• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.346-349
• /
• 2015

Generally, in order to verify the degree of tire wear or abnormal wear, a driver or an auto mechanic checks the degree of tire wear and the existence of tire abnormality, directly with the naked eye or by way of using a gauge equipment. In case of such verification, individual subjective judgments may be involved or a driver may suffer heavy burdens to expend the time and cost for using the wheel alignment equipment. Therefore, this thesis will use a number of laser sensors to check the existence of abnormal wear and the degree of wear on each tire and develop a system checking the sides of tires to receive the tire information, so that subjective judgments may be overcome and objective and accurate judgments may be rendered.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.231-232
• /
• 2008

The coupling between electric, magnetic, and structural order parameters results in the so-called multiferroics, which possess ferroelectricity, ferromagnetism, and/or ferroelasticity. The simultaneous ferroelectricity and ferromagnetism (magnetoelectricity) allow potential applications in information storage, spintronics, and in magnetic or electric field sensors. Perovskite compound $BiFeO_3$ (BFO) is antiferromagnetic below Neel temperature of 647K and ferroelectric with a high Curie temperature of 1043K. It exhibits weak magnetism at room temperature(RT) due to the residual moment from a canted spin structure. It is likely that non-stoichiometry and second-phase formation are the factors which cause leakage in BFO. It has been suggested that oxygen non-stoichiometry leads to valence fluctuations of Fe ions in BFO, resulting in high conductivity. To reduce the large leakage current of BFO, one attempt is fabricating donor doped BFO compounds and thin films. We report here the successful fabrication of the Nd, Ti co-doped $BiFeO_3$ ceramics and thin films by pulsed laser deposition technique.

• ETRI Journal
• /
• v.28 no.6
• /
• pp.770-776
• /
• 2006

This paper presents a hyperspectral imaging technique based on laser-induced fluorescence for non-invasive detection of tumorous tissue on mouse skin. Hyperspectral imaging sensors collect image data in a number of narrow, adjacent spectral bands. Such high-resolution measurement of spectral information reveals contiguous emission spectra at each image pixel useful for the characterization of constituent materials. The hyperspectral image data used in this study are fluorescence images of mouse skin consisting of 21 spectral bands in the visible spectrum of the wavelengths ranging from 440 nm to 640 nm. Fluorescence signal is measured with the use of laser excitation at 337 nm. An acousto-optic tunable filter (AOTF) is used to capture images at 10 nm intervals. All spectral band images are spatially registered with the reference band image at 490 nm to obtain exact pixel correspondences by compensating the spatial offsets caused by the refraction differences in AOTF at different wavelengths during the image capture procedure. The unique fluorescence spectral signatures demonstrate a good separation to differentiate malignant tumors from normal tissues for rapid detection of skin cancers without biopsy.

• Journal of Mechanical Science and Technology
• /
• v.15 no.12
• /
• pp.1775-1783
• /
• 2001

For two decades, there has been an active research to enhance the performances of Particle Image Velocimetry (PIV) systems. However, the resulting systems are somewhat very costly, cumbersome and delicate. In this paper, we address the design and some first experimental results of a PIV system belonging to the opposite paradigm. The Miniature PIV or MPIV system feature relatively modest performances, but is considerably smaller (out MPIV could hold in dia. 40 mm$\times$120 mm), cheaper (out MPIV total cost is less than $500) and easy to handle. Potential applications include industrial velocity sensors. The proposed MPIV system uses a one-chip-only CMOS camera with digital output. Only two other chips are needed, one for a buffer memory and one for an interfacing logic that controls the system. Images are transferred to a personal computer (PC or laptop) via its standard parallel port. No extra hardware is required (in particular, no frame grabber board is needed). In our first MPIV prototype presented in this paper, the strobe lighting is generated by a cheap 5 mW laser pointer diode. Experimental results are presented and discussed.

• Journal of Welding and Joining
• /
• v.8 no.3
• /
• pp.60-69
• /
• 1990

Plasma arc cutting is a fusion cutting process in which a gas-constricted arc is employed to produce a high-temperature, high-velocity plasma jet on the workpiece. This process provides some advantages such as increased cutting velocity, excellent working accuracy and the ability to cut special materials (widely used stainless steels and Al-alloys, for example), when compared with iconventional oxyfuel gas cutting. From the view point of price and reliability of the power source, plasma arc cutting has also some distinct advantages over laser beam cutting. High-speed machines with NC or CNC systems are needed for the plasma arc or laser beam cutting process, while for oxyfuel gas cutting, low-speed machines with copying templates or optical-shape tracking sensors can be applied. The low price and high flexibility of the microprocessor arc contributing more and more the application of CNC system in the plasma arc cutting process, as in other manufacturing fields. From these points of view, a microprocessor-based plasma arc cutting system was developed by using a reference-pulse system, and its performance was tested. The interpolating routines were programmed in the assembly language for saving the memory volume and improving the compouting speed, which has an intimate relationship with the available cutting velocity.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.840-840
• /
• 2003

Operational Modal Analysis (OMA) is a technique for identification of modal parameters by measurement of only the system's response. On many lightweight structures, such as load-speaker cones and disk drive read/write heads, is impossible or impractical to measure the input forces. Another characteristic of lightweight structure is their sensitivity to mass loading from sensors. The Scanning Laser Doppler Vibrometry(SLDV) allows response measurements to be taken without mass loading. One disadvantage of OMA testing compared to tradition input output modal testing is the OMA mode shapes are un-scaled. This means that the mode shape obtained from an OMA test can not used for analytical structural modification studies. However, the un-scaled mode shapes from an OMA test can be used to update a Finite Element Model (FEM). The updated FEM can then be used to analytically predict the effect of structural modifications. This paper will present the results of an OMA test performed on a simple plate and motor in operating conditions. The un-scaled mode shapes from this test will be used to update a FEM model of the system. The updated FEM model will be then be used to predict the effect of attaching a mass to the plate. The shapes predicted by the FEM for the modified system will be compared to a second OMA test on the modified system

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.285-286
• /
• 2006

The essential tasks to operate the welding robot are the acquisition of the position and/or shape of the parent metal. For the seam tracking or the robot automation, many kinds of contact and non-contact sensors are used. Recently, the vision sensor is most popular. In this paper, the development of the system which measures the profile of the welding part is described. The total system will be assembled into a compact module which can be attached to the head of welding robot system. This system uses the line-type structured laser diode and the vision sensor It implemented Direct Linear Transformation (DLT) for the camera calibration as well as radial distortion correction. The three dimensional shape of the parent metal is obtained after simple linear transformation and therefore, the system operates in real time. Some experiments are carried out to evaluate the performance of the developed system.

• Journal of Sensor Science and Technology
• /
• v.13 no.3
• /
• pp.252-257
• /
• 2004

$Y_{2}O_{3}:Eu^{3+}$ thin films have been grown on $Al_{2}O_{3}$(0001) substrates by a pulsed laser deposition (PLD) method. The phosphor thin films were deposited at a substrate temperature of 500, 600, and $700^{\circ}C$ under the oxygen pressure of 100, 200, and 300 mTorr. The crystallinity, surface roughness and photoluminescence of the films are highly dependent on the substrate temperature and oxygen pressure. The films grown on $Al_{2}O_{3}$(0001) substrate even under the different substrate temperatures and oxygen pressures exhibited (222) preferred orientation. The luminescent spectra exhibited strong luminescence of ${^{5}D_{0}}-{^{7}F_{2}}$ transition within $Eu^{+3}$ peaking at 612 nm. The crystallinity and luminescence intensity of the films have been improved as the substrate temperature increasing. With increase of oxygen pressure from 50 to 300 mTorr, the crystallinity of the films has been uniformly decreased. The photoluminescence intensity and surface roughness have similar behaviors as a function of oxygen pressure. At 200 mTorr, both photoluminescence intensity and surface roughness show a maximum.

• Korean Journal of Optics and Photonics
• /
• v.15 no.5
• /
• pp.449-454
• /
• 2004

The optical limiter is an optical component which reduces laser beam intensity for the protection of eyes and light sensors. Carbon nanotube is now known as a highly efficient optical limiting material. Optical limiting effect of the multi-walled carbon nanotube suspensions, in several kinds of solvents such as distilled water, chloroform, ethanol and ethylene glycol, were measured in the range from room temperature to near to the boiling points of the solvents. The pulsed Nd:YAG laser whose wavelength is 1064 nm and pulse duration is 6 ns was used as a light source. The experimental result shows that the limiting efficiency was reduced as the temperature increased, and the suspension which has lower boiling point, viscosity and surface tension has highest efficiency.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.10
• /
• pp.1051-1056
• /
• 2014

In this paper, we introduce an intelligent robotic arc welding system which exploits sensors like as LVS (Laser Vision Sensor), Hall effect sensor, voltmeter and so on. The use of industrial robot is saturated because of its own limitation, and one of the major limitations is that industrial robot cannot recognize the environment. Lately, sensor-based environmental awareness research of the industrial robot is performed actively to overcome such limitation, and it can expand application field and improve productivity. We classify the sensor-based intelligent arc welding robot system by the goal and the sensing data. The goals can be categorized into detection of a welding start point, tracking of a welding line and correction of a torch deformation. The Sensing data can be categorized into welding data (i.e. current, voltage and short circuit detection) and displacement data (i.e. distance, position). This paper covers not only the explanation of the each category but also its advantage and limitation.