• Progress in Superconductivity and Cryogenics
• /
• v.21 no.4
• /
• pp.59-63
• /
• 2019

To reduce the fault current below the current capacity of a circuit breaker, researches on HTS (High Temperature Superconductor) power cables with fault current limiting (FCL) function are increasing. An FCL HTS power cable transports current with low a impedance during normal operation. Yet, it limits the fault current by an increased inductive or resistive impedance of conducting layer when quench occurs at the FCL HTS power cable by the large fault current. An inductive type FCL HTS power cable uses increased inductive impendence caused by leakage magnetic flux outside the cable core when the quench occurs at a shield layer losing the magnetic shielding effect. Therefore, it has an advantage of less resistive heating than resistive type FCL HTS power cable and temperature increase is suppressed. This paper describes an ideal circuit model for the FCL HTS power cable to investigate the effectiveness of increased inductive impedance when quench occurs at the shield layer. Then, FEM analysis is presented with a simplified model cable composed of various iron yokes to investigate the effect of the shape of yoke on the generation of the inductive impedance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.2
• /
• pp.239-244
• /
• 2011

Due to large demand, the increase of fault current has caused the capacity of power machines in power grid to increase. Among several countermeasures, the superconducting fault current limiter (SFCL) has been noticed as one of the promising countermeasures to solve these problems. However, in spite of excellent current limiting performances of the SFCL, the application of SFCL to power system has been delayed due to both the limited space for the SFCL's installation and its longer recovery time after the fault removal. In order to solve these problems, a hybrid type SFCL was developed. In this paper, we studied the operation characteristics of the hybrid SFCL with first half cycle non-limiting operation by modelling using PSCAD/EMTDC and experiment. It was shown through the simulation using PSCAD/EMTDC and the simulated experiment that the fault current limiting and the fast recovery operations of the hybrid SFCL with the first half cycle non-limiting operation were achieved.

• Journal of the Korean Institute of Gas
• /
• v.2 no.3
• /
• pp.12-17
• /
• 1998

Fault tree construction for hazard assessment requires so much time and labor, so it is very difficult to be applied to the large scale chemical plant. For the synthesis of fault tree in chemical processes, this study represents the cause-effect relations between process variables by using the Signed Directed Graph(SDG), and has synthesized Fault Tree(FT) by searching the causes of fault events using the general operator and loop operators defined corresponding to path characteristics on the SDG.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.4
• /
• pp.737-743
• /
• 2008

I compare my parameter estimation methodoloay with existing method, considering both of testing effort and fault detecting rate simultaneously in software reliability modeling. Generally speaking, fault detection/removal mechanism depends on how apply previous fault detection/removal and testing effort of S/W. The fault removal efficiency makes large influence to the reliability growth, testing and removal cost in developing stage S/W. This is very useful measure during all the developing stages and much helpful for the developer to estimate debugging efficiency, and furthermore, to anticipate additional working amount.

• Journal of Aerospace System Engineering
• /
• v.11 no.4
• /
• pp.22-29
• /
• 2017

A study is performed for the effective detection method of a fault which is occurred during operation in a small turbojet engine with non-linear characteristics used by unmanned air vehicle. For this study the non-linear dynamic model of the engine is derived from transient thermodynamic cycle analysis. Also for inducing real operation conditions the controller is developed associated with unscented Kalman filter to estimate noises. Sequential probability ratio test is introduced as a real time method to detect a fault which is manipulated for simulation as a malfunction of rotational speed sensor contaminated by large amount of noise. The method applied to the fault detection during operation verifies its effectiveness and high feasibility by showing good and definite decision performances of the fault.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.28 no.3
• /
• pp.159-164
• /
• 2024

Recent earthquakes in Korea, like Gyeongju and Pohang, have highlighted the need for accurate seismic hazard assessment. The lack of substantial ground motion data necessitates stochastic simulation methods, traditionally used with a simplistic point-source assumption. However, as earthquake magnitude increases, the influence of finite faults grows, demanding the adoption of finite faults in simulations for accurate ground motion estimates. We analyzed variations in simulated ground motions with and without the finite fault method for earthquakes with magnitude (Mw) ranging from 5.0 to 7.0, comparing pseudo-spectral acceleration. We also studied how slip distribution and hypocenter location affect simulations for a virtual earthquake that mimics the Gyeongju earthquake with Mw 5.4. Our findings reveal that finite fault effects become significant at magnitudes above Mw 5.8, particularly at high frequencies. Notably, near the hypocenter, the virtual earthquake's ground motion significantly changes using a finite fault model, especially with heterogeneous slip distribution. Therefore, applying finite fault models is crucial for simulating ground motions of large earthquakes (Mw ≥ 5.8 magnitude). Moreover, for accurate simulations of actual earthquakes with complex rupture processes having strong localized slips, incorporating finite faults is essential even for more minor earthquakes.

• 한국초전도학회:학술대회논문집
• /
• 2007.07a
• /
• pp.12-12
• /
• 2007

• Proceedings of the Korean Society for Quality Management Conference
• /
• 1998.11a
• /
• pp.393-403
• /
• 1998

The advent of very large scale integration(VLSI) has had a tremendous impact on the design of fault-tolerant circuits and systems. The increasing density, decreasing power consumption, and decreasing costs of integrated circuits, due in part to VLSI, have made it possible and practical to implement the redundancy approaches used in fault-tolerant computing. The purpose of this paper is to study the many aspects of designing fault-tolerant systems in a VLSI environment. First, we expound upon the opportunities and problemes presented by VLSI technology. Second, we consider in detail the importance of design mistakes, common-mode failures, and transient faults in VLSI. Finally, we examine the techniques available to implement redundancy using VLSI and the problems associated with these techniques.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.44-44
• /
• 2009

Fault detection is necessary for yield enhancement and cost reduction in semiconductor manufacturing. Sensory data acquired from the semiconductor processing tool is too large to analyze for the purpose of fault detection and classification(FDC). We studied the techniques of fault detection using statistical method. Multiple regression analysis smoothly detected faults and can be easy made a model. For real-time and fast computing time, the huge data was analyzed by each step. We also considered interaction and critical factors in tool parameters and process.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.313-315
• /
• 2005

Recently There has been growing interest in new renewable energy systems with high-energy efficiency due to the increasing energy consumption and environmental pollution problems. But an insertion of new distributed generation to existng power distribution systems can cause several problems such as voltage variations, harmonics, protective coordination, increasing fault current etc, because of reverse power. This paper was applied to fault location defecting a method as each Relay sensing fault current value and carried out short-circuit analysis by MATLAB and PSCAD/EMTDC programs and identity the faulted section o f22.9[kV] distribution system interconnected a large number of distributed generation. The existing protection system of 22.9[kV] power distribution system analyzed and the study on protective coordination recloser and Sectionalzer accomplished