• Current Applied Physics
• /
• v.18 no.12
• /
• pp.1492-1495
• /
• 2018

This paper studies the influence of temperature on electrical resistivity in ${\alpha}-InAs$ thin films between 30 K-2K based on the analysis of Mott VRH model and ES VRH model. The effect of the interactions between electrons at lower temperature must be considered, therefore, ES VRH conduction will dominate mechanism, and the crossover from Mott to ES VRH conduction is observed about 7 K. Based on available experiment data and VRH conduction model, the parameters of VRH conduction are determined. And the calculated values of $T_C$ are consistent with the experimental results. In addition, $R_M/{\xi}$, ${\Delta}_M/kT$, $R_{ES}/{\xi}$ and ${\Delta}_{ES}/kT$ are satisfied with the validity of Mott and ES models. Furthermore, the temperature dependence of resistivity at low temperature obeys a universal scaling law, which well describes the overall temperature range of VRH conduction. However, the values of $T^{\prime}_M$ from the universal function are two order of magnitudes lower than $T_M$ deduced from fitting experiment.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.20 no.4
• /
• pp.371-382
• /
• 2022

Carbonates are inorganic ligands that are abundant in natural groundwater. They strongly influence radionuclide mobility by forming strong complexes, thereby increasing solubility and reducing soil absorption rates. We characterized the spectroscopic properties of Am(III)-carbonate species using UV-Vis absorption and time-resolved laser-induced fluorescence spectroscopy. The deconvoluted absorption spectra of aqueous Am(CO₃)₂^- and Am(CO₃)₃^3- species were identified at red-shifted positions with lower molar absorption coefficients compared to the absorption spectrum of aqua Am³⁺. The luminescence spectrum of Am(CO₃)₃^3- was red-shifted from 688 nm for Am³⁺ to 695 nm with enhanced intensity and an extended lifetime. Colloidal Am(III)-carbonate compounds exhibited absorption at approximately 506 nm but had non-luminescent properties. Slow formation of colloidal particles was monitored based on the absorption spectral changes over the sample aging time. The experimental results showed that the solubility of Am(III) in carbonate solutions was higher than the predicted values from the thermodynamic constants in OECD-NEA reviews. These results emphasize the importance of kinetic parameters as well as thermodynamic constants to predict radionuclide migration. The identified spectroscopic properties of Am(III)-carbonate species enable monitoring time-dependent species evolution in addition to determining the thermodynamics of Am(III) in carbonate systems.

• Progress in Superconductivity
• /
• v.2 no.2
• /
• pp.76-80
• /
• 2001

We have fabricated YBa$_2$Cu$_3$$O_{7-x}$ (YBCO) ramp-edge Josephson junctions by modifying ramp edges of the base electrodes without depositing any artificial barrier layer. YBa$_2$Cu$_3$O/7-x//SrTiO$_3$ (YBCO/STO) films were deposited on SrTiO$_3$(100) by on-axis KrF laser deposition. After patterning the bottom YBCO/STO layer, the ramp edge was cleaned by ion-beam and then reacted with deionized water under various conditions prior to the deposition of counter-electrode layers. The top YBCO/STO layer was deposited and patterned by photolithography and ion milling. We measured current-voltage (I-V) characteristics, magnetic field modulation of the critical current at 77 K. Some showed resistively shunted junction (RSJ)-type I-V characteristics, while others exhibited flux-flow behaviors, depending on the dipping time of the ramp edge in deionized water. Junctions fabricated using optimized conditions showed fairly uniform distribution of junction parameters such as I$_{c}$R$_{n}$ values, which were about 0.16 mV at 77 K with 1$\sigma$~ 24%. We made a dc SQUID with the same deionized water treated junctions, and it showed the sinusoidal modulation under applied magnetic field at 77 K. 77 K.

• The Journal of the Society of Stroke on Korean Medicine
• /
• v.10 no.1
• /
• pp.8-19
• /
• 2009

Scutellaria Radix, originated from Scutellaria baicalensis Georgi, is one of the most important medicine in traditional Oriental medicine, and possesses anti-bacterial activity and sedative effects, can be applied in the treatment of a range of conditions including diarrhea and hepatitis. It is reported that chronic global ischemia induces neuronal damage in selective, vulnerable regions of the brain, especially the hippocampus and cerebral cortex. In the present study, to investigate the effect of Scutellaria Radix extract on cerebral disease, the changes of regional cerebral blood flow and pial arterial diameter on ischemia/reperfusion state was determinated by Laser-Doppler Flowmetry and some parameters concerned with oxidative stress also measured. When SRe were administered for five days with the concentration of 100 mg/kg, GSH activity significantly increased. But SRe administeration showed no significant change in lipid peroxidation. When the activities of CAT, Cu, Zn-SOD and GSH were measured, CAT and GSH were activated by SRe administration. When 1 and 3 ㎍/㎖ SRe was applied to the neuronal cell cultures, the quantities of LDH was significantly reduced when compared with cultures treated only with NMDA. Through this study, it can be concluded that the ischemia/reperfusion induced brain stress may have contributed to cerebral damage in rats, and the present study provides clear evidence for the beneficial effect of SRe on ischemia induced brain injury.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.81.2-81.2
• /
• 2012

To fabricate a metal mold for injection molding, hot-embossing and imprinting process, mechanical machining, electro discharge machining (EDM), electrochemical machining (ECM), laser process and wet etching ($FeCl_3$ process) have been widely used. However it is hard to get precise structure with these processes. Electrochemical etching has been also employed to fabricate a micro structure in metal mold. A through mask electrochemical micro machining (TMEMM) is one of the electrochemical etching processes which can obtain finely precise structure. In this process, many parameters such as current density, process time, temperature of electrolyte and distance between electrodes should be controlled. Therefore, it is difficult to predict the result because it has low reliability and reproducibility. To improve it, we investigated this process numerically and experimentally. To search the relation between processing parameters and the results, we used finite element simulation and the commercial finite element method (FEM) software ANSYS was used to analyze the electric field. In this study, it was supposed that the anodic dissolution process is predicted depending on the current density which is one of major parameters with finite element method. In experiment, we used stainless steel (SS304) substrate with various sized square and circular array patterns as an anode and copper (Cu) plate as a cathode. A mixture of $H_2SO_4$, $H_3PO_4$ and DIW was used as an electrolyte. After electrochemical etching process, we compared the results of experiment and simulation. As a result, we got the current distribution in the electrolyte and line profile of current density of the patterns from simulation. And etching profile and surface morphologies were characterized by 3D-profiler(${\mu}$-surf, Nanofocus, Germany) and FE-SEM(S-4800, Hitachi, Japan) measurement. From comparison of these data, it was confirmed that current distribution and line profile of the patterns from simulation are similar to surface morphology and etching profile of the sample from the process, respectively. Then we concluded that current density is more concentrated at the edge of pattern and the depth of etched area is proportional to current density.

• Journal of the Korean Magnetics Society
• /
• v.17 no.1
• /
• pp.18-21
• /
• 2007

The hexagonal $HoMn_{1-x}-Fe_xO_3$(x=0.00, 0.05) thin films were prepared using pulsed laser deposition(PLD) method on $Pt/Ti/SiO_2/Si$ substrate. The microstructure and magnetic properties have been studied by x-ray diffraction(XRD), atomic force microscopy (AFH), scanning electron microscope(SEM:), x-ray photoelectron spectroscopy(XPS), and conversion electron $M\"{o}ssbauer$ spectroscopy(CEMS). From the analysis of the x-ray diffraction patterns, the crystal structure for all films was found to be a hexagonal($P6_3cm$), which was preferentially grown along(110) direction. The lattice constant $c_0$ of the film with x=0.05 was close to that of single crystal, whereas lattice constant $a_0$ with respect to single crystal shows a slight decrease. This difference of lattice parameters between film and single crystal was caused by the lattice mismatch between the film and $Pt/Ti/SiO_2/Si$ substrate. Conversion electron $M\"{o}ssbauer$ spectrum of $HoMn_{0.95}Fe_{0.05}O_3$ thin film shows an asymmetry doublet absorption ratio at room temperature, which is due to the oriented direction of crystallographic domains. This is corresponding with analysis of x-ray diffraction. The quadrupole splitting(${\Delta}E_Q$) at room temperature is found to be $1.62{\pm}0.01mm/s$. This large ${\Delta}E_Q$ was caused by asymmetry environment surrounding Fe ion.

• Clinical and Experimental Reproductive Medicine
• /
• v.35 no.3
• /
• pp.193-202
• /
• 2008

Objective: To evaluate efficacy of assisted hatching by laser (AHL) and acidified Tyrode solution (AHA) in selected groups of IVF-ET patients who have a poor prognosis. Methods: From February 2006 to September 2006, total of 328 IVF-ET cycles with advanced female age (${\geq}38$ years), recurrent implantation failure (${\geq}3$ cycles), thick zona (${\geq}17{\mu}m$), and/or poor quality of embryo were randomly divided into assisted hatching by acidified Tyrode solution (AHA, n=180) and the assisted hatching using the ZILOS-tk laser (AHL, n=148) groups. Clinical outcomes were analyzed and compared between AHA and AHL group based on the patient characteristics. Results: In all AHL and AHA group, there were no significant differences in pregnancy (42.6%, 63/148 vs. 33.3%, 60/180) and implantation rates (17.4%, 82/470 vs. 16.0%, 89/556) However, in advanced female age group (Group 1), pregnancy (37.0%, 20/54 vs. 18.7%, 14/75) and implantation rates (14.4%, 23/160 vs. 7.1%, 15/210) in AHL group were significantly (p<0.05) higher than those of AHA, although there was no difference in patient parameters of both groups. And, the clinical outcome of groups with recurrent implantation failure (Group 2), thick zona pellucida (Group 3) and poor quality embryo (Group 4) were improved in AHL compared to those of AHA: 43.8% (21/48) and 31.6% (25/79) in Group 2, 43.8% (32/73) and 34.1% (28/82) in Group 3, 25.0% (7/28) and 14.6% (6/41) in Group 4, but no significance. Conclusion: The AHL improved the pregnancy and implantation rates in patients with advanced female age and recurrent implantation failure when compared to outcomes achieved from AHA. Therefore, this AHL technique may be a efficient and safe method for patients with poor prognosis.

• Journal of Oral Medicine and Pain
• /
• v.31 no.3
• /
• pp.223-229
• /
• 2006

The objectives of this study was to investigate the amount of tooth ablation and the change of intrapulpal temperature by Er:YAG laser as it relates to pulse energy and pulse repetition rate at the identical power and, thereby, to reveal which of the two parameters strongly relates with ablation efficiency and intrapulpal temperature. Extracted healthy human molar teeth were sectioned into two pieces and each specimen was irradiated within the combination of pulse energy and pulse repetition time at the same power of 3W; $300mJy{\times}10Hz$ group, $200mJy{\times}15Hz$ group, and $150mJy{\times}20Hz$ group. Each specimen comprised ten tooth specimens. A laser beam with conjunction of a water flow rate of 1.6 ml/min was applied over enamel surfaces of the specimens during 3 seconds and the ablation amount was determined by difference in weight before and after irradiation. To investigate the temperature change in the pulp according to the above groups, another five extracted healthy human molar teeth were prepared. Each tooth was embedded into resin block and the temperature-measuring probes were kept on the irradiated and the opposite walls in the dental pulp during lasing. When the power was kept constant at 3W, ablation amount increased with pulse energy rather than pulse repetition rate (p=0.000). Although intrapulpal temperature increased with pulse repetition rate, there were no significant differences among the groups and between the irradiated and the opposite pulpal walls, except at a condition of $150y{\times}20Hz$ (p=0.033). Conclusively, it is suggested that ablation efficacy is influenced by pulse energy rather than pulse repetition rate.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.45 no.6
• /
• pp.26-34
• /
• 2008

The information of traversability and path planning is essential for UGV(Unmanned Ground Vehicle) navigation. Such information can be obtained by analyzing 3D terrain. In this paper, we present the method of 3D terrain modeling with color information from a camera, precise distance information from a 2D Laser Range Finder(LRF) and wheel encoder information from mobile robot with less data. And also we present the method of 3B terrain modeling with the information from GPS/IMU and 2D LRF with less data. To fuse the color information from camera and distance information from 2D LRF, we obtain extrinsic parameters between a camera and LRF using planar pattern. We set up such a fused system on a mobile robot and make an experiment on indoor environment. And we make an experiment on outdoor environment to reconstruction 3D terrain with 2D LRF and GPS/IMU(Inertial Measurement Unit). The obtained 3D terrain model is based on points and requires large amount of data. To reduce the amount of data, we use cubic grid-based model instead of point-based model.

• Journal of Yeungnam Medical Science
• /
• v.15 no.2
• /
• pp.297-305
• /
• 1998

Recently, several alternatives have been attempted in the management of benign prostatic hyperplasia (BPH) to reduce morbidity of traditional transurethral resection of the prostate (TURP). Among new modalities, transurethral electrovaporization (TEVP) is considered as a promising alternative. To evaluate the safety and initial efficacy of JEVP using the roller loop electrode (ProSurg Inc. USA) on BPH patients, we compared the results of TEVP with those of TURP and visual laser ablation of the prostate (VLAP). In this study, a total of 115 patients with symptomatic BPH were underwent TEVP (n=17), TURP (n=59) or VLAP (n=39) since 1995. Before treatment, patients were evaluated with an International Prostate Symptom Score (IPSS) and the measurement of maximal uroflow rate (MFR) and postvoid residual urine (PVR). After treatment, the operative and hospital records were reviewed. The uroflowmetry and IPSS were re-evaluated 3-10 months after treatment. In clinical outcome of re-evaluation compared to the preoperative parameters, there was a clinically significant improvement in three procedures. TEVP resulted in 62% reduction in IPSS (TURP, 73% : VLAP, 69%), 84% improvement in MFR (TURP, 113% : VLAP, 91%), and 74% reduction in PVR (TURP, 88% : VLAP, 78%). TEVP had shorter duration of hospitalization and catheterization than the others. TEVP was associated with lower rates of treatment-related complication than TURP. In conclusions, TEVP is considered as a useful procedure to treat symptomatic BPH. And, the advantages of TEVP over TURP include excellent intraoperative hemostasis, lower morbidity, shorter hospital stay and simple technique. In addition the advantages over VLAP include lower cost, shorter duration of catheterization and early symptom improvement.