleeper can effectively reduce the accelerations of the bridge girder, and also reduce the car-body accelerations and offload factors of the train vehicle.

• Smart Structures and Systems
• /
• 제19권5호
• /
• pp.523-538
• /
• 2017

A series of field vibration tests are conducted on the Runyang Suspension Bridge during both the construction and operational stages. The purpose of this study is devoted to the analysis of the dynamic characteristics of the suspension tower. After the tower was erected, an array of accelerometers was deployed to study the evolution of its modal parameters during the construction process. Dynamic tests were first performed under the freestanding tower condition and then under the tower-cable condition after the superstructure was installed. Based on the identified modal parameters, the effect of the pile-soil-structure interaction on dynamic characteristics of the suspension tower is investigated. Moreover, the stiffness of the pile foundation is successfully identified using a probabilistic finite model updating method. Furthermore, challenges of identifying the dynamic properties of the tower from the coupled responses of the tower-cable system are discussed in detail. It's found that compared with the identified results from the freestanding tower, the longitudinal and torsional natural frequencies of the tower in the tower-cable system have changed significantly, while the lateral mode frequencies change slightly. The identified modal results from measurements by the structural health monitoring system further confirmed that the vibrations of the bridge subsystems (i.e., the tower, the suspended deck and the main cable) are strongly coupled with one another.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집 특별세미나,특별/일반세션
• /
• pp.225-230
• /
• 2009

From the view point of railway vehicle dynamics, the interaction between wheel and rail have an huge effect on the behavior of the vehicle. This phenomenon is an unique motion, only for railway vehicles. Furthermore, close investigation of the backgrounds of the interaction is the key to estimate the dynamic behavior of the vehicle, successfully. To evaluate the model including flexible bodies such as car body and catenary system of the next generation express train, it is necessary to develop proper dynamic solver including a wheel rail contact module. In this study, wheel-rail contact module is developed using the general purpose dynamic solver. First of all, the procedure for calculation of the wheel-rail contact force has been established. Generally, yaw angle of the wheelset is ignored. Sets of information are summarized as tables and splined for further uses. With this information, normal force and creep coefficient can be extracted and used for FASTSIM algorithm, which has been shown good reliability over years. Normal force and longitudinal, lateral force at the contact surface are also calculated. Those data are verified by commercial railway simulation program 'VAMPIRE'. This procedure and program can offer a basic process for estimation of the dynamic behavior and wear of the wheel-rail system, even while running on the curved rail. Finally, multi-dimensional inspection tool will be developed including the prediction of the derailment.

• 한국해안해양공학회지
• /
• 제10권2호
• /
• pp.64-72
• /
• 1998

해저자원개발에 사용되는 riser나 TLP의 인장각과 같은 세장해양구조물의 파랑 및 상단부유체의 운동에 대한 동적거동해석을 수행하였다. 구조부재의 유한요소모델을 사용한 수치해석기법을 개발하고 규칙파에 대한 시간영역해석을 수행하였다. 본 연구는 상단부유체의 수평 및 수직운동이 구조물의 횡방향거동에 미치는 영향을 분석하였으며, 특히 부유체 수직운동의 영향을 주로하여 패러미터연구를 수행하였다. 수심, 파랑조건 그리고 부유체운동 등 여러경우에 대한 구조물의 변의, 휨응력을 비교검토하였고, 이 해석을 통하여 부유체의 수직운동에 의한 시간변화 인장력으로 야기되는 불안정조건을 검토하였다. 예제해석결과, 부유체의 수평 및 수직운동의 상호작용으로 riser의 동적응답이 증폭되었다. TLP 인장각의 경우 부유체의 수직운동효과가 구조물의 거동에 상당히 크게 작용하는 것으로 나타났다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.267-270
• /
• 1996

This paper reports about the successful suspension of a glass plate by electrostatic forces. In order to implement a stable suspension, the electrostatic forces exerted on the glass plate are actively controlled on the basis of the gap lengths between the glass plate and the stator electrodes. In this paper, the dynamic model of the suspension system and the influence of the resistivity of glass on the system stability are described, followed by stator electrode design, the experimental apparatus and a stabilizing controller. Experimental results show that the glass plate can be suspended at a gap length of about 0.3 mm. The influence of air humidity on the suspension initiation time, and the lateral dynamic characteristic are also described.