• Current Optics and Photonics
• /
• v.4 no.3
• /
• pp.238-246
• /
• 2020

The heat distribution in crystals in a 2-㎛ acousto-optic Q-switched Tm:LuAG laser pumped by pulsed-laser-diode (pulsed-LD) intermittent-pumping technology was analyzed using COMSOL software. The thermal lensing effect of the Tm:LuAG crystal can be mitigated by pulsed-LD intermittent-pumping techniques. An experimental setup using this kind of approach achieved maximum output energy of 8.31 mJ, minimum pulse width of 101.9 ns, and highest peak power of 81.55 kW, reached at a Q-switched repetition rate of 200 Hz. It offers significant improvement of performance of the output laser beam, compared to pulsed-LD double-ended pumping technology at the same repetition rate.

• Current Optics and Photonics
• /
• v.7 no.6
• /
• pp.714-720
• /
• 2023

Laser cleaning has the advantages of environmental protection, precision, and high efficiency, and has good prospects for application in removing oxide films on the surface of aluminum alloy. This paper discusses the cleaning threshold and cleaning mechanism of aluminum alloy surface oxide film. A nanosecond pulsed laser was used to remove a 5-㎛-thick oxide film from the surface of 7A04 aluminum alloy, and the target surface temperature and cleaning depth were simulated. The effects of different laser energy densities on the surface morphology of the aluminum alloy were analyzed, and the plasma motion process was recorded using a high-speed camera. The temperature measurement results of the experiment are close to the simulation results. The results show that the laser cleaning of aluminum alloy oxide film is mainly based on the vaporization mechanism and the shock wave generated by the explosion.

• Current Optics and Photonics
• /
• v.2 no.6
• /
• pp.582-588
• /
• 2018

A $Nd:YVO_4$ laser dual-end-pumped by a wavelength-locked 878.6 nm laser diode is presented. At the repetition rate of 500 KHz, the absorbed pump power of 58 W, an output power of 26.1 W at 1064 nm is obtained, corresponding to an optical-optical efficiency of 45%. The pulse width is 44.2 ns. Meanwhile, the effects of traditional 808 nm pumping and 878.6 nm dual-end-pumping on the output laser beam quality and pulse width are compared and analyzed in an experiment.

• Current Optics and Photonics
• /
• v.2 no.5
• /
• pp.448-452
• /
• 2018

A three-wavelength $Pr^{3+}:YLF$ laser at 604 nm, 607 nm and 640 nm simultaneously output by Fabry-Perot (F-P) etalon has been obtained. A 444 nm blue laser diode is used for pumping the $Pr^{3+}:YLF$ crystal, and a 0.1 mm F-P etalon is inserted in the resonator to select wavelength. The theoretical model of three-wavelength $Pr^{3+}:YLF$ laser is established, by adjusting the tilt angle of the etalon, the transmittances of the different wavelengths can be controlled, and the threshold values can be made to equalize by controlling the loss among different wavelengths. In the experiment, when the tilt angle of etalon is $9^{\circ}$ and the optimized length of resonator is 48 mm, the total output power of 25 mW at the three-wavelength is achieved at incident pump power of 7.5 W.

• Current Optics and Photonics
• /
• v.5 no.6
• /
• pp.721-729
• /
• 2021

We demonstrate a Pr³⁺:YLF 639.7-nm laser with single-frequency output based on the Q-switched pre-lase technology, pumped by a fiber-coupled GaN blue laser diode. The pre-lase technology is realized by the step-type loss of the acousto-optical Q-switched device. The conclusions of the theoretical research are verified experimentally. The mode-suppression ratio was 44 dB at the single-frequency laser output. Detection by interferometer verified the realization of the stable single-frequency laser. In addition, the emission spectrum had a linewidth of 139.9 MHz, measured by Fabry-Perot interferometer. The single-frequency laser's single-peak power was over 19.7 W with 98.8-ns pulse duration, obtained under an absorption power of 1.74 W.

• Current Optics and Photonics
• /
• v.5 no.1
• /
• pp.59-65
• /
• 2021

This paper reports a tunable diode-pumped folded intracavity Q-switched singly resonant optical parametric oscillator based on multi-period MgO:PPLN. A wide tuning mid-infrared parametric light from 2.78 ㎛ to 4.17 ㎛ was obtained in real time by changing the poled periods and temperatures. The maximum output power of 1.89 W at 3.2 ㎛, 1.53 W at 3.5 ㎛, 0.87 W at 3.8 ㎛ and 0.486 W at 4.1 ㎛ were achieved. The highest optical-optical conversion efficiency was 7.89%. During experiments, a range tunable output of 2.78-4.17 ㎛ in the mid-infrared range was achieved.

• Current Optics and Photonics
• /
• v.4 no.4
• /
• pp.273-276
• /
• 2020

We report on the relationship between output current for quadrant photodetector (QPD) and bias voltage in silicon-based p-i-n (positive-intrinsic-negative) QPD examined using millisecond pulse laser (ms pulse laser) irradiation. The mechanism governing the relationship was further studied experimentally. The output current curves were obtained by carrying out QPD under different bias voltages (0-40 V) irradiated by ms pulse laser. Compared to other photodetectors, the relaxation was created in the output current for QPD which is never present in other photodetectors, such as PIN and avalanche photodetector (APD), and the maximum value of relaxation was from 6.8 to 38.0 ㎂, the amplitude of relaxation increases with bias value. The mechanism behind this relaxation phenomenon can be ascribed to the bias voltage induced Joule heating effect. With bias voltage increasing, the temperature in a QPD device will increase accordingly, which makes carriers in a QPD move more dramatically, and thus leads to the formation of such relaxation.

• Journal of the Optical Society of Korea
• /
• v.20 no.5
• /
• pp.541-546
• /
• 2016

In this paper, by using the Rayleigh-Sommer field theory and the cross-spectral density function, the analytical expression for the intensity distribution of a double half-Gaussian hollow beam in a turbulent atmosphere is obtained. The influence of the initial spot size of this beam on its propagation properties in a turbulent atmosphere is simulated, and the intensity distributions for such beams with different spot sizes are obtained. The results show that the initial spot size has an important influence on the propagation properties in the near field, while this influence in the far field is very weak.

• Current Optics and Photonics
• /
• v.5 no.2
• /
• pp.186-190
• /
• 2021

In this study, a compact, picosecond, mid-infrared 3.8 ㎛ MgO:PPLN optical parametric oscillator (OPO) laser output with high peak power is realized using a master oscillator power amplifier (MOPA) 1 ㎛ solid-state laser seeded by a picosecond fiber laser as the pump source. The pump source was a 50 MHz and 10 ps fiber seed source. After AOM pulse selection and two-stage solid-state amplification, a 1,064 nm laser output with a repetition frequency of 1-2 MHz, pulse width of 9.5 ps, and a maximum average power of 20 W was achieved. Furthermore, a compact short cavity with a unsynchronized pump is adopted through the design of an OPO cavity structure. When the injection pump power was 15 W and the repetition frequency was 1 MHz, the average output power of idler light was 1.19 W, and the corresponding peak power was 119 kW. The optical conversion efficiency was 7.93%. When the repetition frequency was increased to 2 MHz, the average output power of idler light was 1.63 W, the corresponding peak power was 81.5 kW, and the optical conversion efficiency was 10.87%. At the same time, the output wavelength was measured at 3,806 nm, and the beam quality was MX2 = 3.21 and MY2 = 3.34.

• Journal of Welding and Joining
• /
• v.32 no.4
• /
• pp.15-19
• /
• 2014

Additive manufacturing technology is taking great attentions in these days because the term 3D-printing became a hot issue as the next generation manufacturing paradigm. Especially, laser additive manufacturing is at the center of interest thanks to the accuracy compared to other heat sources. In this report, recent papers about laser additive manufacturing are analyzed and reviewed. General technology is specified into three different categories and they are laser sintering, laser melting and laser metal deposition. Similarities and differences are clearly described by detailed technologies and used materials type. Representative application examples are selected then future of this technology is expected through those applications. Additionally, market of laser additive manufacturing systems itself and application fields are also predicted based on present 3D-printing market and technical progressions.