• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.24 no.4
• /
• pp.129-134
• /
• 2024

In this paper, This paper is a liquid droplet discharge system using a water level sensor that can linearly detect changes in water level through experiments with an infrared sensor, a laser sensor, an ultrasonic sensor, and a capacitance sensor. SMPS, regulator 5V, and LDO 3.3V were designed for power supply. A water level sensor input ADC circuit and microprocessor were used. Solenoid valve control, pump output control unit for positive/negative pressure generation, CAN, Ethernet, UART communication, and USB for industrial communication were used. The change in pressure was confirmed through the change in water level, the change in pressure was minimized, and a system for discharging liquid droplets was implemented.

• Korean Journal of Optics and Photonics
• /
• v.29 no.6
• /
• pp.241-246
• /
• 2018

In this paper, a low-cost optical temperature sensor is implemented, using a fiber Bragg grating (FBG) as the temperature probe and a low-cost VCSEL with temperature-dependent output wavelength as the light source. To analyze the wavelength of the reflected light from the FBG, an interrogation was applied using a method of referring to the internal temperature according to the output wavelength of the VCSEL. When the temperature of the VCSEL was adjusted from 14 to $52.2^{\circ}C$, the output wavelength varied from 1519.90 to 1524.25 nm. The degree of wavelength tuning according to temperature was $0.114nm/^{\circ}C$. The variable wavelength repeatability error according to temperature was ${\pm}0.003nm$, and the temperature measurement error was ${\pm}0.18^{\circ}C$. As a result of measuring the temperatures from 22.3 to $194.2^{\circ}C$, the value of the internal temperature change of the light source according to the applied temperature ${\Delta}T$ was $0.146^{\circ}C/{\Delta}T$, the change in reflected wavelength of the temperature probe according to applied temperature ${\Delta}T$ was measured at $16.64pm/^{\circ}C$. and the temperature measurement error of the sensor was ${\pm}1^{\circ}C$.

• Journal of Periodontal and Implant Science
• /
• v.27 no.3
• /
• pp.603-619
• /
• 1997

The use of laser in the treatment of soft tissue minimizes hemorrhage, provides better view of the operating field, and thereby minimizes operating time. Also, there will be far less post-operative swelling, pain and scar formation, and sterilizing effect are shown in some portions of the wound site. All these advantages of laser therapy contribute to its widespread use in the field of medicine and dentistry. Regarding such facts, we used CO2 laser of different watts in gingivectomy for white rats to compare initial healing process. For the control group, the least amount of output in performing gingivectomy(4watts) was offered, and for the experimental group, 6watts was given. Animals were sacrificed on the second, third days, 1 weeks, 2 weeks, and 3 weeks after operation, and their specimens were histologically analyzed. The following results were obtained: 1. Blood clot of small size was observed in both the control and experimental groups after two days, and no more thereafter. 2. In both the control and experimental groups, the inflammation zone size was the greatest after two days, and it decreased gradually to become almost invisble by the second week. The experimental group showed larger size of inflammation zone during second and third days: however, there was no difference after one week. 3. Granulation tissue in both the control and experimental groups showed gradual maturation with time, and by the second week, it was almost replaced by normal connective tissue. By the third week, complete healing pattern was observed. The experimental group showed larger granulation tissue than the control group until the third day, but there was no significant difference after one week. 4. In both the control and experimental groups, gingival epithelialization began on the second day. After one week, regeneration of rete peg and partial formation of junctional epithelium were observed: by the second week, keratinization of oral sulcular epithelium began, and it was completed by the third week.

• Korean Journal of Optics and Photonics
• /
• v.24 no.1
• /
• pp.1-8
• /
• 2013

In this paper, we report design, fabrication and characterization of the WBRM (Wide Band Receiver Module) for LADAR (LAser Detection And Ranging) application. The WBRM has been designed and fabricated using self-made APD (Avalanche Photodiode) and TIA (Trans-impedance Amplifier). The APD and TIA chips have been integrated on 12-pin TO8 header using self-made ceramic submount and circuit. The WBRM module showed 450 ps of rise time, and corresponding 780 MHz bandwidth. Furthermore, it showed very low output noise less than 0.8 mV, and higher SNR than 15 for 150 nW of MDS(Minimum Detectable Signal). To the author's knowledge, this is the best performance of an optical receiver module for LIDAR fabricated by 200 um InGaAs APD.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.59-67
• /
• 2006

We demonstrate bidirectional long-reach 35-channel dense wavelength division multiplexing-passive optical network(DWDM-PON) based on wavelength-locked Fabry-Perot laser diodes (F-P LDs). The mode control of F-P LD enhances output power at decreased the required injection power. We show packet-loss-free transmission in all 70 channels at 125 Mb/s per channel line rate through 70 km of single mode fiber without optical amplifier The DWDM-PON can consolidate a metro network into an access network by bypassing the central offices within its reach. The proposed DWDM-PON can accommodate about 80 subscribers with an EDFA-based broadband light source. Further expansion up to 100 subscribers is possible with a semiconductor-based BLS.

• Korean Journal of Optics and Photonics
• /
• v.11 no.4
• /
• pp.271-278
• /
• 2000

We have fabricated and analyzed the lasing characteristics of 1.3$\mu\textrm{m}$ Spot-Size-Converter (SSC) integrated Fabry-Perot (FP) laser diodes, which are very promising light sources for optical subscriber networks. SSC-LDs has been developed by BIB (buttjoint-built-in) coupling and selective MOVPE growth. High-performances were achieved such as the slope efficiency from the SSC facet of 0.23-0.32 mW/mA, the full-width at the half maximum of the far-field pattern (FFP) of 9.5$^{\circ}$~12.3$^{\circ}$, the alignment tolerances of $\pm$2.3$\mu\textrm{m}$ and $\pm$2.5$\mu\textrm{m}$ within the extra-coupling loss of 1 dB for the vertical and parallel directions, respectively. These experimental results were compared to theoretical ones in order to clarify the operational problems and give a good design direction of the fabricated SSC-LDs. It was revealed that an asymmetric output power from the facets, an irrelevancy of FFP and the waveguide structure around SSC facet region, and a poor temperature characteristics were originated from the scattering in the BIB and SSC sections and SHB effect in the active section for the first time.t time.

• Korean Journal of Optics and Photonics
• /
• v.10 no.6
• /
• pp.500-506
• /
• 1999

We designed and fabricated a bidirectional optical transceiver module for low cost access network. An integrated chip forming a pin-PD on an 1.3 urn FP-LD was assembled by flip-chip bonding on a Si optical bench, a single mode fiber with an angled end facet was aligned passively with the integrated chip on V-groove of Si-optical bench. Gaussian beam theory was applied to evaluate the coupling coefficients as a function of some parameters such as alignment distance, angle of fiber end facet, vertical alignment error. The theory is also used to search the bottle-neck between transmittance and receiving coupling efficiency in the bi-directional optical system. Tn this paper, we confirmed that reduction of coupling efficiency by the vertical alignment error between laser beam and fiber core axis can be compensated by controlling the fiber facet angle. In the fabrication of sub-module, a'||'&'||' we made such that the fiber facet have a corn shape with an angled facet only core part, the reflection of transmitted laser beam from the fiber facet could be minimized below -35 dE in alignment distance of 2: 30 /J.m. In the same condition, transmitted output power of -12.1 dEm and responsivity of 0.2. AIW were obtained.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.42 no.2 s.302
• /
• pp.69-80
• /
• 2005

In these days, the technology development of the imaging/optic industry and the digital broadcasting replace the classic CRT with the new display devices that is getting slimmer and larger. Especially, when the general TV signal is applied directly to the wide gamut display using LED or laser, which can display higher chromatic colors that can't be reproduced on CRT, the color distortion occurs and it causes serious problems. Thus, in this paper the gamut mapping is studied, which gets rids of the color distortion and utilizes the wider color gamut than that of the CRT sufficiently. In the gamut mapping the general mapping concept is the increasement of the chroma on the same hue plane but it causes the over chromatic enhancement. So, the vector mapping, which increases the lightness md the chroma at the same time, is proposed to prevent the side effect. In the vector mapping the chromaticity is maintained constantly, hence the image can be seen more natural than that of the chroma mapping. By using the gamut fitting, it is compensated that the tone disappearance or the contour effect that is arose from the geometric properties of the input and the output color gamut. These gamut mapping and gamut fitting can prevent the color distortion and reproduce the natural image on the wide gamut displays.

• The KIPS Transactions:PartD
• /
• v.16D no.1
• /
• pp.133-138
• /
• 2009

This paper introduces a pilot CDMA network-based wireless lap time measurement system set up on a ski slope of Yongpyong Ski Resort. The wireless lap time measurement system is one output of U-Sports Project of Gangwon Province, which is intendended for promoting local strategic business and preparation for hosting 2018 Winter Olympic Games at Pyeongchang. A pair of laser sensors is installed at the entry and exit points of a section requiring lap time measurement on a ski slope. Each laser sensor is connected to a sensor node via wire so that the sensor node can detect the time when a skier enters or exits the section. Also each sensor node is connected to a CDMA network via a modem and receives a standard time from a NTP server. Each node executes the NTP algorithm to synchronize its local time to the received server time. As a result of the time synchronization, the sensor nodes maintain its local time within a resolution of at least 10 miliseconds and transmit the time of detection to a central control center. While the wireless lap time measurement system introduced in the paper does not need expensive measurement equipment, the system allows the central control center to provide lap time records in a more convenient manner compared to conventional manual lap time measuremnt methods.

• Journal of Sensor Science and Technology
• /
• v.9 no.3
• /
• pp.163-170
• /
• 2000

Optical frequency modulated fiber optic interferometric sensor was developed to sense the mechanical quantities, such as displacement, strain, force etc. It has been difficult to distinguish whether the increase of the mechanical quantities or the decrease of the quantities measured by the conventional fiber optic interferometric sensors because their signals only have a sinusoidal wave pattern related to the change of mechanical quantities. In this study, in order to measure the mechanical quantifies with the distinction of the changing direction of the quantities, the fiber of optic Michelson interferometric sensor was simply constructed by the laser light modulated with saw tooth wave pattern. The output signal of the sensor was controlled as the sinusoidal wave. The signal processing was based on the counting of the wave number of the output signal during constant time duration. The strain was determined by the cumulative value of the wave number producted by the gage factor. In order to verify the strain measurement capability of this sensor, the strain increase-decrease test was performed by universal testing machine installed with the aluminum specimen bonded with the fiber optic sensor and electrical strain gage. In the result of the test, the strain from the fiber optic sensor had a good agreement with the values from the electrical strain gage.